Table of Contents
Advertisement
Quick Links
Safety • Assembly • Operation • Tips & Techniques • Maintenance • Troubleshooting • Parts Lists • Warranty
OPERATOR'S MANUAL
Model 235, S235
Single-Stage Snow Thrower
IMPORTANT
READ SAFETY RULES AND INSTRUCTIONS CAREFULLY BEFORE OPERATION
Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-covered, brush-
covered or grass-covered land unless the engine's exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any).
If a spark arrester is used, it should be maintained in effective working order by the operator. In the State of California the above is required by law
(Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands. A spark arrester
for the muffler is available through your nearest engine authorized service dealer or contact the service department, P.O. Box 361131 Cleveland,
Ohio 44136-0019.
FORM NO. 769-01801A
MTD LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019
05/2006
PRINTED IN U.S.A.
Advertisement
Table of Contents
Related Manuals for White Outdoor 235
Summary of Contents for White Outdoor 235
- Page 1 Safety • Assembly • Operation • Tips & Techniques • Maintenance • Troubleshooting • Parts Lists • Warranty OPERATOR’S MANUAL Model 235, S235 Single-Stage Snow Thrower IMPORTANT READ SAFETY RULES AND INSTRUCTIONS CAREFULLY BEFORE OPERATION Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-covered, brush- covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any).
-
Page 2: Table Of Contents
If you have difficulty assembling this product or have any questions regarding the controls, operation, or maintenance of this unit, you can seek help from the experts. To reach a local White Outdoor dealer or retailer, visit www.whiteoutdoor.com or or phone our Customer Support line at (800)-949-4483. -
Page 3: Safety Labels
Safety Labels WARNING This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury. -
Page 4: Safe Operation Practices
DANGER: This machine was built to be operated according to the rules for safe operation in this manual. As with any type of power equipment, carelessness or error on the part of the operator can Safe result in serious injury. This machine is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury or death. - Page 5 Operation 1. Do not put hands or feet near rotating parts, in the auger/impeller housing or chute assembly. Contact with the rotating parts can amputate hands and feet. 2. The auger/impeller control lever is a safety device. Never bypass its operation. Doing so makes the machine unsafe and may cause personal injury.
- Page 6 Setup And Adjustment WARNING Disconnect the spark plug wire and ground it against the engine to prevent unintended starting. NOTE: This Operator’s Manual covers several models. Snow thrower features vary by model. Not all features discussed in this manual are Chute Handle applicable to all snow thrower models.
-
Page 7: Know Your Snow Thrower
Electric Starter Button Fuel Cap Chute Assembly Shave Plate Auger Choke Lever CHOKE Activating choke control closes the choke plate on carburetor and aids in starting engine. Refer to the engine manual packed with unit for more detailed instructions. Primer Depressing primer forces fuel directly into engine’s carburetor to aid in cold-weather starting. -
Page 8: Before Starting
Operation Chute Assembly Chute Knob WARNING Read, understand, and follow all instructions and warnings on the machine and in this manual before operating. Use extreme care when handling gasoline. Gasoline is extremely flammable Your snow thrower is equipped with a two-cycle engine and the vapors are that requires a mixture of gasoline and two cycle oil at a explosive. -
Page 9: Clearing Snow
4. If your home electrical system is grounded, but a three-hole receptacle is not available, one should be installed by a licensed electrician before using the electric starter. 5. If you have a grounded three-prong receptacle, proceed as follows. 6. Move Choke Control to the “Full” position. 7. -
Page 10: Adjustments & Maintenance
Adjustments & Maintenance WARNING Disconnect the spark plug wire and ground it against the engine to prevent unintended starting. NEVER attempt to make any adjustments while the engine is running, except where specified in the operator’s manual. Before servicing, repairing, or inspecting, disengage the control bail and stop engine. - Page 11 Remove the belt cover by removing five hex screws. See Figure 6-3. Then simply pull the belt off by grasping it from the bottom of the auger pulley and pulling off. Once you remove the belt from the pulleys, you can push down on the idler pulley to release the belt from under the belt keeper.
-
Page 12: Off-Season Storage
If the snow thrower will not be used for 30 days or longer, or if it is the end of the snow season when the last possibility of snow is gone, the equipment needs to be stored properly. Follow storage instructions below to ensure top performance from the snow thrower for many more years. -
Page 13: Troubleshooting
Possible Cause(s) Solution Problem Engine fails to start 1. Fuel tank empty, or stale fuel 2. Improper fuel mixture 3. Blocked fuel line 4. Key not in ON position 5. Spark plug wire disconnected 6. Faulty spark plug 7. Engine not primed 8. - Page 14 Model S235 Determine drive pulley system by measuring this hole.
-
Page 15: Parts List
Model S235 PART No. DESCRIPTION 629-0236† Extension Cord 710-0627 Hex Screw, 5/16-24 x .75 710-1003† Screw, #10-16 x .625 7510009630 Recoil Handle 712-04063 Hex Flange Lock Nut, 5/16-18 722-3022 Foam Tape .625 X.25 726-0154 Push Mount Cable Tie 726-0205 Clamp, Hose 750-0716A Spcr., .630 x .880 x .747 736-0242... - Page 16 Model S235...
- Page 17 Model S235 PART NUMBER 684-04127 710-04071 710-0451 712-04063 720-04072 731-04388A 731-04426A 736-0119 710-04532 732-04111 725-0157 710-0805 747-04159 749-04106 684-04161 710-04187 710-1003 710-1882 712-0252 725-2018 736-0225 736-0400 750-0589 736-0362 710-0134 710-3008 712-04064 731-1033 736-0176 746-04237 749-04114 725-0201 731-1133C 731-04127 731-04353 731-04886 DESCRIPTION Chute Assembly Carriage Bolt 5/16-18 x 1.0”...
-
Page 18: Notes
NOTES:... - Page 19 NOTES:...
-
Page 20: Warranty
MANUFACTURER’S LIMITED WARRANTY FOR The limited warranty set forth below is given by MTD LLC with respect to new merchandise purchased and used in the United States, its posses- sions and territories. “MTD” warrants this product against defects in material and workmanship for a period of two (2) years commencing on the date of original purchase and will, at its option, repair or replace, free of charge, any part found to be defective in materials or workmanship.