Specifications - DeWalt DWE7485 Instruction Manual

English
Saw Blades
Do not use saw blades that do not conform to the dimensions stated in the specifications.
•
Do not use any spacers to make a blade fit onto the spindle. Use only the blades specified in this
manual, complying with EN847-1, if intended for wood and similar materials.
• Consider applying specially designed noise-reduction blades.
• Do not use high steel (HS) saw blades.
• Do not use cracked or damaged saw blades.
• Ensure that the chosen saw blade is suitable for the material to be cut.
• Always wear gloves for handling saw blades and rough material. Saw blades should be carried in
a holder wherever practicable.
Additional Safety Information

WARNING: Never modify the power tool or any part of it. Damage or personal injury
could result.

WARNING: ALWAYS use safety glasses. Everyday eyeglasses are NOT safety glasses. Also use
face or dust mask if operation is dusty. ALL USERS AND BYSTANDERS MUST ALWAYS WEAR
CERTIFIED SAFETY EQUIPMENT:
• ANSI Z87.1 eye protection (CAN/CSA Z94.3),
• ANSI S12.6 (S3.19) hearing protection,
• NIOSH/OSHA/MSHA respiratory protection.

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other
construction activities contains chemicals known to the State of California to cause cancer,
birth defects or other reproductive harm. Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work.
To reduce your exposure to these chemicals: work in a well ventilated area, and work with
approved safety equipment, such as those dust masks that are specially designed to filter out
microscopic particles.
Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and
•
other construction activities. Wear protective clothing and wash exposed areas with
soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote
absorption of harmful chemicals.

WARNING: Use of this tool can generate and/or disperse dust, which may cause serious
and permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory
protection appropriate for the dust exposure. Direct particles away from face and body.

WARNING: Always wear proper personal hearing protection that conforms to ANSI
S12.6 (S3.19) during use. Under some conditions and duration of use, noise from this
product may contribute to hearing loss.
• Air vents often cover moving parts and should be avoided. Loose clothes, jewelry or long
hair can be caught in moving parts.
• An extension cord must have adequate wire size (AWG or American Wire Gauge) for
safety. The smaller the gauge number of the wire, the greater the capacity of the cable, that is,
16 gauge has more capacity than 18 gauge. An undersized cord will cause a drop in line voltage
resulting in loss of power and overheating. When using more than one extension to make up
the total length, be sure each individual extension contains at least the minimum wire size. The
following table shows the correct size to use depending on cord length and nameplate ampere
rating. If in doubt, use the next heavier gauge. The lower the gauge number, the heavier the cord.
Minimum gauge for Cord sets
Total length of Cord in Feet
Volts
120V 25 (7.6)
240V 50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4)
Ampere Rating
More not
Than More
Than
0 6 18
6 10 18
10 12 16
12 16 14
The label on your tool may include the following symbols. The symbols and their definitions are
as follows:
V ......................... volts
Hz ....................... hertz
min ..................... minutes
or DC ...... direct current
...................... Class I Construction (grounded)
.../min .............. per minute
BPM .................... beats per minute
IPM ..................... impacts per minute
RPM .................... revolutions per minute
4
(meters)
50 (15.2) 100 (30.5) 150 (45.7)
American Wire gauge
16 16 14
16 14 12
16 14 12
12 Not Recommended
sfpm ................... surface feet per minute
SPM .................... strokes per minute
OPM .................... oscillations per minute
A ......................... amperes
W ........................ watts
or AC ........... alternating current
or AC/DC .... alternating or direct current
...................... Class II Construction (double insulated)
n o ....................... no load speed
n ......................... rated speed
...................... earthing terminal
..................... safety alert symbol
..................... visible radiation
..................... avoid staring at light
Motor
Be sure your power supply agrees with the nameplate marking. Voltage decrease of more than
10% will cause loss of power and overheating. These tools are factory tested; if this tool does not
operate, check power supply.

Specifications

Table Size
Miter Angle
Bevel Angle
Blade Size
Max. Cut Depth, 0° Bevel
Max. Cut Depth, 45° Bevel
RPM, no load
Unpacking (Fig. B)

WARNING: To reduce the risk of injury, DO NOT connect the machine to the power source
until the table saw is completely assembled and you have read the entire instruction manual.
Open the box and slide the saw out using the carrying handle
Fig. B
22
Carefully unpack the table saw and all loose items from the carton. Examine all parts to make sure
that parts have not been damaged during shipping. If any parts are missing or damaged, contact
your dealer to replace them before attempting to assemble the tool.
COMPONENTS (FIG. A)

WARNING: Never modify the power tool or any part of it. Damage or personal injury
could result.
Refer to Figure A at the beginning of this manual for a complete list of components.
Intended Use
This table saw is intended for use by construction professionals for use in ripping, crosscutting,
mitering, beveling and non-through cutting applications in wood, plastic, and other
soft materials.
DO nOT use for cutting metal, cement board, or masonry.
DO nOT use dado sets, multiple blades or shaping cutter heads on this saw.
DO nOT perform tapered cuts without a tapered jig accessory.
DO nOT use the saw for plunge or cove cutting.
DO nOT use under wet conditions or in presence of flammable liquids or gases.
DO nOT let children come into contact with the tool. Supervision is required when inexperienced
operators use this tool.
ASSEMBLY

WARNING: Shock Hazard. To reduce the risk of serious personal injury, turn unit off
and disconnect machine from power source before attempting to move it, change
accessories or make any adjustments. An accidental start-up can cause injury.
Assembly Order (Fig. A)
1. Unlock and remove the throat plate 15
2. Make sure blade is installed correctly and arbor nut is tight. Use wrenches
tool. Refer to Figure A.
3. Position the blade guard assembly 11 .
4. Attach anti-kickback assembly 12 to the guard assembly.
5. Install and lock throat plate 15 . (nOTE: Adjust leveling screws before proceeding. Refer to
Installing the Throat Plate.)
6. Attach the rip fence 16 . (nOTE: Adjust rip scale before proceeding. Refer to Adjusting the
Rip Scale.)
..................... wear respiratory protection
..................... wear eye protection
..................... wear hearing protection
..................... read all documentation
IPXX .................... IP symbol
19 X 19" (485 x 485 mm)
30° left and right
-2° to 47° left
8–1/4" (210 mm)
2–9/16" (65 mm)
1–3/4" (45 mm)
5800
22 , as shown in Figure B.
. Refer to: Removing the Throat Plate section.
19 stored on the