Page 1
U C A T HTR-5170 Natural Sound AV Receiver Ampli-tuner audio vidéo V293450 OWNER’S MANUAL MODE D’EMPLOI...
Page 2
Congratulations! You are the proud owner of a Yamaha Digital Sound Field Processing (DSP) System—an extremely sophisticated audio component. The DSP system takes full advantage of Yamaha’s undisputed leadership in the field of digital audio processing to bring you a whole new world of listening experiences. Follow the instructions in this manual carefully when setting up your system, and the DSP system will sonically transform your room into a wide range of listening environments—anything from a...
Using this unit with a higher voltage than specified is dangerous and may result in fire or other accidents. YAMAHA will not be held responsible for any damage resulting from use of this unit with a voltage other than specified.
Dolby Pro Logic Decoder DTS Decoder CINEMA DSP: Theater-like Sound Experience by the Combination of YAMAHA DSP Technology and Dolby Digital, Dolby Pro Logic or DTS Automatic Input Balance Control for Dolby Pro Logic Decoding Test Tone Generator for Easier Speaker...
However, something has still been missing: The atmosphere and acoustic ambiance of the public venue. Our Yamaha engineers have extensively researched the nature of sound acoustics and the way sound reflects inside a room. We sent these engineers to famous theaters and concert halls around the world to measure the acoustics of those venues with sophisticated microphones.
Dolby Digital Dolby Digital is the next level of Dolby Surround sound system developed for 35 mm film-movies by employing low bit-rate audio coding. Dolby Digital is a digital surround sound system that provides completely independent multi-channel audio to you. Dolby Digital provides five full range channels in what is sometimes referred to as a “3/2”...
Dolby Surround theater. For details, refer to pages 48 to 49. However, Yamaha DSP technology allows you to create nearly the same sound experience as that of a large movie theater in your home by compensating for the lack of presence and...
Getting started Unpacking Carefully remove this unit and accessories from the box. You should find the unit itself and the following accessories. Remote controller POWER STANDBY /DTS MOVIE SURROUND THEATER 2 MOVIE TAPE/MD THEATER 1 TUNER MONO MOVIE DISCO DVD/LD TV SPORTS TV/DBS ROCK...
GETTING STARTED Installing batteries in the remote controller Since the remote controller will be used for many of this unit’s control operations, you should begin by installing the supplied batteries. Turn the remote controller over and slide the battery compartment cover in the direction of the arrow. Insert the batteries (AA, R6, UM-3 type) according to the polarity markings on the inside of the battery compartment.
Controls and their functions Front panel NATURAL SOUND AV RECEIVER RX V795aRDS PRESET ROOM 2 STANDBY/ON MEMORY TAPE AUTO TUNING ROOM 2 CONTROL A/B/C/D/E BASS TONE PHONES SPEAKERS EXTENSION BYPASS For the remote controller, refer to pages 61 to 68. STANDBY/ON switch Press this switch to turn on the power.
Page 12
GETTING STARTED A/B/C/D/E button Press this button to select a group (A–E) of preset stations. SPEAKERS switches Press the switch A or B (or both) for the main speakers you will use inward (ON). Press and release the switch for the main speakers you do not use outward (OFF).
Display panel DIGITAL PRO LOGIC MEMORY indicators Either “dts” indicators will be illuminated when the built-in DTS decoder is turned on. A red “dts” indicator will be illuminated when playing a compact disc or laserdisc encoded with DTS. An orange “dts” indicator will be illuminated when playing a DVD encoded with DTS.
If using a SUBWOOFER, such as a Yamaha Active Servo Processing Subwoofer System, the position of the speaker is not so critical because low bass tones are not highly directional.
Speaker system configurations 5 Speaker System The recommended system for enjoying Audio/Video sources. By the use of a center speaker, center channel sounds (dialog, vocals etc.) are precisely localized. 1. CENTER SPEAKER—Set to “LRG” or “SML”. (See page 27.) 4 Speaker System Basic system.
