Related Manuals for Miller Coolmate 1.3 CE
Summary of Contents for Miller Coolmate 1.3 CE
- Page 1 OM-270223E 2018-01 Processes TIG (GTAW) Welding MIG (GMAW) Welding Description Coolmate 1.3 OWNER’S MANUAL For product information, Owner’s Manual translations, and more, visit www.MillerWelds.com...
- Page 2 From Miller to You Thank you and congratulations on choosing Miller. Now you can get the job done and get it done right. We know you don’t have time to do it any other way. That’s why when Niels Miller first started building arc welders in 1929, he made sure his products offered long-lasting value and superior quality.
-
Page 3: Table Of Contents
TABLE OF CONTENTS SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING ....... . . 1-1. - Page 4 DECLARATION OF CONFORMITY for European Community (CE marked) products. ITW Welding Italy S.r.l Via Privata Iseo 6/E, 20098 San Giuliano M.se, (MI) Italy declares that the product(s) identified in this declaration conform to the essent ial requirements and provisions of the stated Council Directive(s) and Standard(s).
-
Page 5: Section 1 − Safety Precautions - Read Before Using
SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING coolers 2018-01 Protect yourself and others from injury — read, follow, and save these important safety precautions and operating instructions. 1-1. Symbol Usage DANGER! − Indicates a hazardous situation which, if Indicates special instructions. -
Page 6: California Proposition 65 Warnings
READ INSTRUCTIONS. HIGH PRESSURE FLUIDS can injure or kill. D Read and follow all labels and the Owner’s D Coolant can be under high pressure. Manual carefully before installing, operating, or D Release pressure before working on cooler. servicing unit. Read the safety information at the beginning of the manual and in each D If ANY fluid is injected into the skin or body seek medical help section. -
Page 7: Section 2 − Definitions
SECTION 2 − DEFINITIONS 2-1. Additional Safety Symbols And Definitions Some symbols are found only on CE products. Warning! Watch Out! There are possible hazards as shown by the symbols. Safe1 2012−05 Do not discard product (where applicable) with general waste. Reuse or recycle Waste Electrical and Electronic Equipment (WEEE) by disposing at a designated collection facility. -
Page 8: Miscellaneous Symbols And Definitions
Plugged filter or hoses can cause overheating to the power source and torch. Safe50 2012−05 100 h. Std. Every 100 hours, check and clean filter and check condition of hoses. Safe51 2012−05 2-2. Miscellaneous Symbols And Definitions Water (Coolant) Amperage Hertz Output Alternating... -
Page 9: Section 3 − Specifications
This equipment will deliver rated output at an ambient air temperature up to 1045F ( 405C). Coolant Tank Maximum Cooling Capacity Capacity Model Input Power Dimensions Weight Coolmate 1.3 CE 1470 Watts Single Phase Length: 620 mm 20 kg (5020 BTU/hr) 115 VAC Height: 320 mm 1.0 L/min... - Page 10 Notes OM-270223 Page 6...
-
Page 11: Section 4 − Installation
SECTION 4 − INSTALLATION 4-1. Selecting a Location Do not move or operate unit where it could tip. Position unit so air can circulate. 500 mm 500 mm 500 mm 956172191_1-A OM-270223 Page 7... -
Page 12: Cooler Mounting Options
4-2. Cooler Mounting Options A. Mounting Cooler To A Small A. Mounting Cooler To A Small Runner Cart Runner Cart Mounting Bracket Kit 028066299 Small Runner Cart − Part No. 300988 − Not Supplied Wrapper Screws Remove screws from wrapper and use screws to secure brackets to machine. - Page 13 C. Mounting Cooler To A Maxstar) 280/Dynasty) 280 C. Mounting Cooler To A Maxstar 280 Or Dynasty 280 Maxstar 280 Or Dynasty 280 − (Not Supplied) Mounting Hardware Remove screws from bottom of power source front and rear panels as shown. Place power source on cooler be- tween the mounting brackets and secure with the just removed hard-...
-
Page 14: Connecting 115 Vac Input Power
4-3. Connecting 115 VAC Input Power Coolmate 1.3 power Receptacle Cooler Power Cord Provides 115 VAC to power cooler. NOTICE − The Coolmate 1.3 is designed only for use with Dynasty) 280 and Maxstar) 280 Models. SECTION 5 − OPERATION 5-1. -
Page 15: Section 6 − Maintenance & Troubleshooting
SECTION 6 − MAINTENANCE & TROUBLESHOOTING 6-1. Routine Maintenance Disconnect power before maintaining. n = Check Z = Change ~ = Clean l = Replace Reference * To be done by Factory Authorized Service Agent Every NOTICE − Clean coolant filter. Severe condi- tions may require more frequent cleaning (con- Months tinuous use, high/low temperatures, dirty envi-... -
Page 16: Flow Direction
6-3. Flow Direction Blue Outlet Flow Filter Inlet Flow Tank Radiator 956172140-A 6-4. Troubleshooting Trouble Remedy Coolant system does not work. Be sure cooler input power and communication cables from power source are connected to cooler receptacles. Check input power line fuses or circuit breaker, and replace or reset if necessary. Have Factory Authorized Service Agent check motor. -
Page 17: Section 7 − Electrical Diagram
SECTION 7 − ELECTRICAL DIAGRAM 956172192-A OM-270223 Page 13... -
Page 18: Section 8 − Parts List
SECTION 8 − PARTS LIST Hardware is common and not available unless listed. 95617219185-A Figure 8-1. Main Assembly, Coolmate 1.3 CE OM-270223 Page 14... - Page 19 Item Dia. Part Mkgs. Description Figure 8-1. Main Assembly, Coolmate 1.3 CE ... . . +116121128 Wrapper ............
- Page 20 Notes...
- Page 21 Notes...
- Page 22 Notes...
- Page 23 Effective January 1, 2018 (Equipment with a serial number preface of MJ or newer) This limited warranty supersedes all previous Miller warranties and is exclusive with no other guarantees or warranties expressed or implied. LIMITED WARRANTY − Subject to the terms and conditions 90 Days —...
- Page 24 File a claim for loss or damage during Phone: 39 (0) 2982901 Fax: 39 (0) 298290-203 shipment. email: miller@itw−welding.it For assistance in filing or settling claims, contact your distributor and/or equipment manufacturer’s Transportation Department. © ORIGINAL INSTRUCTIONS − PRINTED IN USA 2018 Miller Electric Mfg. LLC 2018−01...