SECTION 1 PRECAUTION SAFETY PRECAUTIONS (1) The design of this product contains special hardware, many (10) Isolation Check (Safety for Electrical Shock Hazard) circuits and components specially for safety purposes. For After re-assembling the product, always perform an isolation continued protection, no changes should be made to the original check on the exposed metal parts of the cabinet (antenna design unless authorized in writing by the manufacturer.
Page 5
INSTALLATION 1.2.1 INSTALLATION SITE (1) The rear of this set is provided with ventilation openings. Install the set more than 5 cm from a wall and in a location (more than 5cm) with good ventilation. (2) Avoid the following types of locations. a) Unstable locations (location must be able to withstand heavy weight).
SECTION 2 SPECIFIC SERVICE INSTRUCTIONS FEATURES • Rear Projection HDTV. • Bullet-in DSD (Digital Super Detail) circuit and 3 dimension Y/ • New chassis design enable use of an interactive on screen C separate circuit. control. • Receive DTV broadcast (1080i / 720p / 480p / 480i) •...
Page 7
REMOTE CONTROL UNIT [RM-C1257G] POWER key VCR / DVD switch TV / CATV switch MULTI SCREEN MULTI SCREEN operation keys TWIN INDEX C.C. DISPLAY key FREEZE SWAP INPUT SELECT SLEEP TIMER key SOUND key SOUND VIDEO STATUS key TUNE THEATER PRO key ASPECT LIGHT ASPECT key...
Page 8
TECHNICAL INFORMATION 2.4.1 MAIN MICRO COMPUTER (CPU) FUNCTION (MN102H75K) Pin No. Pin name Function Pin No. Pin name Function Lighting for on timer operating -------- ON_TIM [LOW / ON:H] /MICON_V V.sync for OSD SBO 0 Convergence control [RXD] Low B protection detection LB_PRO SBD 0 Convergence control [TXD]...
Page 9
MAIN PARTS LOCATION 2.5.1 PWB ASS'Y ARRANGEMENT The PWB ASS'Y is indicated below. PWB ASS'Y name AV-48P575HA AV-56P575HA AV-56P585HA MAIN PWB ASS'Y SRP-1003A-M2 SRP-1004A-M2 SRP-1002A-M2 ← ← MI-COM & DIST MODULE PWB ASS'Y SRP0D001A-M2 ← ← POWER PWB ASS'Y SRP-9001A-M2 ←...
Page 10
SCREEN HANDLING CAUTIONS 2.6.1 SCREEN STORAGE Store the SCREEN ASS'Y in a standing position in order to avoid deformation. If the screen is stored horizontally, there is risk of deforming the screen face. When necessary to place the SCREEN ASS'Y horizontally, position the screen side upwards and sure to place spacers between the screen and resting site (floor or stand etc.) to prevent the screen from sagging.
SECTION 3 DISASSEMBLY DISASSEMBLY PROCEDURE SPEAKER • Make sure that the power cord is pulled out from the AC wall WIRE socket. 3.1.1 SPEAKER GRILLE (1) Remove 2 screws [ A ] from rear side. (2) The SPEAKER GRILLE bottom is pulled to the front, and four claws which are fixing the SPEAKER GRILLE are removed.
Page 12
3.1.6 SCREEN ASS'Y • Take out the SPEAKER GRILLE. • Take out the FRONT CONTROL BOX. SCREEN ASS'Y (1) Disconnect the connector [ CN00Z ] (2) Remove 4 screws [ G ] attaching the SCREEN ASS’Y. (3) Remove 10 screws [ H ] from rear side. (4) Take out the SCREEN ASS'Y.
Page 13
3.1.9 REAR PANEL (1) Remove 6 screws [ K ]. (2) Remove 4 screws [ L ]. (3) Take out the REAR PANEL. NOTE : • Before the rear panel is inserted into the cabinet, release the short-circuit between the [SB] connector (1) pin and (2) pin of the DIGITAL INPUT UNIT.
Page 14
3.1.12 MAIN UNIT • Take out the SPEAKER GRILLE. • Take out the FRONT PANEL. • Take out the REAR PANEL. FOCUS PACK (1) Remove 4 screws [ O ] from front side. CLAMP SPEAKER (2) Take out the connector [CN00R], [CN001G], [CN001H] on MAIN UNIT WIRE the FRONT CONTROL PWB.
Page 15
3.1.16 MAIN CHASSIS • Take out the REAR PANEL. (1) Remove 2 screws [ U ]. (2) Remove 2 screws [ P ]. (3) Pull out the MAIN CHASSIS for backside. DIGITAL CONVERGENCE MODULE PWB NOTE: If necessary, remove the anode wires, connectors, respectively.
Page 16
MEMORY IC REPLACEMENT 3.2.1 MEMORY IC This memory IC stores data for proper operation of the video and SERVICE MENU deflection circuits. When replacing, be sure to use an IC containing this (initial value) data. 1.PICTURE/SOUND 7.CONVER B 2.YC SEP 8.IP 3.WHITE BALANCE 9.DSD...