Use RCA type pin plug cables for audio/video units with the exception described later. The output (or input) terminals of YAMAHA audio/video units numbered as 1, 3, 4, etc. on the rear panel must be connected to the same-numbered terminals of this unit.
Page 17
VIDEO AUX terminals (on the front panel) These terminals are used to connect a video input source such as a camcorder. VIDEO AUX VIDEO AUX S VIDEO S VIDEO VIDEO VIDEO L AUDIO R L AUDIO R AUDIO OUT R AUDIO OUT L VIDEO OUT S VIDEO OUT...
Page 18
PREPARATION Connecting to digital (OPTICAL and COAXIAL) terminals If your CD player, LD player, DVD player, TV/satellite tuner, etc. are equipped with coaxial or optical digital audio signal output terminals, they can be connected to this unit’s COAXIAL or OPTICAL, or both terminals. Digital audio signals are transmitted with less loss than analog audio signals.
Page 19
RF demodulator to listen to CD sound without interference. However, if your RF demodulator is the Yamaha model APD-1, you do not have to switch it off. When you want to play an LD source encoded with Dolby Digital without decoding Dolby Digital, you must switch off the power of the RF demodulator.
Page 20
PREPARATION Connecting to S VIDEO terminals If your monitor has an “S” video input terminal and your video cassette recorder, LD player, DVD player, etc. also have “S” video terminals, connect them to this unit’s S VIDEO SIGNAL terminals as illustrated below. In addition, a video unit which has an “S”...
Page 21
Connecting an external decoder of a future format to this unit This unit is equipped with additional 6-channel audio signal input terminals (for left main, right main, center, left rear surround, right rear surround and subwoofer channels) for inputting signals from an external decoder of a future format to this unit.
PREPARATION Speakers Use speakers with the specified impedance shown on the rear of this unit. Subwoofer system Right Main speakers A How to Connect: Connect the SPEAKERS terminals to your speakers with the wire of the proper gauge (keep as short as possible). If the connections are faulty, no sound will be heard from the speakers.
INPUT terminal of the subwoofer amplifier, and connect the speaker terminals of the subwoofer amplifier to the subwoofer. With some subwoofers, including the Yamaha Active Servo Processing Subwoofer System, the amplifier and subwoofer are in the same unit. Such a subwoofer needs only the connection between the SUBWOOFER terminal of this unit and the INPUT terminal of the subwoofer.
Page 24
PREPARATION To drive main, center and/or rear speakers with external amplifiers The speaker connections described on page 20 are fine for most applications. If for some reason, however, you wish to drive main, center and/or rear speakers with your existing amplifier, etc., the following terminals are available for connecting external amplifier(s) to this unit.
Antennas Each antenna should be connected to the designated terminals correctly, as shown in the following figure. Both AM and FM indoor antennas are included with this unit. In general, these antennas will probably provide sufficient signal strength. Nevertheless, a properly installed outdoor antenna will give clearer reception than an indoor one. If you experience poor reception quality only with the indoor antennas, the use of an outdoor antenna may result in improvement.
PREPARATION Connecting the indoor FM antenna Connect the included indoor antenna to the 75Ω UNBAL. FM ANT terminal. Note Do not use an outdoor FM antenna and the indoor FM antenna at the same time. Optional outdoor AM antenna If this unit is placed in steel buildings or an area far from broadcasting stations, it may be necessary to install an outside long wire antenna.
Plugging in this unit • After completing all connections, plug the AC power cord into an AC outlet. REAR (SURROUND) CAUTION MANUAL FOR CORRECT SETTING. (*1) (*1): AC OUTLET(S) (U.S.A., Canada, China, Singapore and General models) ... 2 SWITCHED OUTLETS (Australia model)...
PREPARATION On screen display If you connect your VCR, LD player, video monitor, etc. to this unit, you can take advantage of this unit’s capability to display program titles, parameter data and information for various setting changes and adjustments on your video monitor screen.
Selecting the output modes (“SET MENU” mode) The following functions control the output signals to the speakers in your audio system. When speaker connections are all completed, select a proper position on each function to maximize the performance of your speaker system. * For details about the SET MENU mode, refer to pages 51 to 54.
