Yamaha MO6 Owner's Manual page 186

Song Job mode
[F3] EVENT (Event Job)
n
Before executing the Event Job, make sure that you specify the track and range (measure : beat : clock) to which the Job is applied. Please note that the track to be specified
varies depending on the Job.
01: Shift Clock
TR (Track)
001 : 1 : 000 – 999 : 4 : 479
Clock
Direction
02: Copy Event
NumberOfTimes
CAUTION
When Copy Event is executed, any data already existing at the Destination location will be overwritten.
03: Erase Event
TR (Track)
001 : 1 : 000 – 999 : 4 : 479
Event Type
04: Extract Event
TR (Track)
001 : 1 : 000 – 999 : 4 : 479
EventType
TR
05: Create Continuous Data
TR (Track)
001 : 1 : 000 – 999 : 4 : 479
EventType
Data (Data Range)
Clock
Curve
Owner's Manual
186
This Job shifts all data events in the specified range forward or backward by the specified number of clocks.
Determines the track (01 – 16, TMP, SCN, all) and range of measures/beats/clocks over which the Job is
applied.
Determines the amount by which the data will be delayed or advanced in measures, beats, and clocks.
Settings: 000:0:000 – 999:3:479
Determines the direction in which the data will be shifted. ADVANCE moves the data toward the beginning of
the sequence, while DELAY shifts the data toward the end of the sequence.
Settings: Advance, Delay
Source track and range in measures, beats, and clocks
Destination track and the top (measure, beat, and clock)
of the destination.
Determines the number of times the data is copied.
Settings: 01 – 99
This Job clears all specified events from the specified range, effectively producing a segment of silence.
Determines the track (01 – 16, TMP, SCN, all) and range of measures/beats/clocks over which the Job is
applied.
Determines the event type to be erased. All events are cleared when ALL is selected. Individual control change
numbers can be specified when erasing control change events.
Settings:
When TR is set to 01 – 16: Note (Note events), PC (Program Change), PB (Pitch Bend), CC (Control Change)*, CAT (Channel
Aftertouch), PAT (Polyphonic Aftertouch), EXC (System Exclusive), All (all events)
When TR is set to "TMP" (Tempo): TMP (tempo)
When TR is set to "SCN" (Scene): SceneMemory (Scene change information), TrackMute (Track mute setting change information)
* You can also specify the CC No. (Control Change number).
This Job moves all instances of specified event data from a specified range of a track to the same range in a
different track.
Determines the track (01 – 16) and range of measures/beats/clocks over which the Job is applied.
Selects the event type to be extracted. Specific note and control change numbers can also be specified as
required.
Settings: Note, PC (Program Change), PB (Pitch Bend), CC (Control Change), CAT (Channel Aftertouch), PAT (Polyphonic
Aftertouch), EXC (System Exclusive)
Determines the destination track (01 – 16).
This Job creates continuous pitch bend or control change data over the specified range.
Determines the track (01 – 16, TMP, all) and range of measures/beats/clocks over which the Job is applied.
Determines the event type to be created.
Settings: PB (Pitch Bend), CC (Control Change)*, CAT (Channel Aftertouch), EXC (System Exclusive), TMP (Tempo)
* You can also specify the CC No. (Control Change number).
Determines the lower and upper limits for the data range to be created. The left value is the lower limit, and the
right value is the upper limit.
Settings: When Event Type is set to PB: -8192 – +8191
When Event Type is set to TMP: 1.0 – 300.0
When Event Type is set to other: 0 – 127
Determines the number of clocks to be inserted between each created event.
Settings: 001 – 999
Determines the "curve" of the continuous data.
Refer to the graph for approximate curve shapes.
Settings: -16 – +16
This Job copies all data from a specified source
range to a specified destination location.
Execute this Job after setting:
• Source track (01 – 16, TMP, SCN, all)
• Source range (measure : beat : clock)
• Destination track (01 – 16, TMP, SCN, all)
• Destination range (measure : beat : clock)
• Top measure of destination
• Count (number of times data is to be copied)
Curve = +16 Curve = 0 (linear)
Start point
This distance specified by Clock
Curve = -16
End point