Page 1
ACER AL708 Lcd WARNING SAFETY PRECAUTIONS DIMENSIONS GENERAL INFORMATION SPECIFICATIONS THEORY OF OPERATION DISASSEMBLY INSTRUCTIONS CONTROL LOCATION NECESSARY EQUIPMENT LIST BLOCK DIAGRAM CONDUCTOR VIEW SCHEMATIC DIAGRAM TROUBLE SHOOTING HINTS REPLACEMENT PARTS LIST SPARE PARTS LIST...
Page 2
SAFETY PRECAUTIONS 1. CAUTION: 4-6 Voltage measured must not exceed 1.5 volt No modification of any circuit should be attempted. RMS, from any exposed metallic part to the Service work should only be performed after you ground. A leakage current tester may be are throughly familiar with all of the following safety used in the above hot check, in which case checks and servicing guide lines.
Page 3
1. DIMENSIONS~1 unit : mm Front Side Rear Side...
Page 4
1. DIMENSIONS~2 unit : mm Base Unit Side View...
Page 5
2. GENERAL INFORMATION 1. OUTLINE 2.8 Superior display performance This monitor is 17" multi-scan color LCD display High contrast : 350 : 1 with the following features. High brightness : 250 cd / m (Typical) OSD ( on screen display ) control allows easy user Wide view angle : 140 / 100 degrees (H/V) adjustment.
Page 6
3. SPECIFICATION 1. Outline 4.2 Audio : Line-in receptacle 1.1 POWER SW, LED,UP.DN,LEFT,RIGHT,SEL and MENU key are located on the front panel. 1.2 Video signal connector, audio line-in receptacle and DC-IN are located on the back side of the cabinet. 1.3 OSD menu includes the following function.
Page 7
5. ELECTRICAL SPECIFICATIONS 5.4 Preset Timings 5.1 Standard conditions Display area 338 x 270 mm mode Resolution (KHz) Video signal level 0.7 Vpp IBM VGA 720 x 400 31.46 Contrast Max. VESA 640 x 480 31.46 Brightness Max. MAC 13” 640 x 480 Ambient 20 +/- 5 C degrees...
Page 8
5.6 Display Area 6. ENVIRONMENTS Display area : 338 x 270 mm Operation Storage and Shipment 5.7 General performance 5.7.1 Maximum pixel clock Tempera 0 ~ 40 C -20 ~ +60 C 135 MHz ture 5.7.2 Maximum luminance Humidit 5 ~ 90 % 5 ~ 90 % * Altitude 3000m...
Page 9
4. THEORY OF OPERATION This section describes the function of the LCD monitor per functional block. L7EA monitor includes MB board, audio board (option), inverter board, adapter and button board. 4.1 MB BOARD The MB board is a four-layer, single-landed design with ground and internal planes provided. DC power from the power adapter enter the board through DC jack.
Page 11
4.1.3 Power Regulator AIC1563 (U12),LT1117 (U5, U6) The AIC1563 is a monolithic control IC containing the primary functions required for DC to DC converters. The device consists of an internal temperature compensated reference, conparator, controlled duty cycle oscillator with an active current sense circuit. Desired output voltage are determined by the equation Vout = 1.25 ( 1 + R104 / R103), In this case, the output voltage are 5 Volts.
Page 12
4.4 Adapter This is a general purpose AC / DC adapter which converter 90~240 Vac to a stabilized DC voltage 12 V with rated output current of 4.16A . Electrical specification describled as below. INPUT Rated Input Voltage 90~240 Vac , 50/60 Hz Operation Input Voltage 90~260 Vac, 47~63 Hz Input Current...
Page 13
5. DISASSEMBLY INSTRUCTIONS 1. Stand& rear cover removal 1) remove four large screw "1" from the rear cover 2) remove the rear cover 3) remove four screw "2" 4) remove the stand 2. ESD cover removal 1) remove four screw "3" 2) remove the ESD cover 3.
Page 14
4. Inverter board removal 1) remove two screw "5" 2) remove the Inverter board 6. Panel module removal 1) remove four screw "6" 2) remove the Panel module 7. Panel removal 1) remove four screw "7" 2) remove the Panel...
Page 15
6. CONTROL LOCATION MENU Power ← ↑ → ↓ Selected or change function To power on and To increase level off the display of selected item power status To decrease level indicator ( LED ) of selected 1)To step up the parameter 2) volume 1)To step down...
Page 16
Vertical position. Press the △ and ▽ buttons to move image up and down. Horizontal position. Press the <l and l> button to move image left and right. The Auto function configures the vertical and horizontal position for you. Language. Press the <l and l> buttons to change the OSD language display setting.
Page 17
7. NECESSARY EQUIPMENT LIST Item Personal Computer with Windows 98 or above version Luminance Meter Minolta CA 110 Video Gnerator : Chroma 2000,2135,2250 or equivalent Colour Analyzer : Minolta , Chroma or equivalent Watt / Power Meter 10 Times Magnifier...