Table of Contents
Related Manuals for Wilton A3816
Summary of Contents for Wilton A3816
-
Page 1: Cover Page
Operating Instructions — Parts Manual 15-Inch Vari-Speed Drill Press Models: A5816, A5818, A3816, A3818 Manufactured after Serial No. 807137 5507564 WMH Tool Group, Inc. 2420 Vantage Dr. Elgin, IL 60123 Ph: 847-649-3010 Fax: 847-851-1144 Part No. Revision B6... -
Page 3: Table Of Contents
Table of Contents Cover Page... 1 General Specifications ... 4 Operating Precautions ... 5 Set-up and Operation ... 7 Maintenance ... 9 Wiring Diagrams ... 10 Troubleshooting ...11 Replacement Parts ... 12... -
Page 4: General Specifications
LED speed display on the faceplate of the machine. Wilton's 15-inch vari-speed drill press provides a solid base for drilling and offers a wide range of spindle speeds. The large quill provides greater accuracy. -
Page 5: Operating Precautions
Read and follow these simple rules for best results and full benefits from your machine. Used properly, Wilton’s machinery is among the best in design and safety. However, any machine used improperly can be rendered inefficient and unsafe. It is absolutely mandatory that those who use our products be properly trained in how to use them correctly. - Page 6 General electrical cautions The drill press should be grounded in accordance with the National Electrical Code and local codes and ordinances. This work should be done by a qualified electrician. The drill press should be grounded to protect the user from electrical shock. Conductor length 0-50 feet 50-100 feet...
-
Page 7: Set-Up And Operation
Introduction This manual includes operating and maintenance instructions for the Wilton 15-Inch Vari-Speed Drill Presses, Models A5816, A5818, A5836, and A5838. This manual also includes parts listings and illustra- tions of replaceable parts. Refer to Figure 1 for key features of the drill press. - Page 8 Speed Display Speed control handwheel On/Off switch Figure 2. Operating Controls Depth Stop A drilling depth stop (refer to Figure 3) is provided on the right side of the drill head. The depth stop consists of a threaded rod with depth setting jam nuts.
-
Page 9: Cover
Difficulty of set-up. Indication of Extreme Speeds and Feeds A drill that splits up the web is evidence of too much feed or insufficient tip clearance at the center as a result of improper grinding. The rapid wearing away of the extreme outer corners of the cutting edges indicates that the speed is too high. -
Page 10: Wiring Diagrams
Adjustments Table Adjustment The table can be raised or lowered to accommodate the height of the component being drilled (refer to Figure 4). To raise or lower the table, loosen the lock handle. Then use the hand crank to move the table to the desired height. -
Page 11: Troubleshooting
Troubleshooting Problem Possible Cause Spindle does not turn. 1. Circuit breaker tripped. 2. Branch circuit breaker tripped or fuse blown. 3. Open wire in switch circuit. 4. Defective switch. 5. Broken drive belt. Spindle noisy. 1. Damaged spindle bearings. 2. Worn spline. Drill stalls. -
Page 12: Replacement Parts
Replacement Parts This section provides exploded view illustrations that show the replacement parts for the Wilton 15-Inch Vari- Speed Drill Presses, Models A58 and A38 series. Also provided are parts listings that provide part number, description, and quantity. The item numbers shown on the illustration relate to the item number on the facing page of the parts listing. - Page 13 Exploded View — Head Models: A5816, A5818, A5836, & A5838 (Note 1)
- Page 14 Parts List - Head Models A5816, A5818, A5836 and A5838 Item Part Number Description 5507580 Chuck (with Key) 5507495 #2 MT x JT3 Arbor 5507496 Spindle Assembly 5053070 Quill Band 9010541 O-Ring 9054511 Set Screw 5/16-18 x 3/8 5032611 Bearing Retainer 9100331 Bearing 5041010...
- Page 15 Exploded View — Head Models: A3816, A3818, A3836 & A3838...
- Page 16 Parts List - Head Models: A3816, A3818, A3836 & A3838 Item Part Number Description 5507580 Chuck (with Key) 5507495 #2 MT x JT3 Arbor 5507496 Spindle Assembly 5053070 Quill Band 9010541 O-Ring 9054511 Set Screw 5/16-18 x 3/8 5032611 Bearing Retainer...
- Page 17 Exploded View - Base (Floor Models A5816, A5818, A3816 & A3818)
- Page 18 Parts List - Base (Floor Models A5816, A5818, A3816 & A3818) Item Part Number Description 1000771 Locknut 5003751 Table Lock (Plain Side) 5507508 Table 5507509 Hex Head Cap Screw TS-0061091 Cap Screw 7/16-14 x 3-1/2 5041470 Collar 9129051 Hex Nut 7/16-14...
- Page 20 WMH Tool Group, Inc. 2420 Vantage Dr. Elgin, IL 60123 Ph: 847-649-3010 Fax: 847-851-1144...