Zenith HEALTHVIEW H20J55DT Installation Manual page 47

Zenith crt television user manual
Hide thumbs Also See for HEALTHVIEW H20J55DT:
Table of Contents

Advertisement

Installer Menu
Detailed Descriptions for Installer Menu Items 10-I through 27-I
Change values with ADJ (Adjust) Left/Right keys.
It may be best to set the same value on every TV.
Note: The maximum volume level cannot have a
value setting lower than the MIN VOLUME level
(See Item 8 -I).
10-I. MUTE DISABLE
Enables or disables sound mute function. If set to
1, sound cannot be muted. If set to 0, sound can
be muted.
11-I. NOT USED
12-I. IR BANKS EN (IR Banks Enable)
For direct access to a particular Channel Bank.
When enabled, installer can access a channel bank
by inputting the IR code for the bank.
13-I. SCAN MODE
Allows variation in the On/Off setup with CHANNEL
Up/Down. You may opt for TV channels only or TV
channels + Off/On with the following settings for
Scan Mode. Scan mode Characteristics:
0 = Channel Up/Down keys Change channels only.
1 = Channel Down below the lowest channel (or
channel up higher than the highest channel) and
the TV turns Off.
14-I. STRT CH IN SM (Start Channel in Scan
Mode) If set to 1, installs TV On/Off event below
the start channel at TV turn On.
15-I. SLEEP TIMER
If set to 1, the Sleep Timer feature is available
(but no message is displayed prior to turn-Off).
If set to 0, the Sleep Timer is not functional.
16-I. EN. TIMER (Enable Timer)
If set to 1, On/Off Timer functions are available to
end user. Set to 0 to disable Timer functions.
Note: Clock must be set in order to use Timers.
17-I. ALARM
Gives you the option of making the Alarm function
available to the user. Set to 1, Alarm function is
available to user. Set to 0 to disable the Alarm
function. Note: Clock must be set in order to set
the Alarm.
18-I. NOT USED
206-4065
19-I. NOT USED
20-I. FEATURE LEVEL
Default set to ZEN 1 for Zenith IR remote control
operation. Set O, P LBL for Zenith Private Label IR
remote control operation.
WARNING: Do not change the default value
unless you have the proper remote control
to operate the TV.
21-I. V-CHIP
Set to 1 to activate V-Chip (Parental Control); have
it available to user to filter or control or restrict
programming content. Set to 0 to turn V-Chip fea-
ture Off, not available to user; no programming
restrictions can be set.
22-I. MAX BLK HRS (Maximum Block Hours)
Set 0 to 99 for the maximum V-Chip (Parental
Control) block hours. Default setup is for 12 block-
ing hours.
23-I. CAPTION LOCK
Set to 1 to restore previous Caption On/Off state
after TV turns Off. If set to 0, Captions are always
Off, when TV is initially turned On.
24-I. TEXT MODE
Determines whether TEXT 1, TEXT 2, TEXT 3, or
TEXT 4 decoding is enabled when TEXT is turned on
(either from the Setup Menu or directly with CC on
the remote).
TIP: Set Text Mode to 1 only if text is offered in
your video system.
25-I. NOT USED
26-I. NOT USED
27-I. HOSPITAL MODE
The default is 2 (which favors most hospitals).
With this setting two things are affected: Channel
Banks 1, 2 and 3 are accessible, while Bank 4 is
inactive. Hosp. Mode=0 Not hospital mode. IR code
depends on Item 20-I setting.
"Inactive TV" features not available.
Hosp. Mode= 1 Zenith P.L. IR Code (Bed 1)
Hosp. Mode= 2 Zenith IR Code (Bed 2)
Page 47

Advertisement

Table of Contents
loading

Table of Contents