Page 17
3.2.4 FACTORY SHIPPING SETTING VIDEO STATUS MEMORY (NTSC / 480i / 480p) Setting value Item TINT COLOR PICTURE BRIGHT DETAIL STANDARD THEATER DYNAMIC GAME (720p / 1080i) Setting value Item TINT COLOR PICTURE BRIGHT DETAIL STANDARD THEATER DYNAMIC GAME CHANNEL SETTING (CHANNEL SUMMARY) Band CH display Setting...
Page 18
SHIPPING FACTORY SETTING (USER SETTING) Setting item Setting value Setting item Setting value POWER TINT / COLOR / PICTURE/ Refer to setting of Video status CHANNEL CABLE-02 BRIGHT / DETAIL memory at shipping factory VOLUME setting INPUT COLOR TEMPERATURE DIG. NOISE CLEAR VSM (Velocity Scan Modulation) DISPLAY NATURAL CINEMA...
Page 19
REPLACEMENT OF CHIP COMPONENT 3.3.1 CAUTIONS (1) Avoid heating for more than 3 seconds. (2) Do not rub the electrodes and the resist parts of the pattern. (3) When removing a chip part, melt the solder adequately. (4) Do not reuse a chip part after removing it. 3.3.2 SOLDERING IRON (1) Use a high insulation soldering iron with a thin pointed end of it.
SECTION 4 ADJUSTMENT ADJUSTMENT PREPARATION (1) You can make the necessary adjustments for this unit with SETTING POSITION either the Remote Control Unit or with the adjustment tools Setting item Setting position and parts as given below. VIDEO STATUS STANDARD (2) Adjustment with the Remote Control Unit is made on the TINT / COLOR / PICTURE / basis of the initial setting values, however, the new setting...
Page 21
ADJUSTMENT LOCATION FRONT CONTROL PWB INPUT-4 SUPER MENU CH - CH + VOL - VOL + FOCUS S-VIDEO VIDEO POWER SW CN001H CN001G CN000R DIGITAL INPUT MODULE PWB FRONT REMOCON SENSOR PWB MAIN PWB R SPEAKER L SPEAKER FRONT FRONT CN1001 CN001 CN1002...
Page 22
B VM COIL VM PWB G VM COIL R VM COIL SCREEN MI-COM&DIST MODULE PWB CN000E FOCUS CONVERGENCE SENSOR FOCUS PACK TP-B TP-G TP-R B CRT G CRT R CRT TP-EB TP-EG TP-ER SOCKET SOCKET SOCKET MI-COM&DIST MODULE PWB CN000Y FRONT FRONT CN00Z...
Page 23
BASIC OPERATION OF SERVICE MENU SERVICE MENU 1.PICTURE/SOUND 7.CONVER B 2.YC SEP 8.IP 3.WHITE BALANCE 9.DSD 4.MEMORY SETUP 0.HDMI 5.RF AFC 6.CONVER A DO NOT ADJUST 1.PICTURE/SOUND 5.RF AFC NTSC FULL ST L FL MUTE TOO HIGH GOOD TOO LOW TUNER MAIN FINE...
Page 24
4.5.1 TOOL OF SERVICE MENU OPERATION Operate the SERVICE MENU with the REMOTE CONTROL UNIT. 4.5.2 SERVICE MENU ITEMS In general, basic setting (adjustments) items or verifications are performed in the SERVICE MENU. 1.PICTURE / SOUND This sets the setting values of the VIDEO, AUDIO and DEFLECTION circuits. 2.YC SEP This is used when the YC SEPARATION circuit is adjusted.
Page 25
4.5.5 SERVICE MENU SETTING 1. PICTURE/SOUND 3. WHITE BALANCE AUDIO / VIDEO / DEFLECTION circuit adjustment. Adjustment of LOW LIGHT / HIGH LIGHT. 1. SETTING ITEM No. 1. SELECT ITEM • Press [CH+] / [CH-] key : AUDIO 2. SETTING VALUE : SIGNAL BRIGHT : DEFLECTION...
Page 26
6. CONVER A 8. IP Setting the CONVERGENCE PHASE adjustment. DIST circuit data setting. • Setting for 6.CONVER A is described in the CONVERGENCE [Do not adjust] adjustment. 8.IP 6.CONVER A SETTING ITEM No. CPA01~CPA11 NTSC FULL ST L FL MUTE CCA01~CCA12 SETTING ITEM No.
Page 27
INITIAL SETTING VALUE OF SERVICE MENU (1) Adjustment of the SERVICE MENU is made on the basis of the initial setting values; however, the new setting values which set the screen in its optimum condition may differ from the initial setting. (2) Do not change the initial setting values of the setting items NOT LISTED IN ADJUSTMENT.
Page 28
DEFLECTION SYSTEM Item SINGLE PICTURE Item name Variable range TWIN / INDEX (FULL) D01 V. SIZE 000~127 D02 EW 000~063 D03 H. SIZE 000~063 D04 V. SCORE 000~063 D05 V. LINE 000~063 D06 V. CENT 000~063 D07 EW.TRAP 000~063 D08 BOT.CORN 000~015 D09 TOP.CORN 000~015...
Page 29
VIDEO SYSTEM ( NTSC / 480i ) NTSC 480i Item Item name Variable range STANDARD THEATER STANDARD THEATER 48" 56" 48" 56" 48" 56" 48" 56" S01 COLOR 000~255 S02 TINT 000~255 ( 480p / 720p / 1080i ) 480p 720p / 1080i Item Item name...
