Timed Cooking; Sequence Programming - Whirlpool 8522773A Use And Care Manual

Timed Cooking

WARNING
Food Poisoning Hazard
Do not let food sit in oven more than one hour
before or after cooking.
Doing so can result in food poisoning or
sickness.
Timed Cooking allows the oven to be set to turn on at a certain
time of day, cook for a set length of time, and/or shut off
automatically. Delay start should not be used for food such as
breads and cakes because they may not bake properly.
To Set a Timed Cook:
1. Press BAKE (optional).
Press the TEMP "up" or "down" arrow pads to enter a
temperature other than the one displayed.
2. Press STOP TIME.
3. Press the HR and MIN "up" or "down" arrow pads to enter
the desired time to end cooking.
4. Press START.
The display will count down the time.
When the time ends, the oven will shut off automatically and
"End" will appear on the display.
End-of-cycle tones will sound, then, if enabled, reminder
tones will sound every minute.
5. Press OFF or open the oven door to clear the display and/or
stop reminder tones.
To Set a Delayed Timed Cook:
Before setting, make sure the clock is set to the correct time of
day. See "Clock" section.
1. Press desired cook function.
Press the TEMP "up" or "down" arrow pads to enter a
temperature other than the one displayed.
2. Press START TIME.
3. Press the HR and MIN "up" or "down" arrow pads to enter
the time of day to start.
4. Press STOP TIME (optional).
5. If STOP TIME has been pressed, press the HR and MIN "up"
or "down" arrow pads to enter the desired time to end
cooking.
6. Press START.
"DELAY" will appear on the display.
When the start time is reached, the oven will automatically
turn on.
When the stop time is reached (if programmed), the oven will
shut off automatically and "End" will appear on the display.
End-of-cycle tones will sound, then, if on, reminder tones will
sound every minute.
7. Press OFF or open the oven door to clear the display and/or
stop reminder tones.
16

Sequence Programming

(on some models)
Sequence Programming allows you to program at one time up to
four cook functions, and can be used at the same time with other
oven functions, such as the Timer and Warming Drawer.
Sequence Programming takes precedence over any non-
sequenced cook function. For example, if an un-timed Bake
function is in process and a sequence program is started, the
un-timed Bake function will be canceled, and the program
sequence will start.
All steps of a sequenced program, except for the last step, must
be programmed with a stop time. If a stop time is not entered for
a step in the sequence program, and the FIRST/NEXT STEP pad
is pressed, three tones will sound.
To Program the First Step of the Sequence:
1. Press FIRST/NEXT STEP .
"PROGRAM" and "STEP" will appear on the display. A
flashing "1" will also appear on the display, indicating that
step 1 is being programmed.
2. Choose the desired cook function by pressing any cook
function key.
Press TEMP "up" or "down" arrow pad (if desired) to select
temperature.
3. Press START TIME, then HR and MIN "up" or "down" arrow
pads to set the time of day for the first cook function to begin.
If START TIME is not pressed, then the sequence of cook
functions will begin immediately once programming is
complete and START is pressed.
The display will show either the time of day (if start time was
not programmed) or the start time (if same was programmed),
but with a flashing colon. "Stop" and "Time" will also appear
on the display.
4. Press STOP TIME, then HR and MIN "up" or "down" arrow
pads to set the time of day for the first cook function to stop.
To Program Next Steps of the Sequence:
1. Press FIRST/NEXT STEP .
"PROGRAM" and "STEP" will appear on the display. The
number of the steps being programmed will flash.
"START" and "TIME will appear on the display.
2. Choose the desired cook function by pressing any cook
function key.
Press TEMP "up" or "down" arrow pad (if desired) to select
temperature.
3. Press STOP TIME, then HR and MIN "up" or "down" arrow
pads to select stop time.
4. Press START to begin sequence.
5. Press OFF/CANCEL at any time to clear program and to stop
program.
To Review/Modify Programmed Sequence:
If program steps are partially or completely programmed, yet the
sequence has not been started, the programmed cook functions
can be reviewed.
1. Press REVIEW STEPS. Step 1 will appear in the display
Subsequent presses of REVIEW STEPS will cause display of
programmed steps in order.
"STEP" and "RECALL" will appear on the display. The
number of the displayed step will flash. A recalled step will
remain lit on the display for 5 minutes if no further action is
taken.