Carrier WeatherExpert 48LC 07 Series Installation Instructions Manual page 33

Table 9 — Economizer Module
(Left Hand Terminal Blocks)
LABEL TYPE
Top Left Terminal Block
MAT
20k NTC Mixed Air Temperature Sensor (Polarity
MAT
and COM Insensitive Connection)
OAT
20k NTC Outdoor Air Temperature Sensor (Polarity
OAT
and COM Insensitive Connection)
S-BUS
S-BUS Enthalpy Control Sensor
S-BUS
(Sylk* Bus) (Polarity Insensitive Connection)
Bottom Left Terminal Block
Air Quality Sensor Input (e.g. CO
IAQ 2-10
2-10 vdc
sensor)
IAQ COM
COM Air Quality Sensor Common
IAQ 24V
24 vac Air Quality Sensor 24 vac Source
ACT 2-10
2-10 vdc Damper Actuator Output (2-10 vdc)
ACT COM
COM Damper Actuator Output Common
ACT 24v
24 vac Damper Actuator 24 vac Source
*Sylk is a trademark of Honeywell International Inc.
Table 10 — Economizer Module
(Right Hand Terminal Blocks)
LABEL TYPE
Top Right Terminal Blocks
AUX2 I
24 vac IN The first terminal is not used.
Shut Down (SD) or HEAT (W)
Conventional only
OCC
24 vac IN and
Heat Pump Changeover (O-B) in Heat
Pump mode.
E-GND
E-GND Occupied/Unoccupied Input
EXH1
24 vac OUT Exhaust Fan 1 Output
Programmable:
Exhaust fan 2 output
or
AUX1 O
24 vac OUT
ERV
or
System alarm output
Bottom Right Terminal Blocks
Y2 in - Cooling Stage 2 Input from space
Y2-I
24 vac IN
thermostat
Y2 out - Cooling Stage 2 Output to stage
Y2-O
24 vac OUT
2 mechanical cooling
Y1 in - Cooling Stage 2 Input from space
Y1-I
24 vac IN
thermostat
Y1 out - Cooling Stage 2 Output to stage
Y1-O
24 vac OUT
2 mechanical cooling
C
COM 24 vac Common
R
24 vac 24 vac Power (hot)
S-Bus Sensor Wiring
The labels on the sensors and controller are color coded for
ease of installation. Orange labeled sensors can only be wired
to orange terminals on the controller. Brown labeled sensors
can only be wired to S-bus (brown) terminals. Use Fig. 52 and
Table 11 to locate the wiring terminals for each S-Bus and en-
thalpy control sensor.
DESCRIPTION
2
DESCRIPTION
S-BUS
TERMINALS
(1 AND 2)
Fig. 52 — S-Bus Sensor DIP Switches
Table 11 — HH57AC081 Sensor Wiring Terminations
TERMINAL
NUMBER LABEL
1
S-BUS
2
S-BUS
Use Fig. 52 and Table 12 to set the DIP switches for the desired
use of the sensor.
Table 12 — HH57AC081 Sensor DIP Switch
DIP SWITCH POSITIONS FOR SWITCHES 1, 2, AND 3
USE
1
DA
OFF
RA
ON
OA
OFF
NOTE: When an S-Bus sensor is connected to an existing net-
work, it will take 60 minutes for the network to recognize and
auto-configure itself to use the new sensor.
During the 60-minute setup period, no alarms for sensor fail-
ures (except SAT) will be issued and no economizing function
will be available.
CO Sensor Wiring
2
When using a CO sensor, the black and brown common wires
2
are internally connected and only one is connected to "IAQ
COM" on the W7220. Use the power from the W7220 to pow-
er the CO sensor OR make sure the ground for the power sup-
2
plies are common. See Fig. 53 for CO
33
DIP
SWITCH
LABEL
DIP
SWITCHES
(3)
S-BUS
2 PIN SIDE
CONNECTOR
TYPE DESCRIPTION
S-BUS
Communications
S-BUS
(Enthalpy Control
Sensor Bus)
S-BUS
Communications
S-BUS
(Enthalpy Control
Sensor Bus)
2 3
ON OFF
OFF OFF
OFF OFF
sensor wiring.
2