DeLonghi HSX4315ECA Instructions For Use Manual page 13

Use on the floor
Turn the radiator upside-down on a rug or a soft surface in
order to prevent damaging the paint finish. Rotate the feet
as shown in figure 2 in order to put the feet in position.
Turn the radiator back to its upright position.
See Figure 3 for the minimum distances of the appliance
from the walls.
Important! Use this heater on a flat hard floor.
Important! never use the appliance without feet if it is
not mounted on the wall.
Important! when using the appliance position the
feet as shown in figure 2 only.
Installation on the wall
The kit for wall installation contains:
2 metal brackets for mounting upper support (J)
2 metal brackets for mounting lower support (K)
2 butterfly screws M5 (L)
4 screws 4.5 x 25 PH (M)
4 plastic wall anchors 6 x 30 (N)
Tools required for wall mount installation
Drill
Screwdriver PH 2x100 (phillips head)
Estimated time for installation: 30 minutes
Before installing the unit, ensure the following:
a. The device must not be placed directly under a
power socket.
b. The plug and power socket must be easy to reach
after installation.
c. No electric cables or other pipework could be
damaged during installation.
d. Keep away from curtains or flammable materials.
Do not install the appliance on flammable walls.
For wall mounting, proceed as follows:
Turn the appliance upside down on a flat and stable surface.
Press the "PUSH" button on the bottom of the foot to allow
it to rotate to its original position as shown in figure 4 and
expose the screw.
Remove the screw as shown in figure 5 to unhook the feet from
the appliance as shown in figure 6. Fix the two brackets K with
the two butterfly screws L as shown in Fig. 8.
1. Before drilling the wall, mark the exact spot, respecting
the minimum distances as shown in Fig. 7.
2. Drill following the marks that you have made and insert
the wall plugs N. For brick walls use a masonry bit
of 6 mm. For plasterboard or false walls (empty), we
recommend the use of appropriate screws and anchors
(not supplied).
3. Fix the 2 metal brackets J to the wall using the screws M
provided.
4. Hang the appliance on the brackets.
5. Mark the lower fixing points corresponding to the holes
of the brackets K. Remove the appliance, drill the lower
holes and insert the wall plugs N .
6. Now you can hang the unit on the brackets and secure the
bottom of the appliance with the 2 screws M remaining.
USE
Operation and use
- Plug into the outlet socket.
- The appliance emits a beep. The power indicator light
(A) comes on and remains lit while the appliance is
powered.
- The appliance switches to standby.
- Press the ON/OFF (B) to turn the appliance on. It begins
heating the room according to the current settings.
- Press the MODE (D) button to select one of the following
operating modes:
Freeze prevention
-
In this mode, the appliance keeps the room at a
temperature of 7°C (45°F) to avoid freezing.
Heating 1, 2, 3 and Heating 3 + Fan
-
In this mode, the desired temperature can be selected by
pressing the adjustment buttons + and –. By pushing
the + or - button once, the temperature (shown on the
display) will increase or decrease by 1 degree.
Heating 1
The appliance operates at low power.
Heating 2
The appliance operates at medium power.
Heating 3
The appliance operates at high power.
Heating 3 + Fan
The appliance operates at the maximum power with
the fan. The setting temperature range available is from
16°C to 32°C (61°F to 90°F).
"ECO plus" function
The "ECO plus" function is available in Heating 1, 2 3 and 3
+ fan modes only. To activate the function, press the "ECO
plus" (E) button.
When this function is active the appliance automatically sets
the most appropriate power level to guarantee optimum
13