Download
Share
Print this page
Echelon Row Service Manual
  1. Manuals
  2. Brands
  3. Echelon Manuals
  4. Home Gym
  5. ROW
  6. Service manual

Echelon Row Service Manual

Hide thumbs Also See for Row:

Advertisement

Quick Links

Download this manual
R OW
S E R V I C E MA N U A L

Advertisement

loading

Related Manuals for Echelon Row

Summary of Contents for Echelon Row

  • Page 1 R OW S E R V I C E MA N U A L...
  • Page 2 Parts list INCLUDES 1. Echelon® Row Base 8. M8*20 screw with 2. Echelon® Row Rail washer 3. Rear Foot 9. Hex Key 4. Front Foot 10. Left Foot Carriage 5. M8*16 screws 11. Right Foot 6. M10*25 screws Carriage with washer 12.

  • Page 3: Account Creation

    This info will be needed to login to your account on the Echelon Fit App. All account info and plans are managed at member.echelonfit. com and use the same login. After creating your account login on member.echelonfit.com, write down your login info. This will be the same login for the App.
  • Page 4 ASSEMBLY Step 1. Remove the bracket (No.14) Step 2. Place the front foot and and bolt with hex key. hand tighten screws (No. 6) into place. Step 3. Tighten the screws with Step 4. Set rower upright and hex key. adjust the arm of phone holder to your desired level.
  • Page 5 Step 7. Place the rail onto rail Step 8. Place the four screws bracket. (No.5) into rail and hand tighten. ANGLE AWAY FROM ROW Step 9. Tighten screws with hex Step 10. Align front foot with key. screw holes on the rail and hand tighten screws (No.8) into the...
  • Page 6 Step 13. Tighten screws with hex Step 14. Connect the power cord. key. Repeat with left foot carriage. Step 15. Toggle the power switch, as Step 16. Route the power cable shown above. through the cable routing clips legs, as shown above. Step 18.
  • Page 7 Diagnostic procedures for noise Point A Screws of front and rear Point H Screw tube Point I Adjusting screw Point B Screws of foot rest Point J Wheels Point C Monorail Point K Tension controller Point D Mesh belt Point M Plug in power socket Point E Adjusting frame of...
  • Page 8 Diagnostic procedures for power on Point A Screws of front and rear Point H Screw tube Point I Adjusting screw Point B Screws of foot rest Point J Wheels Point C Monorail Point K Tension controller Point D Mesh belt Point M Plug in power socket Point E...
  • Page 9 Diagnostic procedures for CONNECTION with APP Point A Screws of front and rear Point H Screw tube Point I Adjusting screw Point B Screws of foot rest Point J Wheels Point C Monorail Point K Tension controller Point D Mesh belt Point M Plug in power socket Point E...
  • Page 10 Make sure Rowing machine is power on. Step 2: Reconnect the power plug and make sure Check Tension Controller (K) is paired with the socket is functionable. ECH-ROW. Step 3: Re-pair Tension Tension adjustable. Check the battery capacity of Tension...
  • Page 11 Diagnostic procedures for Seat Point A Screws of front and rear Point H Screw Point I Adjusting screw Point B Screws of foot rest Point J Wheels Point C Monorail Point K Tension controller Point D Mesh belt Point M Plug in power socket Point E Adjusting frame of...
  • Page 12 Diagnostic procedures for power on Point A Screws of front and rear Point H Screw tube Point I Adjusting screw Point B Screws of foot rest Point J Wheels Point C Monorail Point K Tension controller Point D Mesh belt Point M Plug in power socket Point E...
  • Page 13 Diagnostic procedures: phone holder cannot be CLAMPED, MOVED and fixed. Point A Screws of front and rear Point H Screw tube Point I Adjusting screw Point B Screws of foot rest Point J Wheels Point C Monorail Point K Tension controller Point D Mesh belt Point M...
  • Page 14 Point G Axle of phone holder arm •Step 1: Make sure ECH-ROW is power on. Tension controller (Point K) is paried with ECH-ROW. ECH-ROW connects APP well. Step 2: Still not power on Adjust the tension up and down Please check Diagnostic by Tension controller (Point K).
  • Page 15 Replacement of Handlebar Models: Echelon Row Read below instruction carefully. Making sure you carefully screw in controller and do not pull the wire out. See more information in the instruction manual. TOOLS Screwdriver Step 1. Step 2. Remove 5PCS of screws...