Page 30
( NTSC / 480i ) NTSC 480i STANDARD THEATER STANDARD THEATER Item Item name Variable range HIGH HIGH HIGH HIGH 48" 56" 48" 56" S10 DRIVE R 000~255 (Not display) -128 ~ +127 +004 +006 +014 +005 +006 +014 S12 DRIVE B 000~255 (Not display) -128 ~ +127...
Page 31
( NTSC / 480i / OTHERS SIGNAL ) NTSC 480i OTHERS SIGNAL Item Item name Variable range STANDARD THEATER STANDARD THEATER STANDARD THEATER S23 DC CTL 000~255 Item Item name Variable range Initial setting value S24 RGBLIMT 000~015 ( NTSC / 480i / OTHERS SIGNAL ) Item Item name Variable range...
Page 32
( TWIN / REGULER / THEATER / OTHERS ) MULTI SCREEN ASPECT VIDEO STATUS Item Item name Variable range OTHERS TWIN REGULAR THEATER S47 ACL EERG 000~255 Item Item name Variable range Initial setting value S48 CHRM GM 000~255 Item Item name Variable range Initial setting value S49 OSDR DC...
Page 33
OTHERS Initial setting value ASPECT Item Item Item name Variable range Item name Variable range CINEMA OTHERS 48P575 56P575 56P585 F01 E 1 000~255 F09 AUTOSCR1 000~015 F02 E 2 000~255 F10 AUTOSCR2 000~015 (Not display) 000~255 F11 AUTOSCR3 000~015 F04 CATVMAX 000~255 F12 AUTOSCR4...
Page 34
4.6.2 [2.YC SEP] (All fixed) Variable Initial setting Item No. Item name NOTE : range value Initial setting value is reference value at following condition. YCM040 (Not display) 000~003 INPUT SIGNAL : NTSC YCM041 (Not display) 000~063 ASPECT : FULL YCM042 (Not display) 000 / 001...
Page 35
Variable Initial setting Variable Initial setting Item No. Item name Item No. Item name range value range value YCM085 (Not display) 000 / 001 YCM130 (Not display) 000~003 YCM086 (Not display) 000 / 001 YCM131 (Not display) 000~255 YCM087 (Not display) 000~063 YCM132 (Not display)
Page 36
Variable Initial setting Variable Initial setting Item No. Item name Item No. Item name range value range value YCM175 (Not display) 000 / 001 YCS033 (Not display) 000 / 001 YCM176 (Not display) 000 / 001 YCS034 (Not display) 000 / 001 YCM177 (Not display) 000~255...
Page 37
4.6.3 [3.WHITE BALANCE] Variable Initial setting Item No. Item name range value NOTE : Initial setting value is reference value at following condition. YCS078 (Not display) 000 / 001 INPUT SIGNAL : NTSC YCS079 (Not display) 000 / 001 ASPECT : FULL YCS080 (Not display)
Page 38
Variable Initial setting Variable Initial setting Item No. Item name Item No. Item name range value range value CBA37 CURSOL COL CDA01 DF DC -512~511 CBA38 CROSS COL CDA02 DF H1 -512~511 CBA39 SQUARE COL CDA03 DF H2 -512~511 CBA40 XCPOS VPOS 0~31 CDA04...
Page 39
Variable Initial setting Variable Initial setting Item No. Item name Item No. Item name range value range value CBA82 SQ7VSIZE 0~255 IPA024 (Not display) 000 / 001 CBA83 SQ7HSIZE 0~255 IPA025 (Not display) 000 / 001 CBA84 SQ8POSV 0~2047 IPA026 (Not display) 000~03F CBA85...
Page 40
Variable Initial setting Variable Initial setting Item No. Item name Item No. Item name range value range value DSA018 (Not display) 000~03F DSB001 (Not display) (Not display) DSA019 (Not display) 000 / 001 DSB002 (Not display) (Not display) DSA020 (Not display) 000~03F DSB003 (Not display) (Not display)
Page 41
Variable Initial setting Variable Initial setting Item No. Item name Item No. Item name range value range value DSB046 (Not display) (Not display) DSC036 (Not display) 000~0FF DSB047 (Not display) (Not display) DSC037 (Not display) 000~00F DSB048 (Not display) (Not display) DSC038 (Not display) 000~0FF...
Page 42
Variable Initial setting Variable Initial setting Item No. Item name Item No. Item name range value range value HDM009 (Not display) 000 / 001 HDM054 (Not display) 000 / 001 HDM010 (Not display) 000 / 001 HDM055 (Not display) 000 / 001 HDM011 (Not display) 000 / 001...
Page 43
Variable Initial setting Variable Initial setting Item No. Item name Item No. Item name range value range value RHD017 (Not display) (Not display) RHD062 (Not display) (Not display) RHD018 (Not display) (Not display) RHD063 (Not display) (Not display) RHD019 (Not display) (Not display) RHD064 (Not display) (Not display) RHD020...
