Troubleshooting; Side Burner Troubleshooting - Weber Summit 56211 Owner's Manual

PRobLEm
burners burn with a yellow or
orange flame, in conjunction with
the smell of gas (this is normal for
the burner lighting tube).
symptoms:
burners do not light. -or- burners
have a small flickering flame in the
hi position. -or-
barbecue temperature only reaches
250° to 300° in the hi position.
burner does not light, or flame is
low in hi position.
experiencing flare-ups:
m Caution: do not line
the bottom tray with
aluminum foil.
burner flame pattern is erratic.
flame is low when burner is on hi.
flames do not run the whole length
of the burner tube.
inside of lid appears to be "peeling."
(resembles paint peeling.)
Cabinet doors are not aligned.
if problems cannot be corrected by using these methods, please contact the Customer service representative in your area using the contact information on our
web site. log onto www.weber.com
PRobLEm
side burner does not light.
flame is low in hi position.
push button ignition does not work.
if problems cannot be corrected by using these methods, please contact the Customer service representative in your area using the contact information on our
web site. log onto www.weber.com

TRoUbLESHooTING

cHEcK
Inspect Spider/Insect screens for possible obstructions . (Blockage
of holes .)
The excess flow safety device, which is part of the barbecue to
cylinder connection, may have activated .
Is LP fuel low or empty?
Is fuel hose bent or kinked?
Does Burner light with a match?
Did you use the snap igniter several times until the main burner lit?
(See "MAIN BURNER IGNITION")
Does the igniter work (Do you see a spark when you repeatedly
use the snap igniter)?
Are you preheating barbecue in the prescribed manner?
Are the cooking grates and Flavorizer
burned-on grease?
Is the bottom tray "dirty" and not allowing grease to flow into catch
pan?
Are burners clean?
The lid is porcelain enamel or stainless steel, not paint . It cannot
"peel" . What you are seeing is baked on grease that has turned to
carbon and is flaking off .
this is not a defeCt.
Check the adjustment pin on the bottom of each door.
.
®

SIDE bURNER TRoUbLESHooTING

cHEcK
Is gas supply off?
The excess flow safety device, which is part of the barbecue to
cylinder connection, may have activated .
Is the fuel hose bent or kinked?
Does burner light with a match?
.
®
Clean Spider/Insect screens . (See "ANNUAL MAINTENANCE"
section)
To reset the excess flow safety device turn all burner control
knobs and the cylinder valve off . Disconnect the regulator from the
cylinder . Turn burner control knobs to HI . Wait at least 1 minute .
Turn burner control knobs to OFF . Reconnect the regulator to the
cylinder . Turn cylinder valve on slowly . Refer to "MAIN BURNER
IGNITION" .
Refill LP cylinder .
Straighten fuel hose .
Clean burners . (See "MAINTENANCE" section)
Make sure to hold the control knob in for two seconds after
snapping the igniter and seeing the orange flame from the burner
lighting tube .
Try manually lighting the burner (refer to "MAIN BURNER
MANUAL IGNITION") . Call customer service .
All burners on HI for 10 to 15 minutes for preheating .
bars heavily coated with Clean thoroughly . (See "CLEANING" section)
®
Clean bottom tray .
Clean burners . (See "MAINTENANCE" section)
Clean thoroughly . (See "CLEANING" section)
Loosen adjustment nut/s. Slide door/s until aligned. Tighten nut.
Turn supply on .
To reset the excess flow safety device turn all burner control
knobs and the cylinder valve off . Disconnect the regulator from the
cylinder . Turn burner control knobs to START/HI . Wait at least 1
minute . Turn burner control knobs to OFF . Reconnect the regulator
to the cylinder . Turn cylinder valve on slowly . Refer to "SIDE
BURNER IGNITION" .
Straighten hose .
If match lights burner, check igniter (See "SIDE BURNER
MAINTENANCE") .
SoLUTIoN
SoLUTIoN
WWW.WEbER.com
® 31