Page 30
PREPARATION 3. MAIN SPEAKER Choices: LARGE/SMALL Preset position: LARGE LARGE: If your main speakers have a high ability for bass reproduction. In this position, full range signals present at the main channels are output from the main speakers. SMALL: If your main speakers do not have a high ability for bass reproduction.
Page 31
Changing selections Refer to the display panel or the monitor screen when changing the selections. CINEMA DSP NATURAL SOUND AV RECEIVER PRESET ROOM 2 DIGITAL ENHANCED STANDBY/ON MEMORY TAPE MONITOR STEREO NORMAL WIDEPHANTOM DIGITAL AUTO TUNING SPEAKERS SPEAKERS PCM AC—3 ROOM 2 CONTROL PTY HOLD EON NEWS INFO AFFAIRS SPORT...
PREPARATION Speaker balance adjustment This procedure lets you adjust the sound output level balance between the main, center and rear speakers using the built-in test tone generator. After the adjustments, the sound output level heard at the listening position will be the same from each speaker. This is important for the best performance of the digital sound field processor, the Dolby Digital decoder, the Dolby Pro Logic decoder and the DTS decoder.
Page 33
CINEMA DSP NATURAL SOUND AV RECEIVER PRESET ROOM 2 DIGITAL ENHANCED STANDBY/ON MEMORY TAPE MONITOR STEREO NORMAL WIDEPHANTOM DIGITAL PRO LOGIC AUTO TUNING SPEAKERS SPEAKERS PCM AC—3 AUTO SLEEP ROOM 2 CONTROL PTY HOLD EON NEWS INFO AFFAIRS SPORT 0 20 40 60 TUNING A/B/C/D/E...
Page 34
PREPARATION When the adjustment is finished, press the TEST key once again to cancel the test tone. Remote control TEST CLEAR ROCK CHURCH PHONO JAZZ CLUB V-AUX TEST HALL EXT. DEC. CLEAR ENTER A/B/C/D/E EFCT DISC SKIP ON/OFF PRESET CODE SET MUTE VOLUME INDEX...
Playing a source CINEMA DSP NATURAL SOUND AV RECEIVER PRESET ROOM 2 DIGITAL ENHANCED STANDBY/ON MEMORY TAPE MONITOR STEREO NORMAL WIDEPHANTOM DIGITAL AUTO TUNING SPEAKERS SPEAKERS PCM AC—3 ROOM 2 CONTROL 0 20 40 60 PTY HOLD EON NEWS INFO AFFAIRS SPORT A/B/C/D/E MEMORY MAN’L/AUTO FM...
Page 36
BASIC OPERATION NATURAL SOUND AV RECEIVER PRESET ROOM 2 DIGITAL ENHANCED STANDBY/ON MEMORY TAPE MONITOR STEREO NORMAL WIDEPHANTOM AUTO TUNING SPEAKERS SPEAKERS ROOM 2 CONTROL 0 20 40 60 A/B/C/D/E BASS TREBLE BASS TONE PHONES SPEAKERS EXTENSION BYPASS The current input mode is also shown for a source that inputs two or more types of signals to this unit.
Page 37
To select the tape deck connected to this unit’s TAPE/MD terminals or the source connected to this unit’s EXTERNAL DECODER INPUT terminals as the input source. Use one of the buttons figured below to make the corresponding indicator illuminated on the display. Front panel TAPE/MD MON /EXT.
Page 38
BASIC OPERATION Switching the input mode for the CD, DVD/LD and TV/DBS sources This unit allows you to switch the input mode for sources that send two or more types of signals to this unit. The following three input modes are provided. AUTO This mode is automatically selected when you turn on the power of this unit.
Recording a source to tape (or MD) or dubbing from tape (or MD) to tape (or MD) Recording the playing source to tape (or MD) CINEMA DSP NATURAL SOUND AV RECEIVER PRESET ROOM 2 DIGITAL ENHANCED STANDBY/ON MEMORY TAPE MONITOR STEREO NORMAL WIDEPHANTOM DIGITAL...