Page 44
Variable Initial setting Variable Initial setting Item No. Item name Item No. Item name range value range value RHD107 (Not display) (Not display) RHD152 (Not display) (Not display) RHD108 (Not display) (Not display) RHD153 (Not display) (Not display) RHD109 (Not display) (Not display) RHD154 (Not display) (Not display) RHD110...
Page 45
ADJUSTMENT PROCEDURE 4.7.1 CHECK ITEMS Measuring Item Test point Adjustment part Description instrument X-RAY Resistor S1 connector (1) Receive NTSC whole black signal. PROTECTOR [6.8kΩ 2 pin : X-Ray2 (2) Connect resistor 6.8kΩ (1/4W, ±34Ω) between 2 pin check 1/4W ±34Ω] 3 pin : X-Ray1 &...
Page 46
4.7.3 FOCUS & BEAM SPOT ADJUSTMENT Measuring Item Test point Adjustment part Description instrument FOCUS & Signal TEST MODE (1) Receive NTSC crosshatch signal. BEAM SPOT generator [5.CONVER OFF] (2) Select FULL mode with [ASPECT] key. adjustment (3) Select DYNAMIC mode with [VIDEO STATUS] key. Similar R Def.
Page 47
4.7.4 DEFLECTION & CONVERGENCE ADJUSTMENT • The adjustment using the remote control unit is made on the basis of the initial setting values. • The setting values which adjust the screen to the optimum condition can be different from the initial setting values. •...
Page 48
4.7.4.2 PREPARATION Measuring Item Test point Adjustment part Description instrument SCREEN TILT Signal TEST MODE • Confirm correct FOCUS adjustment. (1) Receive NTSC crosshatch signal. adjustment generator [5.CONVER OFF] (2) Enter TEST MODE [5.CONVER OFF]. (3) Select crosshatch pattern with [INPUT] key. Remote G DEF.
Page 49
4.7.4.3 DEFLECTION ADJUSTMENT Measuring Item Test point Adjustment part Description instrument V. POSITION / Signal [1.PICTURE/SOUND] • To memorize every time after finish adjustment on each SIZE / generator D01 : V. SIZE mode. LINEARITY D05 : V. LINE (1) Receive NTSC circle pattern signal. adjustment Remote D06 : V.
Page 50
Measuring Item Test point Adjustment part Description instrument SIDE PIN Signal [1.PICTURE/SOUND] (1) Receive NTSC crosshatch signal. adjustment generator D02 : EW (2) Select FULL mode with [ASPECT] key. D08 : BOT.CORN (3) Select 1. PICTURE/SOUND from SERVICE MENU. Remote D09 : TOP.CORN (4) Select <...
Page 51
4.7.4.4 CONVERGENCE ADJUSTMENT Measuring Item Test point Adjustment part Description instrument CONVERGENCE Signal [6.CONVER A] NOTE: PHASE generator CPA04 : TPOV OFST Be sure to make it the value of Table1. Supposing data [check] CPA05 : FINEP differs, correct to the value of Table1. Remote CPA06 : STARTLIN A When data is corrected (when the [MUTING] key is...
Page 52
Measuring Item Test point Adjustment part Description instrument OVERALL Signal [ 6.CONVER A ] NOTE: CONVERGENCE generator CPA01 : FINE OFF Be sure to make it the value of Table2. Supposing data (LINE) CCA01 : H CENT differs, correct to the value of Table2. [check] Remote CCA02 : H SIZE...
Page 53
Measuring Item Test point Adjustment part Description instrument OVERALL Signal [ 7.CONVER B ] NOTE: CONVERGENCE generator Perform this adjustment after performing OVERALL (POINT) CONVERGENCE (LINE) check. adjustment Remote It adjusts displaying and checking adjustment data by control unit the [DISPLAY] key. Adjust in order of Area A, Area B, Area C and Area D.
Page 54
Measuring Item Test point Adjustment part Description instrument AUTO Signal AUTO CONVERGENCE (SUPER FOCUS) PRESET CONVERGENCE generator AUTO CONVERGENCE PRESET is a work in which you (SUPER FOCUS) store (memorize) an optimum reference CONVERGENCE setting Remote in SUPER FOCUS operation in the unit. At the factory, this control unit PRESET has been carried out and memorized in the unit after adjusting CONVERGENCE.
Page 55
4.7.5 VIDEO ADJUSTMENT Measuring Item Test point Adjustment part Description instrument RGB CUTOFF Signal TP-R [1.PICTURE/SOUND] (1) Receive NTSC signal (include 0% or -3% black). adjustment generator [R CRT S14: CUTOF R (2) Select STANDARD mode with [VIDEO STATUS] SOCKET PWB] S16: CUTOF G key.
Page 56
Measuring Item Test point Adjustment part Description instrument WHITE Signal [3.WHITE BALANCE] NOTE : Before starting the adjustment, warm up the unit for BALANCE generator more than 30 minutes. (LOW LIGHT) CUT R (1) Receive NTSC gray scale signal (include 0% black). adjustment Remote CUT B...
Page 57
Measuring Item Test point Adjustment part Description instrument SUB BRIGHT Signal [1.PICTURE/SOUND] (1) Receive NTSC signal (include 0% or -2% black). adjustment generator S03: BRIGHT (2) Select STANDARD mode with [VIDEO STATUS] key. (3) Set the COLOR TEMP is LOW mode. Remote (4) Select 1.PICTURE/SOUND from SERVICE MENU.
