Diamond Audio dealer to achieve the best possible system recommendation and installation. This will ensure a true Diamond Audio listening experience and sound you would expect from Diamond Audio products. With proper validation, using a Diamond Audio Retialer for installation,...
INSTALLATION -Pre Planning Section WARNING: Prolonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. DIAMOND AUDIO amplifiers can exceed that level so please exercise restraint when listening to your new amplifier. GENERAL PRECAUTIONS • This unit is designed for negative ground 12V DC operation only.
Page 6
Original equipment electrical systems, which are in good condition, should be able to handle the extra load of any DIAMOND AUDIO amplifier without problems, although battery and alternator life can be reduced depending on your individual listening habits.
Page 7
INSTALLATION 5. Prepare the ground wire for attachment to the amplifier by stripping 5/8" of insulation from the end of the wire. Always use a wire of the same gauge as the power connection, never smaller. Insert the bare wire into the GND terminal and tighten the set screw to secure the cable in place.
Page 8
SET UP Placing the x-over switch in the FULL position (MICRO4V2/MICRO5V2) sets the amplifier to Full Range. This setting allows ALL frequencies to pass to the speakers. With the MICRO4V2/MICRO5V2, Placing the switch in the HP or LP position activates the 12dB crossover, adjustable from 40Hz - 400Hz.
5. BTR Port – (Bluetooth Receiver Port) This port is specifically to be used with any DIAMOND AUDIO Bluetooth controller. This will allow direct plug in to the amplifier and control simple functions of music playback through the BTR receiver. The supplied cable is the ONLY cable that can be used to plug into the BTR port on the amplifier.
Page 10
SYSTEM CONFIGURATIONS MICRO4V2- 4 CHANNEL CONFIGURATION STEREO FRONT/REAR SETUP MICRO4V2 SIGNAL ENDPLATE FRONT INPUT REAR INPUT SIGNAL HARNESS SIGNAL HARNESS PREAMP OUT FRONT PREAMP OUT REAR HEAD UNIT (PREFERABLY WITH 5V OUTPUT) MICRO4V2 POWER/SPEAKER ENDPLATE BATTERY FRONT OUTPUT SPEAKER HARNESS REAR OUTPUT SPEAKER HARNESS STEREO FULL-RANGE...
Page 11
SYSTEM CONFIGURATIONS MICRO4V2 - FULL MARINE/HOT ROD SYSTEM WITH BTR SMARTPHONE (BLUETOOTH) DABTR (BLUETOOTH RECEIVER) SPECIAL BTR CABLE (INCLUDED WITH BTR) MICRO4V2 SIGNAL ENDPLATE MICRO4V2 POWER/SPEAKER ENDPLATE BATTERY FRONT OUTPUT SPEAKER HARNESS REAR OUTPUT SPEAKER HARNESS 8 - 8 INCH HXM8 EXTREME HIGH OUTPUT 2-WAY SPEAKER FRONT...
Page 12
SYSTEM CONFIGURATIONS SPEAKER LEVEL INPUT (OPTIONAL): MICRO1V2 - Monoblock Subwoofer(s) MICRO1V2 SIGNAL ENDPLATE INPUT SIGNAL HARNESS SUB PRE OUTPUT FROM HEADUNIT HEAD UNIT (PREFERABLY WITH 5V OUTPUT) MICRO2V2 - Stereo 2 ohms MICRO1V2 POWER/SPEAKER ENDPLATE w/4 speakers BATTERY SPEAKER OUTPUT HARNESS MICRO2V2 SIGNAL ENDPLATE INPUT SIGNAL...
Page 13
SYSTEM CONFIGURATIONS MICRO5V2 - 5 CHANNEL SYSTEM MICRO5V2 SIGNAL ENDPLATE FRONT INPUT SIGNAL HARNESS REAR INPUT SIGNAL HARNESS HEAD UNIT (PREFERABLY WITH 5V OUTPUT) MICRO5V2 POWER/SPEAKER ENDPLATE FRONT AND REAR CO-AXIALS/COMPONENTS (4 Ohms OR 2 Ohms) SUBWOOFER(s) (4 Ohms OR 2 Ohms)
SPECIFICATIONS PRODUCT SPECIFICATIONS MICRO1V2 MICRO2V2 MICRO4V2 MICRO5V2 950 W RMS 150 W X 4/350 W X 1 300 W 80 W X 4/200 W X 1 175 W 500 W 300 W 300 W X 2/200 W X 1 175 W 200mV - 10.0V 200mV - 10.0V 200mV - 10.0V...
LIMITED WARRANTY STATEMENT Diamond Audio Technologies (DAT), a division of CV & DA Holdings Incorporated, warrants this product to be free from defects in material and workmanship for a period of one (1) year from the original date of purchase, provided it was purchased from an authorized DAT retailer within the United States.