Sylvania SP332-ASST3-PL Quick Start Manual

Water Resistant & Rugged Wirless Speaker
SP332-ASST3-PL
Introduction
SP332-ASST3-PL
Y
and enjoy handsfree calling.In order to get the best results
when using the device,please read this manual first before using.
Important Waterproof/Safety Information
Important: DO NOT submerge the SP332-ASST3-PL speaker in
water,this unit is not intended to function properly after being
under water.
SP332-ASST3-PL is rated IPX6,which means the speaker can be
heavily splashed with water or left in the rain(but not submerged in
water) for approximately a limited time.If the SP332-ASST3-PL
gets wet,it is recommended that you dry the speaker completely
before using it again.
Please note:Speaker is not water-resistant when the silicone cover
is open.please make sure that cover is closed and secure before
using in a wet environment.
Description:
4 678 5
1 2 3
9 10
1.ON/OFF button
2.Play/Pause/Phone
3.MIC
4.Previous/Volume –
5.Next/Volume +
6.Blue LED(Bluetooth)
7.Red LED(Charging)
8.Green LED(AUX)
9.Micro USB Charging Port
10.AUX in Port
Included:
1.Speaker
2.USB Micro Charging Cable
3.3.5 mm Audio Cable
4.User Manual
Specifications
Bluetooth Version : 2.1+EDR
Supported Profiles: A2DP, HFP, AVRCP
Bluetooth Range:33ft (10m)
Dimensions: 180 mm x 65 mm
Battery: rechargeable Lithium-ion battery
Charging: 5V @ 500 mA
Operation
Powering On
Press and Hold "ON/OFF" button 2 seconds to power ON, the
Blue LED will start to flash.
If an Aux (3.5 mm) cable is connected to the unit, the Blue LED
will turn off, and the Green LED will stay illuminated,notifying you,
the uint is in Aux-In mode.
Powering Off
Press and Hold "ON/OFF" button 2 seconds to power OFF
Bluetooth Mode
Pairing
The unit will automatically go into "Pairing Mode" when it is
powered ON.
Go into your Bluetooth device settings menu and look for
"Sylvania SP332"
After the unit has paired and connected, it will re-connect
automatically when the unit is powered on and the device
is in range.
Note: Bluetooth Timeout :10 minutes
Begin Streaming Music
Press " " to start playing music
Press and Hold"
Press and Hold"
Press either "
Making and Receiving Phone Calls
When the unit is connected and paired to your device,
the unit allows you to make or receive phone calls with its
built-in microphone.
Press " " to accept a call
To end a call press"
To reject a call, press and hold "
Aux-In Mode
Plug in the supplied 3.5 mm cable into the unit. The other end is
connected to your device. The Green LED will only illuminate
when in "Aux" mode.
Please note music and volume can be controlled by your device.
Charging
Attach the USB cable to the unit, and plug into any USB charger.
If the unit is completely discharged, it will take approximately 4
hours to fully charge.
The Red LED will illuminate during charging, when it has
completed, the Red LED will turn off.
Note:There will be a beep when the battery is low and needs to
be recharged.
LED Status
Blue LED flashing & Blue LED solid
Green LED on solid
Red LED
.
Troubleshooting
Unit doesn't connect
to device
A tone is heard every few seconds
Unit will not power on
Unit doesn't control
track(s)/volume
Unit distorts at
high volume
For service assistance and product information, please call: 1-800-968-9853.
Pour obtenir assistance et information appelez: 1-800-968-9853.
Curtis International Ltd.
7045 BECKETT DRIVE, UNIT 15, MISSISSAUGA, ON, L5S 2A3
www.curtisint.com
" 2 seconds to play the next track
" 2 seconds to play previous track
" or " " for volume control
"
" for 2 seconds
Bluetooth Mode
Aux Mode
Charging
Speaker needs to be connected/
re-paired to device
Speaker needs to be charged
Speaker needs to be charged
Speaker needs to be in Bluetooth
mode for full control
The devices' volume needs to
be lowered