Page 58
Measuring Item Test point Adjustment part Description instrument SUB COLOR / Signal TP-R [1.PICTURE/SOUND] [ Method of adjustment without measuring instrument ] SUB TINT / generator [R CRT S01 : COLOR (1) Receive NTSC color bar signal (include 75% white). B-Y GAIN SOCKET PWB] S02 : TINT...
Page 59
Measuring Item Test point Adjustment part Description instrument SUB COLOR / Signal TP-R [1.PICTURE/SOUND] [ Method of adjustment with measuring instrument ] SUB TINT / generator [R CRT S01 : COLOR (1) Receive NTSC color bar signal (include 75% white). B-Y GAIN SOCKET PWB] S02 : TINT...
Page 60
4.7.6 AUDIO (MTS) ADJUSTMENT Measuring Item Test point Adjustment part Description instrument MTS INPUT Remote [1.PICTURE/SOUND] (1) Select 1.PICTURE / SOUND from SERVICE MENU. LEVEL control unit A01 : IN LEVEL (2) Select < A01 > (IN LEVEL). check (3) Verify that < A01 > is set at its initial setting value. TV audio AUDIO OUT [1.PICTURE/SOUND]...
SECTION 5 TROUBLESHOOTING SELF-DIAGNOSIS FUNCTIONS • This model has self-check functions that inform of the failure of the TV by detecting abnormality. • Operational state is always monitored and the identified is memorized on the record. Therefore, diagnosis may be prevented against expectations if "NG" are indicated in many items. When recurrence of symptoms can be predicted, erase (reset) the history of failure and allow the unit to again record the results of diagnosis.
Page 62
Indication Check item Details of detection Method of detection SYNC Presence or absence of Presence of synchronized signal. When entering the self-check mode, "OK" is synchronized signal HD : Component signal shown. M : NTSC main signal While running the mode with picture signal, if S : NTSC sub signal the synchronized signal is disappeared, "NG"...
Page 63
JVC SERVICE & ENGINEERING COMPANY OF AMERICA DIVISION OF JVC AMERICAS CORP. www.jvcservice.com(US Only) JVC CANADA INC. Head office : 21 Finchdene Square Scarborough, Ontario M1X 1A7 (416)293-1311 (No.YA091) Printed in Japan...
Page 64
PARTS LIST CAUTION The parts identified by the symbol are important for the safety . Whenever replacing these parts, be sure to use specified ones to secure the safety. The parts not indicated in this Parts List and those which are filled with lines --- in the Parts No. columns will not be supplied. P.W.
Page 65
CONTENTS USING P.W. BOARD & REMOTE CONTROL UNIT ..........................3-2 EXPLODED VIEW PARTS LIST ................................3-3 EXPLODED VIEW ....................................3-5 PRINTED WIRING BOARD PARTS LIST [AV-48P575/H] ........................3-7 MAIN P.W. BOARD ASS'Y (SRP-1003A-M2) ..........................3-7 DEF / CONVERGENCE OUT P.W. BOARD ASS'Y (SRP-2002A-M2) ..................3-11 R CRT SOCKET P.W. BOARD ASS'Y (SRP-3101A-M2) ......................3-14 G CRT SOCKET P.W.
KNOB AV-48P575/H,AV-56P575/H LC21576-002C-A KNOB AV-56P585/H LC32555-001C-A LED LENS QYSBSF3012M TAP SCREW 3.0mm x 12mm(x2) LC32412-001A-C JVC MARK QYNSS3000P PUSH NUT LC21490-001A-A SHADING BOARD QAS0248-001 SPEAKER SP01/SP02(x2) QYSBSA4012M TAP SCREW M4 x 12mm(x8) LC32645-001A-A BC FIT...
Page 67
Ref.No. Part No. Part Name Description Local 100 LC21639-001B-A CONTROL ASSY Inc.No.101-106 AV-48P575/H,AV-56P575/H 100 LC21639-002B-A CONTROL ASSY Inc.No.101-106 AV-56P585/H 101 LC11788-001C-A CONTROL BASE AV-48P575/H,AV-56P575/H 101 LC11788-002C-A CONTROL BASE AV-56P585/H 102 LC11786-001C-A DOOR AV-48P575/H,AV-56P575/H 102 LC11786-002C-A DOOR AV-56P585/H...
PRINTED WIRING BOARD PARTS LIST [AV-48P575 MAIN P.W. BOARD ASS'Y (SRP-1003A-M2) Ref No. Part No. Part Name Description Local Ref No. Part No. Part Name Description Local D1401 MA111-X SI DIODE D1402 UDZS5.1B-X Z DIODE IC1101 L7805CP D1403 MA111-X SI DIODE IC1140 CXA2205Q-X D1513...
Page 71
Ref No. Part No. Part Name Description Local Ref No. Part No. Part Name Description Local C1169 QENC1HM-475Z BP E CAPACITOR 4.7uF 50V M C1652 NCB31CK-153X C CAPACITOR 0.015uF 16V K C1170 QENC1HM-475Z BP E CAPACITOR 4.7uF 50V M C1653 NCB31CK-473X C CAPACITOR 0.047uF 16V K...