BASIC OPERATION Sound control Adjusting the BALANCE control Adjust the balance of the output volume to the left and right speakers to compensate for sound imbalance caused by speaker location or listening room conditions. BALANCE Note This control is effective only for the sound from the main speakers.
Tuning Basic operation Quick automatic-search tuning (automatic tuning) is effective when the station signals are strong with no interference. However, manual tuning can be used during less-than-ideal conditions. Automatic tuning Select “TUNER” as the input source. Select the reception band. “FM” or “AM” will be illuminated.
BASIC OPERATION Preset tuning Manual preset tuning This unit can store station frequencies selected by the tuning operation. With this function, you can recall any desired station only by selecting the preset station number. Up to 40 stations (8 stations x 5 groups) can be stored. CINEMA DSP NATURAL SOUND AV RECEIVER...
Automatic preset tuning You can make use of an automatic preset tuning function for FM stations. With this function, this unit performs automatic tuning and stores FM stations with strong signals sequentially. Up to 40 stations are stored automatically in the same way as in the manual preset tuning method on page 40.
BASIC OPERATION Exchanging preset stations You can exchange the places of two preset stations with each other as shown below. Example) If you want to exchange the preset stations on E1 and A5 with each other. Recall the preset station on E1 (by following the method of “To recall a preset station”...
DSP program including a combined operation of YAMAHA DSP and the Dolby Digital, Dolby Pro Logic or DTS decoder. This unit has 10 programs for digital sound field processing; 5 programs for Audio sources and 5 programs for Audio/Video sources.
Page 46
BASIC OPERATION NATURAL SOUND AV RECEIVER PRESET ROOM 2 STANDBY/ON MEMORY TAPE MONITOR STEREO AUTO TUNING SPEAKERS SPEAKERS ROOM 2 CONTROL 0 20 40 60 A/B/C/D/E BASS TREBLE BASS TONE PHONES SPEAKERS EXTENSION BYPASS Select a program that is suitable for the source. When operating on the front panel: PROGRAM Press once or more.
Page 47
To enjoy a video source encoded with Dolby Surround, Dolby Digital or DTS When you select the program No. 1, 2 or 3, and the input signal of the source is 2-channel stereo, Dolby Surround is decoded. When some program is selected and the input signal of the source is encoded with Dolby Digital, Dolby Digital is automatically decoded.
BASIC OPERATION Adjusting output level of the center, right rear, left rear speakers and subwoofer You can adjust the sound output level of the each speaker even if the output level is already set in “Speaker balance adjustment” on pages 30 to 32. Speakers CENTER RIGHT SURROUND (R SUR.)
Page 49
Method of adjustment CINEMA DSP NATURAL SOUND AV RECEIVER PRESET ROOM 2 DIGITAL ENHANCED STANDBY/ON MEMORY TAPE MONITOR STEREO NORMAL WIDEPHANTOM DIGITAL PRO LOGIC AUTO TUNING SPEAKERS SPEAKERS PCM AC—3 AUTO SLEEP ROOM 2 CONTROL PTY HOLD EON NEWS INFO AFFAIRS SPORT 0 20 40 60 TUNING...
BASIC OPERATION Brief overview of digital sound field programs The following list gives you a brief description of the sound fields produced by each of the DSP programs. Keep in mind that most of these are precise digital recreations of actual acoustic environments. The data for these sound fields were recorded at actual locations using sophisticated sound field measurement equipment.
Page 51
Program No. 2 to 3 are suitable for reproducing video discs, video tapes and similar sources which are encoded with Dolby Surround (bearing the “DOLBY SURROUND” or “DOLBY DIGITAL” logo) or encoded with DTS (bearing the “dts” logo). PROGRAM SUBPROGRAM (TYPE) MOVIE 70 mm Spectacle THEATER 1...
Page 52
BASIC OPERATION For program No. 4 and 5 only, indicators light up as follows. When the input signal is analog or PCM audio: ( When the input signal is encoded with the Dolby Digital (not in 2 channels): ( When the input signal is encoded with the DTS: ( PROGRAM MONO MOVIE TV SPORTS...