  • Page 16 Replacement of Handlebar Models: Echelon Row Step 8. Replace with new handle Step 9. Step 10. Re-assemble the controller Place 5PCS of screws Step 11. Flip back handle. Handle Tighten 5PCS of screws replacement Complete...
  • Page 17 Replacement of Controller and RE-Pairing Controller with Row Models: Echelon Row Read below instruction carefully. Making sure you carefully screw in controller and do not pull the wire out. See more information in the instruction manual. TOOLS Screwdriver Step 1.
  • Page 18 Replacement of Controller and RE-Pairing Controller with Row Models: Echelon Row Step 8. Flip back and put onto Tighten 5PCS of screw the holder Step 9. Step 10. Press both tension control After 30 sec, the blue light bottons simutaneously for...
  • Page 19 Replacement of Module controller Models: Echelon Row Read below instruction carefully. See more information in the instruction manual. TOOLS Screwdriver Step 1. Step 2. Remove cable ties Unscrew the BLT controller Step 3. Step 4. Unscrew the BLT controller Disconnect the cable Step 5.
  • Page 20 Replacement of Module controller Models: Echelon Row Step 7. Step 8. Step 9. Connect cables Tie the cable. Check connection. 1. Plug the power switch 2. Check all connection well. 3. If change the RF controller, check connection after replacement...
  • Page 21 Replacement of Sensor Models: Echelon Row Read below instruction carefully. See more information in the instruction manual. TOOLS Adhesive Industrial alcohol 2mm card- for check the distance between sensor and magnet Screwdriver Cable ties Cutter Step 1. Step 2. Remove Cover Remove cable ties Step 3.
  • Page 22 Replacement of Sensor Models: Echelon Row Step 6. Step7. Make sure the distance Replace new sensor between sensor and magnet is 2mm Step 8. Step 9. Step 10. Fix the distance by Adhesive the connector Fasten by cable tie adhesive Step 11.
  • Page 23 Replacement of Seat Models: Echelon Row Read below instruction carefully. See more information in the instruction manual. TOOLS Place seat on ground and lay the rail onto seat so the screw holes on the bracket align with screw holes on seat.
  • Page 24 Replacement of Pedals inclued plastic parts. Models: Echelon Row Read below instruction carefully. See more information in the instruction manual. TOOLS S6 Hex Key S4 Hex Key Screwdriver Step 1. Step 2. Remove Pedal from main Remove screws from back plate freame Step 3.
  • Page 25 Replacement of Seat wheels Models: Echelon Row Read below instruction carefully. See more information in the instruction manual. TOOLS M14 sleeve tool S6 Hex Key Step 1. Remove rail cap Step 2. Remove the bolt from rail. Step 3. Step 4.
  • Page 26 Replacement of Seat wheels Models: Echelon Row Step 6. Step 7. Step 8. Re-assemble the controller Tighten the wheels Place 5PCS of screws Step 9. Step 10. Step11. Tighetn Bolt on rail. Assemble cap on rail. Finished...
  • Page 27 Replacement of flywheel Models: Echelon Row Read below instruction carefully. See more information in the instruction manual. TOOLS Screwdriver M14 sleeve tool M10 wrench M17 wrench Measure Step 1. Step 2 Remove the bolt from rail. Loosen nuts (8) and (13) from coil.
  • Page 28 Replacement of flywheel Models: Echelon Row Step 7. Step 8. Step 9. Assemble the belt on coil, Tighten nut(13) on main Make sure the belt in the make sure the direction as the frame middle of flywheel axle picutre while spin the flywheel Step 10.
  • Page 29 Replacement of coil Models: Echelon Row Read below instruction carefully. See more information in the instruction manual. TOOLS Screwdriver M14 sleeve tool M10 wrench M17 wrench S6 Hex Key Step 1. Step 2 Remove nuts(10) and plate Remove cover Step 3.
  • Page 30 Replacement of coil Models: Echelon Row Step 7. Let mesh belt go back to coil slowly Step 8. Step 9. Remove the belt(12) from coil, the flywheel can Remove the coil from only spin as arrow direction see picture. main frame Step 10.
  • Page 31 Replacement of coil Models: Echelon Row Step 13. Step 14. Make sure the belt as the picture. Assemble the screw (10) Step 15. Step 16. Step 17. Put the nut(8) on alxe, do D shape put on right side. Put the nut(10) and plate on not tighten it.
  • Page 32 Replacement of coil Models: Echelon Row Step 20. Step 21 Pull the mesh belt then across the lower roller Remove the upper roller hang on holder Step 22. Step 23. Step 24. Assemble the cover cushion Assemble the upper roller...