Related Manuals for Pentair BIOSHIELD 522635
Summary of Contents for Pentair BIOSHIELD 522635
- Page 1 ® BI OSH I ELD UV DI S I NF E C T I ON S T E RI L I Z E R I N STALLATI ON AN D U SER’ S GU I DE I M POR TAN T SAFETY I N STRU CTI ON S READ AND FOLLOW ALL I NSTRUCTI ONS SAVE THESE I N STRUCTI ON S...
-
Page 2: Table Of Contents
CUSTOM ER SERVI CE / TECHN I CAL SUPPORT I f you have quest i ons about or der i ng Pent ai r Aquat i c Syst em s r epl acem ent par t s, and pool pr oduct s, pl ease cont act : C ust om er Ser vi ce and Techni cal Support , U SA Sanf or d, N ort h C ar ol i na ( 8 A. - Page 3 For each of the following situation, DO NOT attempt local regulations and codes. repairs yourself. Call Pentair W ater Pool and Spa, Inc. customer service department at (800) 831-7133 for services or discard the appliance. READ AND FOLLOW ALL...
-
Page 4: System Features And Specifications
SYSTEM FEATURES AND SPECIFICATIONS Bioshield Features Our low-pressure, high-output mercury vapor germicidal lamps, convert approximately 40% of their electrical input watts into UV-C output watts within the germicidal action spectrum (meaning 40% of electricity used is converted into useful germicidal UV light), the highest UV-C output conversion among all UV lamps. •... -
Page 5: Pre-Installation Inspection
PRE-INSTALLATION INSPECTION All Bioshield UV Disinfection Sterilizers are packaged complete, with all necessary components that are required to ® operate the unit. When unpacking your Bioshield UV system, we recommend that a complete component inventory be taken to ensure that all components are included and accounted for, prior to installation. Bioshield units have their serial number labels located on the UV vessel and on the power supply label. -
Page 6: Quartz Sleeve And Uv Lamp Inspection
Note (*): Power supply mounting clamps are only provided with 150W UV systems. After receipt and inspection of the unit, if broken glass is found (including cracks, chips, pin holes and hair line fractures of any kind) please contact Pentair Water Pool and Spa, Inc. at (800) 831-7133. ®... -
Page 7: Installation
INSTALLATION Quartz Sleeve Assembly and Installation Improper assembly may result in water damage to electrical components and unsafe conditions. The manufacturer is not responsible for damage cause by improper re-assembly of these parts. Quartz Sleeve Assembly Includes: Quartz Sleeve White Quartz Sleeve Retaining Nut Rubber Gasket Rubber O-ring Clear Quartz Sleeve Module... -
Page 8: Sterilizer Installation And Operation
DO NOT operate the UV system at ow rates higher than 90 GPM (341 LPM). Operating the product in this manner may result in product failure and voiding of warranty. Bioshield UV Disinfection Sterilizers are used in a variety of applications to control waterborne pathogens. Pentair ® encourages the consideration of the installation recommendations provided here. -
Page 9: Mounting The Vessel
Mounting The Vessel Note: The way UV vessels are mounted/positioned plays a very important role in the unit’s performance and degree of safety. We STRONGLY RECOMMEND that you follow these instructions and guidelines precisely. Any deviation from these mounting instructions will void any warranty associated with the UV vessel and all its components and may cause unsafe conditions. -
Page 10: Mandatory Leak Test
Mandatory Leak Test A leak test should be performed each time the quartz sleeve is installed inside the unit’s vessel or when the quartz sleeve or gaskets and o-rings are replaced [Once annually]. Performing a leak test is a precautionary measure that will determine whether or not the critical seal between the quartz sleeve and quartz sleeve module has been achieved. -
Page 11: Uv Lamp Installation
UV Lamp Installation Lamp Styles UV lamps are manufactured with color coded ceramic bases. White-capped UV lamps signify a Standard-Output UV lamp while red-capped UV lamps signify a High-Output UV lamp. Use only red-capped High-Output UV lamps with the Bioshield UV Disinfection Sterilizer. -
Page 12: Maintenance
Please note that damage to the product due to freezing is not covered under warranty. Pentair recommends shutting the UV system down when the temperature consistently falls below 40°F (4°C). 1. Drain all water from the UV system. -
Page 13: Troubleshooting
TROUBLESHOOTING Mandatory Leak Test Indicates a Leak 1. Turn off the pool pump at the circuit breaker and be sure all ow to the unit has been stopped. 2. Refer to pages 4-5 for “Quartz Sleeve Assembly” and page 8 for “UV Lamp Installation” (in reverse order) to disassemble the unit. -
Page 14: R Epl Acem Ent S Part S
REPLACEMENT PARTS Replacement Parts List Item # Description Item # Description UV Lamp Quartz Sleeve O-Ring 4-Pin Lamp Connector Quartz Sleeve Gasket Black Power Supply Jamb Nut White Quartz Sleeve Gasket/O-Ring Retaining Nut Gray Power Supply Adapter Quartz Sleeve Power Supply Cord UV Sterilizer Vessel Power Supply Module Assembly Water Inlet/Outlet Union O-Ring... - Page 15 NOTES...
- Page 16 Pentair Water Pool and Spa, Inc. Those names and brands may be the trademarks or registered trademarks of those third parties.