Installation; Wiring And Operation - White Rodgers 24A06G-1 Installation Instructions Manual

INSTALLATION

INSTALLATION
INSTALLATION INSTALLATION INSTALLATION
The Dual-Level Temp relay may be mounted in any position
without affecting it's performance.
It can be connected using the 1/2" male conduit hub It can be connected using the 1/2" male conduit hub
It can be connected using the 1/2" male conduit hub It can be connected using the 1/2" male conduit hub It can be connected using the 1/2" male conduit hub and
can be mounted to any standard junction box or wiring
compartment.
3 25/32"
9/16"
1 3/32"

WIRING AND OPERATION

WIRING AND OPERATION WIRING AND OPERATION
WIRING AND OPERATION WIRING AND OPERATION
All wiring should be done in accordance with local and national electrical codes and ordinances.
If a wiring diagram is supplied with the heating equipment,
follow those instructions. If none is available, two diagrams are
presented which show different wiring methods for the Silent
Operator relay.
Connection Table Connection Table Connection Table
Connection Table Connection Table
2-Wire Thermostat (R & W)
Power Input:
Heat Load 1:
Heat Load 2:
OPERATION OPERATION OPERATION OPERATION OPERATION
As the thermostat closes its contacts, bimetal heaters #1 and
#2 are energized. Approximately 45 seconds later, the warp-
ing action of these heaters closes line voltage switches #1 and
#2 to energize heating loads #1 and #2.
When the thermostat opens its contacts, bimetal heaters #1
and #2 cool for approximately 45 seconds before line voltage
switches #1 and #2 open to de-energize the heating loads.
2
4 15/16"
1 3/32"
1/2" STD CONDUIT HUB
Black w/White stripe and
White to terminal W. Red to
terminal R.
Black & Blue
Red & L2
Black w/Red stripe & L2
It can also be mounted using the two holes in the back of It can also be mounted using the two holes in the back of It can also be mounted using the two holes in the back of
It can also be mounted using the two holes in the back of It can also be mounted using the two holes in the back of
the case. the case.
the case. the case. the case. Location of the mounting holes may be simplified by
holding the control against the mounting surface and marking
the proper position for drilling the holes.
2 1/8"
9/32"
3/8"
7/32"
Fig. 1. Dimensions of Type 24A06 Dual Level Temp Fig. 1. Dimensions of Type 24A06 Dual Level Temp Fig. 1. Dimensions of Type 24A06 Dual Level Temp Fig. 1. Dimensions of Type 24A06 Dual Level Temp Fig. 1. Dimensions of Type 24A06 Dual Level Temp
NOTE
Use thermostat with a .4A fixed heater,
or set adjustable heater in thermostat
at .4A.
TYPE 24A06 DUAL LEVEL TEMP
BIMETAL
HEATER #1
SWITCH #1
R
E
D
B
L
A
C
K
B
L
U
E
HEATING
LOAD #1
L1
L2
LINE
Fig. 2. Using Two-wire Heating Thermostat to Fig. 2. Using Two-wire Heating Thermostat to
Fig. 2. Using Two-wire Heating Thermostat to Fig. 2. Using Two-wire Heating Thermostat to Fig. 2. Using Two-wire Heating Thermostat to
Operate Two Separate Heating Loads Operate Two Separate Heating Loads Operate Two Separate Heating Loads Operate Two Separate Heating Loads Operate Two Separate Heating Loads
3 15/32"
2-WIRE
HEATING
THERMOSTAT
R
W
BLACK
W/WHITE
WHITE
STRIPE
RED
BIMETAL
HEATER #2
TRANSFORMER
SWITCH #2
BLACK W/RED STRIPE
RED W/BLACK STRIPE
L1
WIRING WIRING WIRING WIRING WIRING
Line Voltage
Line Voltage Field
Low Voltage
Low Voltage Field
9/16"
9/32"
3 1/16"
HEATING
LOAD #2
L2
LINE