ADVANCED FEATURES “SET MENU” mode The following 13 functions maximize the performance of your system and increase the enjoyment of audio listening and video watching. 1. CENTER SPEAKER 2. REAR SPEAKER 3. MAIN SPEAKER 4. LFE/BASS OUT 5. MAIN LEVEL Changes and adjustments CINEMA DSP NATURAL SOUND...
ADVANCED FEATURES Function description 1. CENTER SPEAKER 2. REAR SPEAKER (Selecting the output modes suitable for your speaker system) Refer to pages 27 to 29 for details. (Once you have selected proper modes, you do not have to make a setting change, unless your speaker system is modified.) 6.
Page 55
8. DTS SET LFE LEVEL [Adjusting the output level at the LFE (low frequency effect) channel] Control range: –10 dB to 10 dB Preset value: 0 dB This adjustment is effective only when DTS is decoded and the signals of the selected source encoded with DTS contain LFE signals.
Page 56
ADVANCED FEATURES 11. MEMORY GUARD (Locking DSP parameters and other adjustments) If you wish to prevent accidental alteration to DSP parameters and other adjustments on this unit, select “ON”. In this position, they are locked and cannot be changed. The following functions on this unit can be locked by this operation.
This ability to create sound fields at will is exactly what Yamaha has done with the DSP.
Page 58
ADVANCED FEATURES Selecting and editing program parameters This adjustment can be made only by using the remote controller and watching the monitor screen or the display panel. Note Information on the monitor screen would be easier to see than the display panel. Set the selector dial of the remote controller to “DSP”...
Page 59
Descriptions of the digital sound field parameters Not all of the following parameters are found in every program. ROOM SIZE How it Affects the Sound: Changes the apparent size of the music venue. The larger the value, the larger the simulated room will sound. What it Does: Adjusts the timing between the early reflections.
Page 60
ADVANCED FEATURES LIVENESS How it Affects the Sound: This parameter changes the apparent reflectivity of the walls in the hall. The early reflections from a sound source will lose intensity (decay) much faster in a room with acoustically absorbent wall surfaces than in one which has mostly reflective surfaces.
Page 61
REV. LEVEL (Reverberation Level) This parameter adjusts the volume of the reverberation sound. The larger the value, the stronger the reverberation becomes. Control Range: 0 – 100% Level Direct sound REV. LEVEL S. DELAY (Surround Delay) Adjusts the delay between the direct sound and the first reflection on the rear surround side sound field.
ADVANCED FEATURES Setting the SLEEP timer Use the built-in SLEEP timer to automatically turn this unit into the standby mode after the time you set elapses. The SLEEP timer is useful when you plan to fall asleep while this unit is playing back or recording a source. The SLEEP timer also automatically turns off external units connected to the SWITCHED AC OUTLET(S) on the rear of this unit.
REMOTE CONTROLLER The remote controller is designed to control the most commonly used functions. If you have other Yamaha audio and video components with remote control capability, this remote controller will also control various functions of them. In addition, this remote controller can control other manufacturers’ audio and video components by programming the remote controller with the codes for other manufacturers.
REMOTE CONTROLLER Key name and function The key functions differ depending on the position selected by the selector dial as shown below. AMP/TUN * The keys drawn in a light tone do not function. POWER /DTS SURROUND MOVIE THEATER 1 TUNER MONO MOVIE DVD/LD...
Page 65
LEVEL This key is used to adjust the output level of the center speaker, rear speakers and subwoofer. First, press this key. Then select the speaker(s) by pressing this key repeatedly or by using the key ( ). The name will be illuminated on the display.
Page 66
For MD recorders Enter the proper code for your MD recorder. This key turns on this unit if a code for a Yamaha MD recorder is entered. If another manufactuer’s code is entered and your MD recorder’s remote controller has a power key, this key will turn on the MD recorder.
Page 67
This key turns on this unit when the default code is used. For an CD player: This key turns on this unit if a code for a Yamaha LD player is entered. (TV POWER) MENU LEFT MENU SELECT Note TV POWER, TV VOLUME and TV INPUT function if you have entered the code for your TV.
