Advertisement
etc.). If the screws and screw anchors are provided with the
product, check that they are suitable for the type of wall on
which the hood is to be fi xed.
• FIXING THE DECORATIVE TELESCOPIC FLUE
Take care not to scratch the duct; wear gloves when
removing the protective fi lm. (Fig. 7)
Arrange the electrical power supply within the dimensions
of the decorative fl ue. If your appliance is to be installed in
the ducting version or in the version with external motor,
prepare the air exhaust opening. Adjust the width of the
support bracket of the upper fl ue (Fig.3). Then fi x it to the
ceiling using the screws A (Fig.3) in such a way that it is
in line with your hood and respecting the distance from the
ceiling indicated in Fig.2. Connect the fl ange C to the air
exhaust hole using a connection pipe (Fig.4).
Insert the upper fl ue into the lower fl ue. Fix the lower fl ue
to the hood using the screws B provided (Fig.4), extract
the upper fl ue up to the bracket and fi x it with the screws
B (Fig.3).
To transform the hood from a ducting version into a fi ltering
version, ask your dealer for the charcoal fi lters and follow
the installation instructions.
• FILTERING VERSION
Install the hood and the two flues as described in the
paragraph for installation of the hood in ducting version. To
assemble the fi ltering fl ue refer to the instructions contained
in the kit. If the kit is not provided, order it from your dealer as
accessory. The charcoal fi lters must be fi tted in the ducting
unit located inside the hood (Fig.6).
USE AND MAINTENANCE
• It is recommended to operate the appliance prior to
cooking.
It is recommended to leave the appliance in operation for 15
minutes after cooking is terminated in order to completely
eliminate cooking vapours and odours.
The proper function of the cooker hood is conditioned by the
regularity of the maintenance operations, in particular, the
active carbon fi lter.
• The anti-grease filters capture the grease particles
suspended in the air, and are therefore subject to clogging
according to the frequency of the use of the appliance.
In order to prevent fi re hazard, it is recommendable to clean
the fi lter at a maximum of 2 months by carrying out the
following instructions:
- Remove the fi lters from the cooker hood and wash them
in a solution of water and neutral liquid detergent, leaving
to soak.
- Rinse thoroughly with warm water and leave to dry.
- The fi lters may also be washed in the dishwasher.
The aluminium panels may alter in colour after several
washes. This is not cause for customer complaint nor
replacement of panels.
• The active carbon fi lters purify the air that is replaced in
the environment. The fi lters are not washable nor re-useable
and must be replaced at maximum every four months. The
saturation of the active carbon fi lter depends on the frequency
of use of the appliance, by the type of cooking and the
regularity of cleaning the anti-grease fi lters.
• Clean the fan and other surfaces of the cooker hood
regularly using a cloth moistened with denatured alcohol or
non abrasive liquid detergent.
• The illumination installation is designed for use during
cooking and not for prolonged general illumination of the
environment. Prolonged use of the illumination installation
notably reduces the duration of the bulb.
• Replacing halogen light bulbs (Fig. 8).
To replace the halogen light bulbs B, remove the glasspane
C using a lever action on the relevant cracks.Replace the
bulbs with new ones of the same type.
Caution: do not touch the light bulb with bare hands.
COMMANDS: (Fig.9)
Push-button A = on/off lights switch
Push-button B = on/off cooker hood switch. The appliance
switches on at speed level 1, If the cooker hood is on
depress the push-button for 2 sec. to switch off the cooker
hood. If the cooker hood is at speed level 1 it will not be
necessary to depress the push-button to switch the cooker
hood off. Decreases the motor speed.
Display C = indicates the motor speed level selected and
activates the timer.
Push-button D = switches on the cooker hood. Increases
the motor speed. Touching the key at 3rd speed, the
intensive function runs for 10', then the appliance go back
to work at the original speed. During this function the
display blinks.
Key E = The Timer times the functions on activation for
15 minutes, after which they are switched off. The Timer
is deactivated by re-pressing Key E. When the Timer
is activated the decimal point must fl ash on the display.
The Timer cannot be activated if the intensive speed is
functioning.
The "clean air" function is activated by pressing key E for 2
seconds when the appliance is switched off. This switches
the motor on for 10 minutes every hour at the fi rst speed.
During functioning a rotary movement of the peripheral
segments must be visualised on the display. When this time
has passed the motor switches off and the fi xed letter "C"
must be visualised on the display until the motor re-starts
after 50 minutes for another 10 minutes and so on. Press any
key apart from the light keys to return to normal functioning.
Press key E to deactivate the function.
• Active carbon/grease fi lter saturation:Fig.9
- When display item C fl ashes, at a speed where it alternates
with the letter F (e.g. 1 and F), the grease fi lters must be
washed.
- When display item C fl ashes, at a speed where it alternates
with the letter A (e.g. 1 and A), the carbon fi lters must be
replaced.
After the clean fi lter has been positioned correctly, the
electronic memory must be reset by pressing button A for
approximately 5 seconds, until the indication F or A shown
on the display C stops fl ashing.
THE MANUFACTURER DECLINES ALL RESPONSIBILITY
FOR EVENTUAL DAMAGES CAUSED BY BREACHING
THE ABOVE WARNINGS.
- 19 -
Advertisement
