Related Manuals for ZyXEL Communications ADSL2+ Ethernet / USB Router P-660RU-Tx v2
Summary of Contents for ZyXEL Communications ADSL2+ Ethernet / USB Router P-660RU-Tx v2
-
Page 1: Quick Start Guide
P-660RU-Tx v2 ADSL2+ Ethernet / USB Router Quick Start Guide Version 3.40 Edition 3 5/2008... - Page 2 P-660RU-Tx v2 Quick Start Guide Overview The P-660RU-Tx v2 is an ADSL router with both USB and Ethernet ports. See your User’s Guide for background information on all features. This Quick Start Guide shows you how to: • Connect the hardware. •...
-
Page 3: Hardware Connections
P-660RU-Tx v2 Quick Start Guide 1 Hardware Connections There are two ways to connect your computer or computer network to the P-660RU-Tx v2: Option A: Connect via Ethernet. See Option B: Connect via USB (you will need to install the USB driver). - Page 4 P-660RU-Tx v2 Quick Start Guide 2 DSL: Use the gray telephone wire to connect your P- 660RU-Tx v2’s DSL port to a telephone jack (or to a splitter, if one is already installed). 3 POWER: Use the power adaptor provided with your P- 660RU-Tx v2 to connect an appropriate power source to the POWER socket.
- Page 5 P-660RU-Tx v2 Quick Start Guide If any of these lights are not on, check your connections and inspect your cables for damage. If the lights are still off, contact your local vendor. Option B: Connect via USB...
- Page 6 P-660RU-Tx v2 Quick Start Guide Do NOT connect the same computer to both the USB and ETHERNET ports on the P-660RU-Tx 1 USB: Connect the provided USB cable to the P-660RU-Tx v2’s USB port. 2 DSL: Use the gray telephone wire to connect your P- 660RU-Tx v2’s DSL port to a telephone jack (or to a splitter, if one is already installed).
-
Page 7: System Requirements
P-660RU-Tx v2 Quick Start Guide If any of these lights are not on, check your connections and inspect your cables for damage. If the lights are still off, contact your local vendor. Install the USB Software If you want to connect to the Internet through the P-660RU-Tx v2's USB port, install the USB driver before you connect the P-660RU-Tx v2 to the USB port. - Page 8 P-660RU-Tx v2 Quick Start Guide 5 An install warning may appear in the Windows Vista OS. Click Allow to continue. 6 Click Next in the Welcome screen to begin the USB Installation Wizard. Follow the installation prompts. You may need to restart your computer at the end of the installation.
- Page 9 P-660RU-Tx v2 Quick Start Guide Macintosh Computer System Requirements • Macintosh operating system versions 10.1, 10.2 and 10.3. • An available USB port Procedures 1 Save your work and close all applications. 2 Insert the included CD. A CD’s icon automatically displays on the desktop.
- Page 10 P-660RU-Tx v2 Quick Start Guide 5 Double-click one of the following. If you selected MAC10.1, double click the P-660RU-T icon. If you selected MAC 10.2_10.3, double click the P-660RU- Tx.dmg icon.
- Page 11 P-660RU-Tx v2 Quick Start Guide 6 Click Continue in the Welcome screen to begin the USB installation. Follow the installation prompts. You may need to restart your computer at the end of the installation. 2 Connection Setup: Automatic Use this section to have your P-660RU-Tx v2 automatically detect and set up your Internet connection.
- Page 12 P-660RU-Tx v2 Quick Start Guide connection test screen similar to the following, go to step 5. 3 If the connection test is successful, the following screen appears. Your Internet connection is ready for you to use. 4 If the connection test is not successful, you may see a screen similar to the following.
-
Page 13: Connection Setup: Wizard
P-660RU-Tx v2 Quick Start Guide 5 If the connection test is not successful, check your connections and restart the P-660RU-Tx v2. If you still cannot access the Internet, take the steps in the following section. You should have information provided by your Internet Service Provider. - Page 14 P-660RU-Tx v2 Quick Start Guide 3 Type (and retype) a new password and click Apply. You have to use a new password other than the default password 1234, or you cannot apply it successfully. 4 The system asks you to enter your new password to log in again.
- Page 15 P-660RU-Tx v2 Quick Start Guide 5 Select Go to Wizard setup. Click Apply. 6 Click INTERNET SETUP. Wait while your P-660RU-Tx v2 tries to detect your DSL connection.
- Page 16 P-660RU-Tx v2 Quick Start Guide 7 If the connection test is successful, the following screen displays. Click Finish to exit the wizard. 8 If the connection test is not successful, you may see a screen similar to one of the following.
- Page 17 P-660RU-Tx v2 Quick Start Guide Either click Restart the Internet Setup Wizard (if available) to have the ZyXEL Device detect your connection again, or click Next to set up your Internet connection manually. 9 Follow the instructions in the wizard. Enter your Internet connection information exactly as provided by your ISP.
- Page 18 P-660RU-Tx v2 Quick Start Guide 1 Follow steps configurator. 2 Select Go to Advanced setup. Click Apply. 3 The Status screen appears. Click Network > WAN in the navigation panel on the left of the screen. 4 The Internet Connection screen appears. Enter the information exactly as provided by your ISP and click Apply.
- Page 19 P-660RU-Tx v2 Quick Start Guide The fields available in this screen depend on the Mode you select. 5 If you still cannot access the Internet, see Troubleshooting and/or contact your Internet Service Provider (ISP) for assistance.
-
Page 20: Troubleshooting
P-660RU-Tx v2 Quick Start Guide Troubleshooting 1 If you want to verify your USB installation, • Check the status of the P-660RU-Tx v2 in the Device Man- ager window. Click Start > Settings > Control Panel > Sys- tem > Hardware and then click Device Manager. (Steps may vary depending on the version of Windows.) •... - Page 21 P-660RU-Tx v2 Quick Start Guide B) If your ISP gave you Internet connection information, ensure you enter it correctly. For example, if your account has a user name and password, make sure you type it correctly. In addition, if you are not sure which encapsulation your ISP uses, contact your ISP.
- Page 22 P-660RU-Tx v2 Quick Start Guide • Click the wizard icon ( wizard again. Check whether you can access the Inter- net. If you still cannot access the Internet, take the following steps: • If you are using Bridge mode (check Mode in the Net- work >...