Advertisement
Quick Links
Items Supplied >
1 – INTAKE COVER W/ SCREEN / RING ASSEMBLY
1 – K&N® VENTURI AIR FILTER
1 – BILLET VELOCITY STACK
1 – MOUNTING PLATE
1 – SUPPORT BRACKET
1 – BOLT, M5 X 12mm, ALLEN
2 – BOLT, M6 X 16mm, ALLEN
3 – BOLT, M6 X 25mm, ALLEN
2 – BOLT, M6 X 12mm BUTTONHEAD
4 – BOLT, 1/4"-20 X 1/2", BUTTONHEAD
3 – WASHER, INTERNAL TOOTH LOCK
1 – O-RING, 2.88 "I.D. X .125", BUNA-N
1 – BILLET BREATHER FILTER
Instruction Manual >
Read all instructions carefully and completely before installing your new POWRFLO
1.
Remove the (4) bolts that hold on the stock air cleaner cover. Once the cover has been removed, loosen
the top bolt to remove the filter from air box.
2.
Remove the air box by loosening the (5) allen bolts around the air inlet and the (2) hex bolts from the lower
portion of the air box. See Figure 1. Disconnect the (2) hoses, idle adjuster and air temperature sensor
connector from the air box.
3.
Once the air box has been removed, unscrew the air temperature sensor and install it into the supplied
mounting plate using the supplied M5 bolt, refer to Figure 3. NOTE: Make sure the small stock o-ring
around the sensor is still intact.
4.
Install the supplied billet breather filter into the upper hose (disconnected in Step 2) and clamp. Rotate the
hose so the billet breather filter is pointed to the rear and resting slightly on top of the throttle body.
5.
Insert the supplied o-ring into the groove of the supplied velocity stack. NOTE: Do not attempt to stretch the
o-ring into groove; position o-ring evenly around groove and use gentle force (No tools) to push it in.
6.
Bolt the velocity stack to the throttle body using the (2) supplied M6 x 16mm allen bolts and tighten. See
Figure 2.
REMOVE (5) ALLEN BOLTS
(2 LOWER BOLTS ARE HIDDEN IN DIAGRAM)
FIGURE 1
* Cobra
recommends you always wear a helmet while riding. Ple ase never operate your motorcycle while under
®
the influence of alcohol and/or drugs. Enjoy the new look of your motorcycle and please ride safely.
DOCUMENT NO. 0017
REV. A
04/17
23801 E. La Palma Ave., Yorba Linda, Ca 92887 Ph. 714.692.8180, Fax. 714.692.5016
®
VELOCITY
(2) SUPPLIED M6 X 16mm
REMOVE (2) HEX
BOLTS
1
Application(s) >
KAWASAKI VN900
06-0467 - 01 / 02 / 03 / 04
STACK
ALLEN BOLTS
FIGURE 2
www.cobrausa.com
2006 - 2019
Page 1 of 2
TM
Intake.
O-RING
(ACTUALLY ROUND)
®
Advertisement
Related Manuals for Cobra PowrFlo 06-0467-01
Summary of Contents for Cobra PowrFlo 06-0467-01
- Page 1 FIGURE 2 FIGURE 1 BOLTS * Cobra recommends you always wear a helmet while riding. Ple ase never operate your motorcycle while under ® the influence of alcohol and/or drugs. Enjoy the new look of your motorcycle and please ride safely.
- Page 2 23801 E. La Palma Ave., Yorba Linda, Ca 92887 Ph. 714.692.8180, Fax. 714.692.5016 ® www.cobrausa.com Instruction Manual > 06-0467 - 01 / 02 / 03 / 04 Page 2 of 2 Position the mounting plate over the velocity stack (with the welded tube toward inside) and secure using (3) supplied M6 x 25mm buttonhead bolts and (3) internal tooth lock washers, finger tighten only, Figure 3.