Advertisement
To view the time in another city
In the World Time Mode, use D to move the stopwatch second hand to the
city code of the city you want to select as the World Time city.
• The hour hand, minute hand, and date display will change automatically to
the applicable settings for the currently selected city code.
• The day of the week hand shows whether or not Daylight Saving Time
(summer time) is turned off for the currently selected city code.
• All buttons (except for C for changing modes) are disabled while the hands
and date display are changing.
• The watch will beep if the city code you select is your current Home City.
• For full information on city codes, see the "City Code Table".
To toggle a city code time between Standard Time and Daylight
Saving Time
1. In the World Time Mode, use D to select the
city code whose Standard Time/Daylight
Saving Time setting you want to change.
2. Hold down A for about three seconds until
the watch beeps. This will cause the day of the
week hand to toggle between ON (Daylight
Saving Time) and OFF (Standard Time).
• Note that you cannot switch between Standard
Time and Daylight Saving Time while GMT is
L
selected as the city code.
Hold down
• Note that the Standard Time/Daylight Saving
A for three
Time setting affects only the currently
seconds.
displayed city code. Other city codes are not
affected.
• The Standard Time/Daylight Saving Time
setting of your Home City can be changed in
the Timekeeping Mode only. See "To set the
time and date manually" for more information.
Swapping your Home City and World Time City
You can use the procedure below to swap your Home City and World Time
city. This changes your Home City to your World Time city, and your World
Time city to your Home City. This capability can come in handy when you
frequently travel between two cities in different time zones.
• If your current World Time city supports receipt of a time calibration signal,
making it your Home City enables calibration signal reception.
To swap your Home City and World Time city
1. In the World Time Mode, use D to select the World Time city you want.
2. Hold down B for about three seconds until the watch beeps twice.
• This will make the World Time city (which you selected in step 1), your
Home City. At the same time, it changes the Home City you had selected
prior to step 2 your World Time city.
• After swapping the Home City and World Time city, the watch stays in the
World Time Mode with the city that was selected as the Home City prior to
step 2 now displayed as the World Time city.
Alarm
When the alarm is turned on, the alarm sounds
Alarm time
Mode
when the alarm time is reached.
(minute)
indicator
• The day of the week hand points to AL while
the watch is in the Alarm Mode. The stopwatch
second hand points to the current alarm on
(ON)/off (OFF) setting, while the hour, minute,
and 24-hour hands indicate the current alarm
time setting.
• All of the operations in this section are
performed in the Alarm Mode.
To set an alarm time
Alarm time (hour)
1. In the Alarm Mode, hold down A for about
three seconds until the watch beeps. This
indicates it is in the setting mode.
• The stopwatch second hand will move to
ON (alarm on) at this time.
2. Use D (+) and B (–) to change the alarm time setting.
• Each press of either button moves the hands one-minute.
3. After setting the alarm time, press A to exit the setting mode.
• Setting the alarm time causes the alarm to turn on automatically.
• As you set the alarm time, take care to ensure that the 24-hour hand also is
at the correct position.
Alarm Operation
The alarm tone sounds at the preset time for 10 seconds, regardless of the
mode the watch is in.
• Alarm operations are performed in accordance with the Timekeeping Mode
time.
• Pressing any button stops the alarm tone operation.
To toggle an alarm on and off
In the Alarm Mode, press A to toggle the alarm ON and OFF.
Operation Guide 5035
Adjusting the Home Positions
If the time and date settings are wrong even after the time calibration signal is
received normally, use the following procedure to adjust their home positions.
To adjust the home positions
1. In the Timekeeping Mode, as you hold down
Stopwatch second hand
A, hold down C for about three seconds
until the watch beeps.
• This indicates that the watch is in the time
and date home position adjustment mode.
• First is timekeeping second hand and
stopwatch second hand home position
adjustment.
• If the timekeeping second hand moves to
Timekeeping
"0", it is in the correct home position. If it
second hand
doesn't, use D to move the timekeeping
Correct timekeeping second
second hand to "0".
hand and stopwatch second
• The stopwatch second hand is also in the
hand home positions
proper home position if it moves to 12
o'clock. If it doesn't, press B to move it to
Minute hand
Hour hand
12 o'clock.
2. After confirming that the timekeeping second
hand and stopwatch second hand are both at
the proper home positions, press C.
This will switch to hour hand and minute hand
home position adjustment.
• The hour hand and minute hand are at their
proper home positions if they both move to
12 o'clock, and if the 24-hour hand is
pointing at hour 24. If the hands are not
24-hour hand
positioned correctly, use D (+) and B (–)
Correct hour and minute
to move all three hands to their proper home
hand home position
positions.
• The 24-hour hand moves in accordance
Day of the week hand
with the hour, minute, and second settings.
As you set the time, take care to ensure that
the 24-hour hand also is at the correct
position.
3. After confirming that the hour and minute
hands are in the correct home position, press
C. This will advance to day of the week hand
home position adjustment.
• The day of the week hand is in the correct
Correct day of the week
home position if it is pointing at 0 (or 60). If it
hand home position
isn't, use D (+) and B (–) to move the
hand to 0 (or 60).
4. After confirming that the day of the week hand
is in the correct home position, press C. This
will advance to date home position
adjustment.
• The date is in the correct home position if it
shows "1". If it doesn't, use D (+) and B
(–) to change the date to "1".
• Pressing C here will return to the
Date
timekeeping second hand and stopwatch
Correct date home position
second hand home position adjustment in
step 1 of this procedure.
5. Press A to return to the Timekeeping Mode.
• After you complete the home position adjustment procedure, place the
watch in a location that allows good time calibration signal reception, and
then perform a manual receive operation. See "To perform manual receive"
for more information.
Timekeeping
Use the Timekeeping Mode to set and view the
Stopwatch
current time and date. This section also explains
Hour hand
second hand
how to set the current date and time manually.
• All of the operations in this section are
24-hour
Minute
hand
hand
performed in the Timekeeping Mode.
To set the time and date manually
1. In the Timekeeping Mode, hold down A for
about five seconds until the watch beeps twice.
• The stopwatch second hand will move to the
city code of the currently selected Home
City. This is the city code setting mode.
• The second hand will stop at "0".*
* Some models show "60" instead of "0".
Timekeeping
Day of the
2. Use D to change the Home City setting.
second hand
week hand
• For full information on city codes, see the
Date
"City Code Table".
3. Use B to toggle the DST setting on (ON) and off (OFF).
• Even after you change the DST setting, you can still use D to select a
different Home City code if you want.
4. After the Home City and DST settings are the way you want, press C.
• This will cause the watch to beep, and the stopwatch second hand and
day of the week hand to move to their 12 o'clock positions. This is the
time setting mode.
4
Advertisement
