Campbell Hausfeld WS0900 Operating Instructions And Parts Manual page 9

Symptom
Bead is intermittently too
thin or too thick
Ragged depressions at edge
of weld
Weld bead does not
penetrate workpiece
Electrode sticks to work
piece
Electrodes sputter and stick
Limited 5-3-1 Warranty
1. Duration: The manufacturer warrants that it will repair, at no charge for parts or labor, the Welder, Welding Gun, or Cables, proven
defective in material or workmanship, during the following time period(s) after date of original retail purchase:
For 5 Years: The Welder Transformer and Rectifier
For 3 Years: The Entire Welder (excluding clamps, welding gun, electrode holder, cables, or accessories packed with welder)
For 1 Year: The Welding Clamps, MIG Gun, Electrode Holder, Accessories, and Welding Cables (as applicable)
2. Who Gives This Warranty (Warrantor):
The Campbell Group / A Scott Fetzer Company
100 Production Drive
Harrison, OH 45030
Telephone: (513)-367-4811
3. Who Receives This Warranty (Purchaser): The original purchaser of the Campbell Hausfeld product.
4. What is covered under this warranty: Defects in material and workmanship which occur within the duration of the warranty period.
This warranty extends to the Welder, the Welders Transformer and Rectifier, Welding Gun or Electrode Holder, and cables only.
5. What is not covered under this warranty:
A. Implied warranties, including those of merchantability and FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED IN DURATION TO THIS
EXPRESS WARRANTY. After this period, all risks of loss, from whatever reason, shall be on the purchaser. Some states do not allow
limitations on how long an implied warranty lasts, so above limitations may not apply to you.
B. ANY INCIDENTAL, INDIRECT, OR CONSEQUENTIAL LOSS, DAMAGE, OR EXPENSE THAT MAY RESULT FROM ANY DEFECT FAILURE OR
MALFUNCTION OF THE CAMPBELL HAUSFELD PRODUCT. Some states do not allow limitations on how long an implied warranty lasts,
so above limitations may not apply to you.
C. This warranty does not apply to any accessory items included with the product which are subject to wear from usage; the repair or
replacement of these items shall be at the expense of the owner. These MIG items include but are not limited to; Contact Tips, Nozzles,
Gun Liners, Drive Rollers, Felt Wire Cleaner. In addition, this warranty does not extend to any damage caused by the untimely
replacement or maintenance of any of the previously listed CONSUMABLE parts.
D. Any failure that results from accident, purchaser's abuse, neglect or failure to operate products in accordance with instructions
provided in the owner's manual(s) supplied with the product.
E. Pre-delivery service, i.e. assembly and adjustment.
7. Responsibilities of Warrantor under this warranty: Repair or replace, at Warrantor's option, products or components which have
failed within duration of the warranty period.
8. Responsibilities of purchaser under this warranty:
A. Deliver or ship the Campbell Hausfeld product or component to Campbell Hausfeld. Freight costs, if any, must be borne by the
purchaser.
B. Use reasonable care in the operation and maintenance of the products as described in the owner's manual(s).
9. When Warrantor will perform repair or replacement under this warranty: Repair or replacement will be scheduled and serviced
according to the normal work flow at the servicing location, and depending on the availability of replacement parts.
This Limited Warranty gives you specific legal rights and you may also have other rights which vary from state to state.
Troubleshooting Chart - Welds
Possible Cause(s)
1. Inconsistent travel speed
2. Output amp setting incorrect
1. Travel speed too fast
2. Arc length too short
3. Output amp setting too high
1. Inconsistent travel speed
2. Output amp setting too low
3. Electrode diameter too large
1. Arc length short
2. Amp setting low
Damp electrodes
Models WS0900, WS090001, WS0950, WS1000 and WS1020
Corrective Action
1. Carefully watch and control the width of the molten weld
bead
2. Adjust output amp setting or change to smaller diameter
electrode
1. Watch orange molten weld puddle and control bead width
2. Practice running electrode across workpiece with welder
OFF
3. Reduce output amp setting
1. Decrease and maintain constant travel speed
2. Increase output amp setting or change to smaller diameter
electrode
3. Recommend either 1/16 or 5/64 diameter
1. Lift electrode to correct arc length as soon as arc is struck
2. Increase amp setting or change to smaller diameter
electrode
Use dry electrodes and store in dry location
9
www.campbellhausfeld.com