TABLE OF CONTENTS TABLE OF CONTENTS ... i DIGITAL TELEVISION TRANSITION NOTICE ... 1 AVISO RELATIVO A LA TRANSICIÓN A TELEVISIÓN DIG- ITAL ... 1 IMPORTANT INFORMATION ... 2 Warnings ... 2 NOTICES ... 3 FCC COMPLIANCE STATEMENT ... 4 IMPORTANT SAFETY INSTRUCTIONS ...
TABLE OF CONTENTS EXTERNAL DEVICE CONNECTIONS ... 18 POWER CONNECTION ... 20 CONNECTING AC POWER ... 20 INITIAL SETUP ... 20 BASIC OPERATIONS ... 21 TURNING THE POWER ON AND OFF ... 21 ADJUSTING THE VOLUME ... 21 CHANGING CHANNELS ... 22 SELECTING THE INPUT SOURCE ...
DIGITAL TELEVISION TRANSITION NOTICE DIGITAL TELEVISION TRANSITION NOTICE This device contains a digital television tuner, so it should receive digital over the air TV programming, with a suitable antenna, after the end of full-power analog TV broadcasting in the United States on June 12, 2009. The nationwide switch to digital television broadcasting will be complete on June 12, 2009, but your local television stations may switch sooner.
IMPORTANT INFORMATION IMPORTANT INFORMATION To reduce the risk of fire or electric shock: • Do not expose this product to rain or moisture. • Do not remove the rear cover. There are no user-serviceable parts inside. Refer all servicing requirements to qualified service personnel. •...
CAUTION: The power supply outlet should be located near the LCD TV and should be easily accessible. Always use the appropriate AC cord that is certified for your specific country. Some examples are listed below: • USA – UL • Canada –...
• if the interference persists even after performing the above measures, consult the Westinghouse Service Center or an experienced radio/TV technician for assistance. FCC Warning To assure continued FCC compliance, use a grounded power supply cord and the provided shielded video interface cable with bonded ferrite cores.
IMPORTANT SAFETY INSTRUCTIONS Make sure to note and follow all warnings and instructions marked on the LCD TV. Observe the following safety instructions. • Read these instructions. • Keep these instructions. • Heed all warnings. • Follow all instructions. • Do not use this apparatus near water.
IMPORTANT INFORMATION Circuit Overload Do not overload wall outlets, extension cords, or power strips. This can result in a fire or electronic shock. Power Cord Protection Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them.
Do not place heavy objects on the LCD TV, audio/video cables, or power cord. • If the LCD TV emits smoke, abnormal noise, or a strange odor, immediately turn it off and contact the Westinghouse Service Center by: – Logging on to www.wde.com. –...
IMPORTANT INFORMATION ANTENNA INSTALLATION SAFETY Outdoor Antenna Grounding If an outside antenna or cable system is connected to the LCD TV, be sure the antenna or cable system is grounded to prevent voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANS/NFPA 70, provides information on proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.
CLEANING THE LCD TV • Make sure the LCD TV is turned off and the power cord is disconnected from the power outlet. • Never spray or pour any liquid directly onto the screen or the case. To clean the screen: 1 Wipe the screen with a clean, soft, lint-free cloth.
PACKAGE CONTENTS PACKAGE CONTENTS 32” LCD TV Unit LCD TV Base Power Cord User Manual Product Brochure Remote Control (with 2x AAA batteries) C.C. Favorite Enter Input YPbPr1 HDMI1 Video1 YPbPr2 HDMI2 Video2 RMT-11 Quick Connect Guide Warranty Card Warranty Brochure M4 x L10 mm Screw for Base...
CONTROL PANEL Item 1. Menu 2. Volume +/- 3. Channel +/- 4. Source 5. Power Menu Volume Channel Source Power Description Display the LCD TV setup screen. During playback, adjust the volume; in a menu screen, select an item. During TV viewing, adjust the channel; in a menu screen, select an item.
REMOTE CONTROL Z Z Z C.C. Favorite Enter Input YPbPr1 HDMI1 Video1 YPbPr2 HDMI2 Video2 RMT-11 Item Description Mute the sound. Press it again to 1. Mute toggle the sound back on. Toggle the TV power on and off. 2. Power Adjust the LCD screen backlight.