Page 72
Ref No. Part No. Part Name Description Local Ref No. Part No. Part Name Description Local C3023 NCF31CZ-104X C CAPACITOR 0.1uF 16V Z C3024 NCF31CZ-104X C CAPACITOR 0.1uF 16V Z R0705 NRSA63J-103X MG RESISTOR 10kΩ 1/16W J C3025 QETN1CM-106Z E CAPACITOR 10uF 16V M R0706 NRSA63J-103X...
Page 73
Ref No. Part No. Part Name Description Local Ref No. Part No. Part Name Description Local R1525 NRSA63J-682X MG RESISTOR 6.8kΩ 1/16W J R1971 QRT039J-R68 MF RESISTOR 0.68Ω 3W J R1526 NRSA63J-682X MG RESISTOR 6.8kΩ 1/16W J R1975 NRSA63J-102X MG RESISTOR 1kΩ...
Ref No. Part No. Part Name Description Local Ref No. Part No. Part Name Description Local R3532 NRSA63J-680X MG RESISTOR 68Ω 1/16W J LC3008 NQR0470-001X EMI FILTER 22pF 50V +50%-20% R3534 NRSA63J-101X MG RESISTOR 100Ω 1/16W J LC3501 NQR0470-003X EMI FILTER 100pF 50V +50%-20% R3535 NRSA63J-182X...
Page 75
Ref No. Part No. Part Name Description Local Ref No. Part No. Part Name Description Local D846 RD6.8E/B2/-T2 Z DIODE C523 QFN32AJ-682Z M CAPACITOR 6800pF 100V J D847 RD6.8E/B2/-T2 Z DIODE C524 QCS31HJ-470Z C CAPACITOR 47pF 50V J D850 RD5.6E/B2/-T2 Z DIODE C525 QCB31HK-682Z...
Ref No. Part No. Part Name Description Local Ref No. Part No. Part Name Description Local R184 NRSA63D-473X MG RESISTOR 47kΩ 1/16W D R835 NRSA63J-473X MG RESISTOR 47kΩ 1/16W J R185 NRSA63D-183X MG RESISTOR 18kΩ 1/16W D R836 NRSA63J-473X MG RESISTOR 47kΩ...
B CRT SOCKET P.W. BOARD ASS'Y (SRP-3301A-M2) Ref No. Part No. Part Name Description Local Ref No. Part No. Part Name Description Local D1006 RM2C-LFA1 SI DIODE IC3001 TDA6111Q D1101 EU01N-T2 SI DIODE D1102 MA8150/M/-X Z DIODE Q3031 2SA1037AK/QR/-X TRANSISTOR C1002 QETN2EM-106Z E CAPACITOR...
Ref No. Part No. Part Name Description Local Ref No. Part No. Part Name Description Local R7110 QRJ146J-681X UNF C RESISTOR 680Ω 1/4W J D981 MA111-X SI DIODE R7111 QRE121J-473Y C RESISTOR 47kΩ 1/2W J D983 1SR35-400A-T2 SI DIODE R7112 QRE121J-473Y C RESISTOR 47kΩ...
DIGITAL INPUT MODULE P.W. BOARD ASS'Y Ref No. Part No. Part Name Description Local (SRP-7803A-M2) CN008 QGB1506L1-16 CONNECTOR B-B (1-16) Ref No. Part No. Part Name Description Local ICP-N70-T IC PROTECTOR 2.5A CP934 CP936 ICP-N70-T IC PROTECTOR 2.5A ICP-N70-T IC PROTECTOR 2.5A CP941 MD001...
PRINTED WIRING BOARD PARTS LIST [AV-56P575 MAIN P.W. BOARD ASS'Y (SRP-1004A-M2) Ref No. Part No. Part Name Description Local Ref No. Part No. Part Name Description Local D1401 MA111-X SI DIODE D1402 UDZS5.1B-X Z DIODE IC1101 L7805CP D1403 MA111-X SI DIODE IC1140 CXA2205Q-X D1513...
Page 81
Ref No. Part No. Part Name Description Local Ref No. Part No. Part Name Description Local C1169 QENC1HM-475Z BP E CAPACITOR 4.7uF 50V M C1652 NCB31CK-153X C CAPACITOR 0.015uF 16V K C1170 QENC1HM-475Z BP E CAPACITOR 4.7uF 50V M C1653 NCB31CK-473X C CAPACITOR 0.047uF 16V K...
Page 82
Ref No. Part No. Part Name Description Local Ref No. Part No. Part Name Description Local C3023 NCF31CZ-104X C CAPACITOR 0.1uF 16V Z C3024 NCF31CZ-104X C CAPACITOR 0.1uF 16V Z R0705 NRSA63J-103X MG RESISTOR 10kΩ 1/16W J C3025 QETN1CM-106Z E CAPACITOR 10uF 16V M R0706 NRSA63J-103X...
Page 83
Ref No. Part No. Part Name Description Local Ref No. Part No. Part Name Description Local R1525 NRSA63J-682X MG RESISTOR 6.8kΩ 1/16W J R1971 QRT039J-R68 MF RESISTOR 0.68Ω 3W J R1526 NRSA63J-682X MG RESISTOR 6.8kΩ 1/16W J R1975 NRSA63J-102X MG RESISTOR 1kΩ...
