Page 2
SGCZ2600DW 25.4 cm APPROVAL NUMBER OF CE EXHAUST EMISSION REGULATION GB-2 EC DECLARATION OF COMFORMITY ZENOAH CO., LTD. 1-9, Minamidai, Kawagoe, Saitama, Japan DIRECTIVE 89/336/EEC, 98/37/EC EN ISO 11806 : 1997 2000 / 14 / EC Internal control production. The products referred are :...
SAFETY FIRST Instructions contained in warnings within this manual marked with a symbol concern critical points which must be taken into consideration to prevent possible serious bodily injury, and for this reason you are requested to read all such instructions carefully and follow them without fail.
SGCZ2600DL 1930 x 250 x 250 Air-cooled 2-stroke gasoline 1.2Hp (0.9kW) at 7500min Mixture (Gasoline 50 : Oil 1) (when using ZENOAH genuine oil) Walbro Diaphragm type Centrifugal clutch, Rigid drive shaft Never modify your machine. We won’t warrant the machine, if you use the remodeled brushcutter or if you don’t observe...
5. For safe operation 1. Read this manual carefully until you completely understand and follow all safety and operating instructions. 2. Keep this manual handy so that you may refer to it later when- ever any questions arise. Also note, if you have any questions which cannot be answered herein, contact the dealer from whom you purchased the prod-...
Page 6
If it continues to rotate even after the throttle has been moved fully back, turn off the engine and take the unit to your authorized ZENOAH servic- ing dealer for repair. USING THE PRODUCT IMPORTANT Cut only materials recommended by the manufacturer.
Page 7
SGCZ2600DL/SGCZ2600DW HANDLING FUEL 1. The engine of the ZENOAH prod- uct is designed to run on a mixed fuel, which contains highly flam- mable gasoline. Never store cans of fuel or refill the tank of the unit...
SGCZ2600DL/SGCZ2600DW 6. Set up <SGCZ2600DL> MOUNTING ENGINE 1. Install the engine to the drive shaft so that the cylin- der head and the stop switch may come on the same side. 2. Using attached four bolts, secure the connection firmly with equal force (Torque: 25in-lbs)(Torque: 2.8 N.m.).
Page 9
6. Set up CUTTERCASE WARNING The blade has very sharp edges. Be sure to use pro- tective gloves whenever handling it. 1. Remove the fastening screw(long) and the lock screw(short) from the cuttercase. 2. While aligning the locking holes, install the cuttercase assembly to the shaft casing.
• The Zenoah engines are lubricated by oil specially formulated for air-cooled 2-cycle gasoline engine use. If Zenoah oil is not available, use an anti-oxidant added quality oil expressly labeled for air-cooled 2-cycle engine use (JASO FC GRADE OIL or ISO EGC GRADE).
8. Operation STARTING ENGINE WARNING The cutting head will start rotating upon the engine starts. 1. Rest the unit on a flat, firm place. Keep the cutting head off the ground and clear of surrounding objects as it will start rotating upon starting of the engine. 2.
Page 12
SGCZ2600DL/SGCZ2600DW 8. Operation ADJUSTING THE MAXIMUM SPEED<SGCZ2600DL> • The screw at the throttle lever is for adjusting the maxi- mum rpm. • Turning the screw crock-wise, the rpm becomes down, the otherwise, the rpm becomes up. (STANDARD OP- ERATION SPEED: 8000 to 9500 rpm) Running engine with faster engine speed than 9500 rpm may damage the engine, slower engine speed than 8000 rpm may cause of the poor cutting ability.
Page 13
8. Operation CUTTING WORK This machine does cutting not by a rotary cutter like con- ventional trimmers but by a pair of special blades that moves round within a limited angle at a speed of ap- proximately 1/30 of conventional trimmers. This unique mechanism has brought you many benefits as follow- ing;...
SGCZ2600DL/SGCZ2600DW 9. Maintenance System/components fuel leaks, fuel spillage fuel tank, air filter, fuel filter idle adjusting screw spark plug cylinder fins, intake air cooling vent muffler, spark arrester, cylinder exhaust port throttle lever, ignition switch cutting parts gear case, cutter case screws/nuts/bolts debris guard •...
Page 15
Clean the spark plug and check that the plug gap is in the correct range. For a re- placement plug, use the correct type specified by ZENOAH. 0.6 to 0.7 mm • REPLACEMENT PLUG IS A NGK CMR7A.
SGCZ2600DL/SGCZ2600DW 9. Maintenance INTAKE AIR COOLING VENT WARNING • Never touch the cylinder, muffler, or spark plugs with your bare hands immediately after stopping the engine. The engine can become very hot when in operation, and doing so could result in severe burns.
(exhaust port) → carbon is built-up air cleaner cylinder fin, fan cover When your unit seems to need further service, please consult with our ZENOAH service shop in your area. Limited warranty Should any failure occur on the product under normal oper-...