REMOTE CONTROL OPERATION REMOTE CONTROL OPERATION INSTALLING THE REMOTE CONTROL BATTERIES CAUTIONS: • Only use AAA batteries. • Do not mix new and old batteries. This may result in cracking or leakage, which may pose a fire risk or lead to personal injury. •...
LCD TV BASE CAUTION: The LCD TV unit may be too heavy for one person to lift. If this is the case, make sure to ask for assistance in handling the LCD TV to prevent physical injury and/or damage to the unit. INSTALLING THE LCD TV BASE 1 Open the LCD TV carton box.
LCD TV BASE REMOVING THE LCD TV BASE If you intend to repack the LCD TV unit (for shipping or storage) or you want to change the installation to a wall mount option, you must first remove the LCD TV base.
ANTENNA CONNECTION OUTDOOR ANTENNA CONNECTION Cable TV lead in VHF, UHF or VHF/UHF combination antenna 75 ohm coaxial cable (round) 300 ohm twin-lead (flat) Separate VHF/UHF Antenna VHF Antenna UHF Antenna 300 ohm twin-lead 300 ohm twin-lead 75 ohm coaxial cable CABLE TV (CTV/DTV) CONNECTION The unit has a TV tuner (75 ohm coaxial cable connector) located on the rear I/O panel for easy cable hookup.
EXTERNAL DEVICE CONNECTIONS • A position on the RF switch (not supplied) – You can view all unscrambled channels by using the TV's channel keys. • B position on the RF switch (not supplied) – You can view the scrambled channels via the converter/descrambler by using the converter's channel keys.
Page 23
The following diagram shows the external device connections. HDMI HDMI DVI-HDMI conversion cable Audio amplifier HDMI DVD Player DVD Player Audio output terminal (with DVI terminal) (with HDMI terminal) AUDIO OUT Audio Audio cable HDMI PC AUDIO PC / VGA 3.5 mm stereo mini jack cable...
POWER CONNECTION POWER CONNECTION CONNECTING AC POWER IMPORTANT: The LCD TV works on a 120 VAC, 60 Hz power input voltage ONLY. Turn off all connected devices before plugging in the power cord. Connect the power cord to the LCD TV then to a proper AC outlet. INITIAL SETUP Press on the control panel or on the remote control to turn on the LCD TV.
BASIC OPERATIONS TURNING THE POWER ON AND OFF Turning on the power Press on the control panel or on the remote control to turn on the LCD TV. Turning off the power Press on the control panel or on the remote control to turn off the LCD TV. The LED behavior will depend on the enabled Power settings.
BASIC OPERATIONS CHANGING CHANNELS Referred to in the following instructions to change channels. Using the Ch Buttons Browse channels Input To browse through the available channels, press Ch YPbPr1 HDMI1 Video1 the remote control or on the control panel. YPbP 2 HDMI2 Using the Channel Keys Favorite...
Using the Input Key Select source using Input Key Input 1 Press Input. YPbPr1 HDMI1 Video1 2 A list of supported video sources is displayed. 3 Press 4 Press ADJUSTING THE DISPLAY FORMAT The input source can sometimes affect the way images are displayed on-screen. You can adjust the display format to view the image properly.
SETUP MENUS SETUP MENUS SETUP MENU OPERATION Use the setup menus to configure the various operational settings of the LCD TV. Displaying the setup menu screen Press on the remote control or Menu on the control panel to display the setup menu screen.
PICTURE Use the Picture sub-menus to configure the display quality. Press on the remote control or Menu on the control panel to display the setup menu screen then select Picture to display the Picture sub-menu. The following options are available: Brightness, Contrast, Saturation, Video Presets, Sharpness, Color temperature, Hue, and Reset.
Page 30
SETUP MENUS Saturation Use Saturation to adjust the color intensity. Adjusting Saturation 1 Use the keys to select Saturation and press 2 Press the keys on the remote control to adjust the option level. 3 Press to save and exit the screen. Video Presets Use this sub-menu to select one of four preset view options optimized for different viewing conditions.
