Advertisement
APS25Z
Security with Keyless Entry
Quick Installation Guide
For Complete Installation Guide and Technical Support Please
Visit
www.voxxuniversity.com
Or Call
1-800-225-6074
2018 Voxx Electronics. All Rights Reserved.
Notifications
Alarm
When the alarm is triggered the system will provide feedback to the user.
Upon disarm, the system will beep 4x and flash the LED to indicate the Alarm
Trigger Zone.
1 Shock
2 Trunk/Hood
3 Door
Chirp Delete
System ARM/DISARM chirps can be toggled ON or OFF without entering the
Feature Bank programming.
1.
Turn the ignition key ON/OFF.
2.
Press and release the valet button 3x.
The system will respond with one (1) chirp for ON and two (2) Chirps for OFF.
This feature will not affect alarm trigger or programming.
User Programmable LED
System LED notifications can be turned ON or OFF without entering Feature
Bank programming.
1.
Turn the ignition key ON/OFF, ON/OFF.
2.
Press and hold valet button for five (5) seconds.
The LED will flash 1x for ON, 2x for OFF. This feature will not affect LED flash
during programming.
Feature Bank 2
1 Chirp
1 Lock / Unlock Function
500ms
2 Accessory Lock
OFF
3 Accessory Unlock
OFF
4 Auto Relock
OFF
5 Auto Arming
OFF
6 Parking Light/Trunk Swap
OFF
7 Silent Choice
OFF
8 Exterior Illumination
OFF
Remote Programming
The APS25Z includes two (2) programmed remotes. If required, additional
remotes can be programmed to the system. Remote Programming is located in
Feature Bank 1. To enter Remote Auto Programming:
1.
Turn the ignition key to ON.
2.
Press and release the valet button 3x. System will beep and flash the
parking lights 1x.
Press the lock button on each remote. The system will beep 1x to indicate the
remote has been programmed.
Feature Programming
The APS25Z Feature Bank can be programmed by using the valet button and
remote. To enter Feature Bank programming:
1.
Turn the ignition key to ON.
2.
Press and release the valet button 3x. System will beep and flash lights 1x
for Feature Bank 1, Remote Programming.
3.
Cycle ignition key OFF/ON. System will beep and flash lights 2x for
Feature Bank 2.
4.
Press valet button to cycle features. LED will flash to display feature
number.
5.
Press lock button to cycle options. System will beep to indicate option
number.
To exit Programming cycle ignition key OFF and wait ten (10) seconds. The
System will also automatically exit programming after sixty (60) seconds of no
activity.
Options
2 Chirp
3 Chirp
3.5sec
500ms L, Dbl UL
DBL L, 500ms UL
ON
ON
Auto Lock
Auto Lock & Arm
Auto Arm
Auto Lock & Arm
ON
From Transmitter
OEM Style
With Arm
With Disarm
With Arm & Disarm
The shock sensor should be mounted to a solid surface in the center of the
vehicle. Once mounted the shock sensor will require adjustment.
To increase sensitivity: Turn adjustment dial clockwise.
To decrease sensitivity: Turn adjustment dial counter clockwise.
To test sensitivity, strike the vehicle with an open palm. Adjust the dial to
provide coverage to as much of the vehicle as possible.
Dome Delay Programming
This system can be programmed to ignore the vehicle's theater dimming
dome light. This feature will be used when connecting the door trigger
input to the dome light circuit for alarm trigger. Note: Vehicle windows
should be open to prevent accidental locking of keys in the vehicle.
Start with all doors closed and the vehicle dome light off.
1.
Press Lock, Unlock, Lock, Unlock, Lock, Unlock, Lock. LED will light
solid.
2.
Open and close the driver door.
The system will monitor the dome light circuit. When the dome light turns
off the system will set the delay time and add an additional two (2) seconds.
Dome Delay Reset
1. Key ON/OFF, ON/OFF, ON/OFF.
2. Press and hold valet button for five (5) seconds.
The system will beep 1x to indicate reset is complete.
4 chirp
5 Chirp
6 Chirp
DBL L, DBL UL
500ms L, 350ms UL
Shock Sensor
Advertisement
