Table of Contents
Advertisement
OPERATION
Changing Flow Meter Settings
Home Screen and General Navigation
The HOME Screen displays flow volume, direction of the
flow total and flow RATE along with status conditions such
as Empty Pipe. Two buttons below the LCD display are used
to access menu screens for viewing and changing meter
setup parameters.
1.2345678
These two buttons are light sensors which can detect
T UNIT
R UNIT SET P
when a finger is covering them and activate upon
TOTAL = G ALLONS
PRESS
release. Only three button touch actions are needed to
UNIT S FOR DISPLAY
control navigation through the menus, settings changes
SET 4 SET 20 SET F
and back to the home screen.
T UNIT R UNIT SET P
HORIZONTAL SCROLLING:
T O TA L :
Tap right button to scroll horizontally through
P R E S S
menu tabs or move horizontally within a tab
SET 4 SET 20 SET F
dialog when applicable.
SELECT:
Tap left button to change a highlighted item
within a tab dialog.
ENTER/EXIT:
Hold left button while tapping right button
once to enter or exit a tab dialog or to navigate
between the HOME and other menu screens.
Changing Total Direction/Resetting Batch
Totalizers
On the Main screen, hold
to scroll through the total direction options.
Release
to select a total direction.
Once BATCH FORWARD or BATCH REVERSE is
selcted, tap
four times to reset batch totalizer.
Entering Menu System
To enter the Menu System perform the hold
and tap sequence. The Passcode entry screen
will display. The default passcode is 000000. If
a different passcode has previously been set,
use the
and
to enter that passcode.
In either case, hold and tap again to move
into the menu system. (If you enter the wrong
passcode, hold and tap again to return to the
previous screen. See page 21 for information on
how to change a passcode.)
000000
PRESS
TOTAL
CU FT
X1000
100
RATE
GPM
F O R WA R D T O TA L
DAMP
+
TO SET TOTAL
EXIT
DAMP
G A L L O N S
T O C H A N GE
EXIT
and tap
5 times
ENTER PASSCODE
AND
TO CHANGE
Making Selections
Once in the Menu System, move from tab to
tab by tapping the right button. (See the next
page for details on the various available tabs.)
Select the parameter. In the screen for
1.2345678
the highlighted tab you will see the current
parameter value for that tab. Tapping the right
button, move to the tab for the parameter you
1.2345678
want to change.
In this example, the first line indicates that the
current unit for the TOTAL is GALLONS. The
next two lines tell you what to do next.
T UNIT
TOTAL = G ALLONS
PRESS
T UNIT
UNIT S FOR DISPLAY
TOTAL = G ALLONS
SET 4 SET 20 SET F
PRESS
UNIT S FOR DISPLAY
TAP
If you would like to change the TOTAL units,
just perform the hold and tap sequence to
SET 4 SET 20 SET F
bring up a screen to change the setting.
T UNIT R UNIT SET P
TAP
T O TA L :
T UNIT R UNIT SET P
+
HOLD TAP
SET 4 SET 20 SET F
T O TA L :
SET 4 SET 20 SET F
+
Select a new setting. Select the new setting
TAP
HOLD
by scrolling through a list of selections as in
the screen illustration below by tapping the
left button to find a different TOTAL unit.
Accept changes. To accept any changes
you have made, perform the hold and tap
sequence.
+
HOLD TAP
When finished making changes. When you
are finished making changes, move to the EXIT
tab using the right button.
To return to the HOME screen, perform the
hold and tap sequence.
Page 19
FMG490 INSTRUCTIONS
TOTAL
CU FT
X1000
100
RATE
TOTAL
GPM
CU FT
X1000
100
F O R WA R D T O TA L
RATE
GPM
F O R WA R D T O TA L
R UNIT SET P
DAMP
+
TO SET TOTAL
R UNIT SET P
DAMP
EXIT
+
TO SET TOTAL
EXIT
DAMP
G A L L O N S
DAMP
P R E S S
T O C H A N GE
EXIT
G A L L O N S
P R E S S
T O C H A N GE
EXIT
TAP
TAP
+
HOLD TAP
TAP
+
HOLD TAP
TAP
+
HOLD TAP
Advertisement
Table of Contents