PRINTED WIRING BOARD PARTS LIST [AV-56P585 MAIN P.W. BOARD ASS'Y (SRP-1002A-M2) Ref No. Part No. Part Name Description Local Ref No. Part No. Part Name Description Local D1401 MA111-X SI DIODE D1402 UDZS5.1B-X Z DIODE IC1101 L7805CP D1403 MA111-X SI DIODE IC1140 CXA2205Q-X D1513...
Page 86
Ref No. Part No. Part Name Description Local Ref No. Part No. Part Name Description Local C1169 QENC1HM-475Z BP E CAPACITOR 4.7uF 50V M C1652 NCB31CK-153X C CAPACITOR 0.015uF 16V K C1170 QENC1HM-475Z BP E CAPACITOR 4.7uF 50V M C1653 NCB31CK-473X C CAPACITOR 0.047uF 16V K...
Page 87
Ref No. Part No. Part Name Description Local Ref No. Part No. Part Name Description Local C3023 NCF31CZ-104X C CAPACITOR 0.1uF 16V Z C3024 NCF31CZ-104X C CAPACITOR 0.1uF 16V Z R0705 NRSA63J-103X MG RESISTOR 10kΩ 1/16W J C3025 QETN1CM-106Z E CAPACITOR 10uF 16V M R0706 NRSA63J-103X...
Page 88
Ref No. Part No. Part Name Description Local Ref No. Part No. Part Name Description Local R1525 NRSA63J-682X MG RESISTOR 6.8kΩ 1/16W J R1971 QRT039J-R68 MF RESISTOR 0.68Ω 3W J R1526 NRSA63J-682X MG RESISTOR 6.8kΩ 1/16W J R1975 NRSA63J-102X MG RESISTOR 1kΩ...
REMOTE CONTROL UNIT PARTS LIST (RM-C1257G-1H) Ref No. Part No. Part Name Description Local UR77EC0603 BATTERY COVER PACKING 11 12 13 14 PACKING PARTS LIST Ref.No. Part No. Part Name Description Local LC11253-004A-A PACKING CASE (TOP) AV-48P575/H LC11253-005A-A PACKING CASE (TOP) AV-56P575/H,AV-56P585/H LC31759-001C-A...
Page 92
AV-48P575 AV-56P575 AV-56P585 STANDARD CIRCUIT DIAGRAM NOTE ON USING CIRCUIT DIAGRAMS 1.SAFETY Type No indication : Ceramic capacitor The components identified by the symbol and shading are : Metalized mylar capacitor critical for safety. For continued safety replace safety ciritical : Polypropylene capacitor components only with manufactures recommended parts.
Page 93
CONTENTS SEMICONDUCTOR SHAPES ..............2-2 BLOCK DIAGRAM ..................2-3 CIRCUIT DIAGRAMS ..................2-5 MAIN PWB CIRCUIT DIAGRAM ........................ 2-5 R CRT SOCKET PWB CIRCUIT DIAGRAM ....................2-23 G CRT SOCKET PWB CIRCUIT DIAGRAM ..................... 2-25 B CRT SOCKET PWB CIRCUIT DIAGRAM ....................2-27 VM PWB CIRCUIT DIAGRAM ........................
BLOCK DIAGRAM SPEAKER (L) TU1101 DECODE VTV1 U/V TUNER AUDIO SPEAKER (R) CONTROL IC1140 MTSDECODE /AUDIO SELECT /AUDIO CONTROL CENTER INPUT C_SWMAIN AUDIO IC6001 AUDIO L/R IC1641 IC1661 OUT (FIX) A.H.S AUDIO AMP Y IN TV-V1 SEP. IC1501 AV SELECTOR MULTI C IN COLOR...
Page 95
R CRT SOCKET PWB MI-COM & DIST MODULE PWB IC1101 R OUT IC1001 AD Y IC1002 AD PR DRAM AD PB CONVERTER IC1003 SEP. DATA IC2101 DRAM LATE G OUT CONVERT MULTI MAIN COLOR DEMOD G CRT IC3001 SOCKET PWB DIGITAL MAIN/SUB 3D YC SEP ENHANCE...
CIRCUIT DIAGRAMS MAIN PWB CIRCUIT DIAGRAM (1/9) SHEET1 TU1101- 17 C1111 TU1101 TU1101 QAU0352-001 QAU0352-001 R1152 R1151 R1150 3.9k OPEN D1101 TV_V1 OPEN C1167 R1149 D1102 3.3k CN1E11 C1103 C1172 OPEN C1166 OPEN D1140 OPEN C1163 D1141 .0027 OPEN TV_A CN10E1 SDA0 OPEN...
Page 97
MODE DC ( V ) PIN NO. TU1101 NOT USED CN11S4 CN10S4 OPEN QGA2501C5-03Z R1157 R1158 R1155 R1156 OPEN OPEN D1146 D1143 MA8082/M/-X OPEN D1144 R1150 OPEN 34.1 OPEN D1145 MA8082/M/-X R1149 3.3k CN10DC QJB003-043014 IC1101 C1163 .0027 DIGITAL INPUT MODULE C1162 IC1140 C0701...