Page 68
REMOTE CONTROLLER The keys drawn in a light tone do not function. For the keys which are not described here, see “AMP/TUN” on page 62. For details, refer to the instruction manual for each of your components. Note TV POWER, TV VOLUME and TV INPUT function if you have entered the code for your TV.
Entering manufacturer codes If you have a component which is not a Yamaha model, you can enter the code for the manufacturer of the component in the corresponding position of the selector dial. By doing so, you can control the component with the remote controller.
MONO MOVIE DVD/LD ROCK PHONO HALL EXT. DEC. > < Australia model Code Position 0047 2566 CBL/DBS 3060 4545 YAMAHA DVD/LD 6187 YAMAHA 8524 YAMAHA TAPE/MD POWER STANDBY /DTS MOVIE SURROUND THEATER 2 MOVIE TAPE/MD THEATER 1 CODE SET POWER...
Refer to the chart below when this unit does not function properly. If the problem you are experiencing is not listed below or if the instruction below does not help, disconnect the power cord and contact your authorized YAMAHA dealer or service center.
Page 72
TROUBLESHOOTING Problem DSP parameters and some other settings on this unit cannot be changed. “INPUT DATA ERR” appears on the display and no sound is heard. The sound field cannot be recorded. This unit does not operate properly. A source cannot be recorded by a tape deck or VCR connected to this unit.
Page 73
Tuner Problem FM stereo reception is noisy. There is distortion and clear reception cannot be obtained even with a good FM antenna. A desired station cannot be tuned in with the automatic tuning method. Previously preset stations can no longer be tuned in. A desired station cannot be tuned in with the automatic tuning method.
AUDIO SECTION Minimum RMS Output Power Per Channel (Power Amp. Section) (When both channels are driven) MAIN L/R 20 Hz to 20 kHz, 0.04% THD, 8 ohms ... 85W+85W 1 kHz, 0.07% THD, 8 ohms ... 100W+100W CENTER 20 Hz to 20 kHz, 0.04% THD, 8 ohms ...
Page 75
Harmonic Distortion (1 kHz) Mono/Stereo ...0.1/0.2% Stereo Separation (1 kHz)...48 dB Frequency Response 20 Hz to 15 kHz ...0±1 dB Output Level (100% mod., 1 kHz) [U.S.A., Canada, China and General models] ...550 mV [Europe, U.K., Australia and Singapore models (40 kHz Dev.)] ...550 mV AM SECTION Tuning Range [U.S.A., Canada, China and General models]...
Page 76
LIST OF MANUFACTURER’S CODES LISTE DES CODES FABRICANTS For U.S.A., Canada and China models Modèles pour les Etats-Unis, le Canada et la Chine SETUP CODES FOR TV Manufacturer Code A-Mark 0003 0030, 0019, 0003, 0052, 0185 Abex 0032 Acura 0009 Admiral 0093 Adventura...
Page 88
YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN Printed in Malaysia V416020 YAMAHA MUSIC AUSTRALIA PTY, LTD.
Page 89
AMP/TUN POWER STANDBY POWER STANDBY POWER /DTS MOVIE SURROUND THEATER 2 MOVIE TAPE/MD THEATER 1 TUNER MONO MOVIE INPUT DISCO INPUT DVD/LD TV SPORTS TV/DBS ROCK CHURCH PHONO JAZZ CLUB V-AUX EXT. DEC. HALL TEST EXT. DEC. TEST CLEAR ENTER A/B/C/D/E A/B/C/D/E EFFECT ON/OFF...
Page 90
DVD MENU POWER STANDBY POWER /DTS MOVIE SURROUND THEATER 2 MOVIE TAPE/MD THEATER 1 TUNER CHANNEL MONO MOVIE DISCO Numeric DVD/LD TV SPORTS TV/DBS keys ROCK CHURCH PHONO JAZZ CLUB V-AUX TEST HALL CHANNEL EXT. DEC. CLEAR CLEAR ENTER A/B/C/D/E EFCT DISC SKIP ON/OFF...