Setup Menu Map - Xantrex 120 VAC/60 Owner's Manual

SETUP MENU MAP

The SETUP MENU provides all the controls and settings needed when installing or adjusting the
system. To access the SETUP MENU, press both the red ON/OFF MENU and green GEN MENU buttons
on the Control Panel at the same time. To exit the SETUP MENU, press the red ON/OFF MENU button or
press the down MENU HEADING button until you reach the USER MENU (menu headings 1-8).
Inverter Setup
9
Set Grid Usage
FLT SELL SLT LBX
Set Low battery
cut out VDC 11.0
Set LBCO delay
minutes 10
Set Low battery
cut in VDC 13.0
Set High battery
cut out VDC 16.0
Set search
watts 48
Set search
spacing 59
Bulk Charge
Trigger Timer 15
Set Start Bulk
time 00:00
To disable timer
set to 00:00
If grid timer
active set bulk
time after start
charge time.
In SLT mode don't
disable this
timer. It is the
daily chg time.
2001 Xantrex Technology, Inc.
5916 - 195th Street N. E.
Arlington, WA 98223
MENU HEADINGS
Battery Charging AC Inputs
10
Set Bulk Set Grid (AC1)
volts DC 14.4 amps AC
Set Absorption Set Gen (AC2)
time h:m 02:00 amps AC
Set Float Set Input lower
volts DC 13.4 limit VAC
Set Equalize Set Input upper
volts DC 14.4 limit VAC
Set Equalize
time h:m 02:00
Set Max Charge
amps AC 20
Set Temp Comp
LeadAcid NiCad
Low Battery Battery Selling
Transfer (LBX) 16
Set Low Battery Set Battery Sell
TransferVDC 11.3 volts DC
Set Low battery Set Max Sell
cut in VDC 13.0 amps AC
See menu 9 to See menu 9 to
enable LBX mode. enable SELL mode.
Make sure LBX is Make sure LBX is
above LBCO volts. above LBCO volts.
Telephone: 360/435-8826
Fax: 360/435-2229
www.traceengineering.com
Gen Auto Start Gen starting
11 setup 12 details
Set Load Start Set RY7 Function
60 amp AC 20 GlowStop
Set Load Start Set Gen warmup
30 delay min 5.0 seconds
Set Load Stop Set Pre Crank
108 delay min 5.0 seconds
Set 24 hr start Set Max Cranking
132 volts DC 12.3 seconds
Set 2 hr start Set Post Crank
volts DC 11.8 seconds
Set 15 min start
volts DC 11.3
Read LBCO 30 sec
start VDC 11.0
Set Exercise
period days 30
Set Maximum run
time h:m 08:00
Set Max Run time
to 0 to defeat.
Set Exercise to 0
to defeat.
See menu 9 to
to set LBCO.
Grid Usage Timer Information file
17 18 battery
Start Charge Batt temp comp
13.4 time 21:00 changes battery
End Charge voltage reading
30 time 21:00 away from actual
After Start HBCO resets at:
Charge time: 6v/48, 3v/24 and
SELL mode 1.5v/12v under
charges battery. HBCO.
FLT mode LowBattTransfer
charges battery used in LBX, FLT
After End Charge Modes only. Goes
time: back to battery
SELL mode sells at LowBattCutIn
battery to AC1. (aka LBCI).
FLT mode drops For LBX mode set
AC1 and inverts below LBCI so
Timer on when charger won't
start < > end; cycle batteries
timer off when up and down and
start = end set LBCO below.
Sell and float
modes use timer
SLT and LBX mode
ignore timer
SW Series Inverter/Charger
Rev. C: February 2001
MENU SYSTEM
Auxiliary Relays
13 R9 R10 R11 14
Set Relay 9
Run volts DC 14.5
R9 Hysteresis
60 volts DC 01.0
Set Relay 10
10 volts DC 14.8
R10 Hysteresis
10 volts DC 01.0
Set Relay 11
30 volts DC 15.0
R11 Hysteresis
volts DC 01.0
Close on batt >
setpoint.
Open on batt <
setpoint - Hys
Relays have 2
second delay on
Close, 0.1 sec
delay on open
End Setup Menu
19 20
Page
Part No. 2031-5
35