Adjusting Video Presets 1 Use the keys to select Video Presets and press 2 Press the keys on the remote control to select the desired option. 3 Press to save and exit the screen. Sharpness Use Sharpness to adjust the sharpness or softness of the display. Adjusting Sharpness 1 Use the keys to select Sharpness and press...
Page 32
SETUP MENUS Adjusting Color Temperature 1 Use the keys to select Color temperature and press 2 Press the keys on the remote control to select the desired option. 3 Press to save and exit the screen. Use Hue to adjust the balance of the red, green, and blue colors in the display. Adjusting Hue 1 Use the keys to select Hue and press...
AUDIO Use the Audio sub-menus to configure the audio quality. These settings apply to the LCD TV speakers only. Any connected audio devices are not affected. Press on the remote control or Menu on the control panel to display the setup menu screen then select Audio to display the Audio sub-menu.
Page 34
SETUP MENUS Balance Use Balance to adjust the sound balance between the L/R speakers. Adjusting Balance 1 Use the keys to select Balance and press 2 Press the keys on the remote control to adjust the option level. 3 Press to save and exit the screen.
Page 35
Audio Preset Use this sub-menu to select one of four preset audio options optimized for different sounding conditions. The following options are available: • Rock: Sets the equalizer to the Rock mode. • Pop: Sets the equalizer to the Pop mode. •...
SETUP MENUS VIEW MODE Use the View Mode sub-menu to select the display's aspect ratio. Press on the remote control or Menu on the control panel to display the setup menu screen then select View Mode to display the View Mode sub-menu. The following options are available: Standard Picture is displayed in its original size.
Adjusting View Mode 1 Press the keys on the remote control to select the desired option. 2 Press to save and exit the screen. VIEW MODE (VGA) Select VGA as your input source and use the View Mode sub-menu to adjust the display in VGA mode.
SETUP MENUS Fine Tune Use this sub-menu to fine tune the display. 16:9 Fine Tune Auto Sync Use this sub-menu to synchronize the display automatically. 16:9 Auto Sync...
CHANNELS Use the Channels sub-menus to manage the channel list, language sound, and to scan for available TV channels in your area. Press on the remote control or Menu on the control panel to display the setup menu screen then select Channels to display the Channels sub-menu. The following options are available: Skip List, Channel Edit, MTS, Audio Language, Auto Search, and Manual Add.
SETUP MENUS Channel Edit Use Channel Edit to assign a name to a channel. Channel Name Edit :Select Editing Channel Names 1 Use the keys to select Channel Edit and press Name Edit screen appears. 2 Use the keys to select the desired channel and press the Edit Name screen.
Use MTS to select multichannel television sound. The following options are available: • Mono: Allows mono output (useful when stereo is noisy or inconsistent). • Stereo: Allows stereo sound for superior TV viewing experience. • SAP: Allows second audio program from the speakers while watching a scene in the original program.
SETUP MENUS Adjusting Audio Language 1 Use the keys to select Audio Language and press 2 Press the keys on the remote control to select English, French or Spanish. 3 Press to save and exit the screen. Auto Search Select Auto Search and press receivable channels for the source you select: •...
SETTINGS Use the Settings sub-menus to configure the LCD TV operational setup and view the current firmware version. Press on the remote control or Menu on the control panel to display the setup menu screen then select Settings to display the Settings sub-menu. The following options are available: Date and Time, Closed Captions, Parental Control, OSD Timeout, OSD Language, Power settings, and Reset All.
SETUP MENUS Adjusting Date and Time 1 Use the keys to select Date and Time and press 2 Use the keys to select Date or Current Time and press 3 Use the keys to select a date or time segment. 4 Use the keys to adjust the value.
• Size: Can be set to As Broadcaster, Small, Medium, or Large. • Font Color: Can be set to As Broadcaster, Black, White, Green, Blue, Red, Cyan, Yellow, or Magenta. • Background Color: Can be set to As Broadcaster, Black, White, Green, Blue, Red, Cyan, Yellow, or Magenta.