Page 101
MODE DC ( V ) PIN NO. IC1501 FRONT CONTROL PWB SHEET 17 CN101H QGA2501C1-11 CN100H OPEN R1501 SCL0 R1502 SDA0 SUR_EFCT SUR_MONO D1591 OPEN SUR_SW D1592 BBE_SW OPEN NOT USED R1511 D1513 IC1502 3.3k MA111-X M62320FP-X S4_DET Q1511 AFT2 R1510 OPEN HP_MU...
Page 107
MODE DC ( V ) PIN NO. IC1211 FRONT CONTROL PWB SHEET 17 CN101G QGA2501C1-10 CN100G 575/H OPEN BASS_MU HP_VOL 575/H MECA_SW REMO STBVCC 585/H ON_TIM POW_LED BS_5V BS_5V STB3.3V STB3.3V STB_GND NOT USED STB_GND EE_CDS C1853 D1851 OPEN OPEN KEY1 CF1851 OPEN...
Page 108
MAIN PWB CIRCUIT DIAGRAM (7/9) SHEET 7 MAIN PWB ASS'Y (7/9) SRP-1003A-M2: AV-48P575/H SRP-1004A-M2: AV-56P575/H SRP-1002A-M2: AV-56P585/H CN1GN1 CN1GN2 OPEN OPEN BS_8V SHEET 9 BS_8V C1444 C1408 OPEN OPEN C1445 OPEN BS_5V SHEET 3, 6, 8, 9 BS_5V SHEET 1, 9 C1412 AUDIO_L AUDIO_L...
Page 109
MODE MODE DC ( V ) DC ( V ) PIN NO. PIN NO. NOT USED CN1004 CN10S3 QGA2501C5-03Z SHEET 1, 6, 8, 9 SHEET 6 NECK CN1003 QGB1506L1-16 SCL0 SCL0 SDA0 C1442 R1421 34.2 SDA0 R1423 3.3k D1403 B1_POW MA111-X B1_POW NECK...
Page 110
MAIN PWB CIRCUIT DIAGRAM (8/9) SHEET 8 R6013 OPEN R6010 OPEN IC1621 OPEN C6002 C6001 R1629 C1630 C1623 OPEN OPEN OPEN R1628 OPEN C1624 OPEN C1621 IC6001 OPEN R1621 C1631 R1622 OPEN R1631 OPEN NJM2701M-X OPEN OPEN AUDIO_L C1632 AUDIO_L OPEN R1640 C1626...
Page 111
MODE DC ( V ) PIN NO. IC6001 C1646 C1645 C6003 R1618 OPEN C1642 C1643 C6004 0.015 0.047 R1641 C1641 C1647 R1642 R1643 R6001 R6002 IC1641 IC1641 NJM2150AM-X C6009 R1651 R1645 R1652 R1653 OPEN C1651 C1652 C1653 0.047 0.015 R1644 OPEN R1649 C1648...
Page 112
MAIN PWB CIRCUIT DIAGRAM (9/9) SHEET 9 POWER PWB SHEET 16 NOT USED CN1001 CN100F QGB1506L1-16 OPEN Y1820 Y1821 OPEN Y1819 OPEN IC1991 D1952 PQ12RD11 OPEN H1991 OPEN R1960 OPEN R1971 QRT039J-R68 D1991 MA111-X R1993 R1991 D1992 OPEN OPEN R1992 Y1952 C1991 1.8k...
Page 113
MODE MAIN PWB ASS'Y (9/9) DC ( V ) PIN NO. IC1511 SRP-1003A-M2: AV-48P575/H NOT USED SRP-1004A-M2: AV-56P575/H CN100F SRP-1002A-M2: AV-56P585/H IC1802 OPEN 13.2 IC1941 29.2 R1801 OPEN SHEET 1, 7 SHEET 6 STBVCC IC1942 D1802 MA111-X SHEET 7 LB_PRO 28.9 H1802 IC1802...
POWER PWB CIRCUIT DIAGRAM SHEET 16 MODE DC ( V ) PIN NO. OPEN CN90E1 IC921 NOT USED 141.2 D811 D812 PC811 OPEN OPEN 51.6 T811 LF802 OPEN QQR1407-001 C811 R801 OPEN Y801 2.7M QRZ9041-275 D813 D814 -0.2 F801 OPEN OPEN C804 QMF61U1-7R0-S...
CHANNEL CHART (CA) MODE CHANNEL MODE CHANNEL TUNER TUNER BAND BAND BAND BAND CATV REAL DISP. CATV REAL DISP. W+35 W+36 W+37 W+38 W+39 W+40 W+41 W+42 W+43 W+44 W+45 W+46 W+47 W+48 W+49 W+50 W+51 W+52 W+53 W+54 W+55 W+56 W+57 W+58...
Page 146
JVC SERVICE & ENGINEERING COMPANY OF AMERICA DIVISION OF JVC AMERICAS CORP. www.jvcservice.com(US Only) JVC CANADA INC. Head office : 21 Finchdene Square Scarborough, Ontario M1X 1A7 (416)293-1311 (No.YA091) Printed in Japan...