Page 46
SETUP MENUS 3 Press to save and exit the screen. • TV Rating: Use this sub-menu to customize US TV Rating programs. TV- Y (TV Rating) TV-Y TV-Y7 / FV TV-G TV-PG / V / S / L / D TV-14 / V / S / L / D TV-MA / V / S / L Rating...
Page 47
• MPAA Rating: Use this sub-menu to select the ratings of allowable movies. USA - Movies Rating Description Contains nothing most parents will consider offensive for even their youngest children to see or hear; suitable for young children. May contain some material parents might not like to expose to their young children-material that will clearly need to be examined or inquired about before children are allowed to view the film.
Page 48
SETUP MENUS • Canada English: Use this sub-menu to select the classification categories (based on Canadian ratings) of allowable TV programs and movies. en-C8 (Canada English Rating) Rating Description Suitable for viewing by children of all ages. Not suitable for children under 8 years of age.
Page 49
• Canada French: Use this sub-menu to select the ratings of allowable TV programs and movies. These ratings are based on the classification categories determined by La Régie du cinéma du Québec. fr-8+ (Canada French Rating) Rating 8 ans + 13 ans+ 16 ans+ 18 ans+...
Page 50
SETUP MENUS • Channel Block: Channel Block allows you to block channels. Adjusting Channel Block 1 Use the keys to select Channel Block and press 2 Use the keys to select the desired channel and press repeatedly to block or unblock. 3 Press to save and exit the screen.
OSD Timeout Use OSD Timeout to adjust the OSD duration on the screen: 10 sec, 20 sec, or 30 sec. Adjusting OSD Timeout 1 Use the keys to select OSD Timeout and press 2 Press the keys on the remote control to select 10 sec, 20 sec, or 30 sec.
Page 52
SETUP MENUS Power Settings Use this sub-menu to configure power-related settings for the LCD TV. Power Settings :Select The following options are available: • VGA port -DPMS: Use this setting to enable or disable VGA port -DPMS. • Backlight: Using this setting to select backlight options: Bright Room, Medium Room, and Dark Room.
Reset All Select Yes on this sub-menu to reset all LCD TV operational settings. Do this only if any of the following conditions occurs: • The system fails to respond to the remote control (make sure the remote control batteries are still working and that you are within the transmission range).
WALL MOUNT OPTION WALL MOUNT OPTION The LCD TV has been fitted with VESA FPMPMI compliant mounting holes. These 200 x 100 mm mounting holes allow the unit to be mounted on a wall. Use the four M6 x L10 mm screws to wall mount the LCD TV. WALL MOUNT INSTALLATION REMINDERS •...
TROUBLESHOOTING Problem Corrective Action • • No power Power is suddenly Make sure the sleep timer is turned off. turned off. Use Reset All in Settings menu to reset your Forgotten PIN password. • Remote control • does not work. •...
Page 56
TROUBLESHOOTING Problem Corrective Action • No picture or the No Signal message appears when a • VGA cable is connected. • Picture is cut off or appear in a sidebar Press screen. • • Poor image quality • in TV mode (cutoff picture, snowy images).
Page 57
Speakers option is set to Off in Audio menu. NOTES: If the problem condition persists even after performing the recommended corrective actions, contact us by: • Logging on to www.wde.com • Contacting the Westinghouse Customer Service at (800) 701-0680 or e-mail us at service@wde.com TROUBLESHOOTING...
SPECIFICATIONS SPECIFICATIONS Item Specification Model Name Cezanne 42 Active Area (Diagonal, mm) Resolution Brightness (Nits, typ) Panel Contrast Ratio (min) Response Time (min) Aspect Ratio Display color • • • Audio/Video • Input/Output • Terminals • • • Speaker Out 8W (2 channels) AV Timing 480i/p, 720p, 1080i...
Page 59
Item Specification Dimensions (WxHxD) Physical Specifications Weight (Net) Weight (Gross) NOTES: • These product specifications are subject to change without user notification. • Do not set your computer graphics card to exceed the unit’s refresh rates; doing so may cause damage to the LCD TV. SPECIFICATIONS With stand: 774x549x193 mm Without stand: 774x507x88 mm...