Related Manuals for Viessmann Vitocell 050-E
Summary of Contents for Viessmann Vitocell 050-E
- Page 1 VIESMANN Installation and service instructions for contractors Vitocell 050-E Type SVPA Heating water buffer cylinder 600, 750 and 950 l VITOCELL 050-E Please keep safe. 6153974 GB 7/2020...
- Page 2 Safety instructions Safety instructions Please follow these safety instruc- tions closely to prevent accidents and material losses. Safety instructions explained Danger Note This symbol warns against the risk Details identified by the word "Note" of injury. contain additional information. Please note This symbol warns against the risk of material losses and environmen- tal pollution.
- Page 3 Please note Repairing components that fulfil a safety function can compromise the safe operation of the system. Replace faulty components only with genuine Viessmann spare parts. Auxiliary components, spare and wearing parts Please note Spare and wearing parts that have...
-
Page 4: Table Of Contents
Index Index Information Disposal of packaging ................Symbols ....................Intended use ..................Product information ................System examples .................. Spare parts lists ..................Preparing for installation Connections ................... Siting ...................... Installation sequence Levelling the heating water buffer cylinder ..........Fitting the thermometer sensors and cylinder temperature sensors ..10 Fitting the thermal insulation .............. - Page 5 Information Disposal of packaging Please dispose of packaging waste in line with statu- tory regulations. Symbols Symbol Meaning Reference to other document containing further information Step in a diagram: The numbers correspond to the order in which the steps are carried out. Warning of material losses and environ- mental pollution Live electrical area...
- Page 6 ■ Capacity: 600, 750 and 950 l systems, solid fuel boilers and heat recovery. System examples Available system examples: See www.viessmann- schemes.com. Spare parts lists Information about spare parts can be found at www.viessmann.com/etapp or in the Viessmann...
- Page 7 Preparing for installation Connections Fig. 1 Back Heating water flow 1 Heating water flow 2/heating water return 1 Heating water return 2 Heating water return 3 Mounting for thermometer sensor (below thermal insulation) Clamping system for cylinder temperature sensor 1 (behind thermal insulation) Mounting for thermometer sensor (below thermal insulation) Clamping system for cylinder temperature sensor...
- Page 8 Preparing for installation Siting Please note Note To prevent material losses, install the heating Placing the heating water buffer cylinder on a plinth will water buffer cylinder in a room free from the risk make the room easier to clean. of frost and draughts.
- Page 9 Installation sequence Levelling the heating water buffer cylinder Note Seal connections that are not required with caps. Fig. 2 Type plate 3 adjustable feet 3. Insert the adjustable feet into the legs as far as they will go. Use the adjustable feet to level the cyl- inder body.
-
Page 10: Fitting The Thermometer Sensors And Cylinder Temperature Sensors
Installation sequence Fitting the thermometer sensors and cylinder temperature sensors Fig. 4 1. Route the leads of all available thermometer sen- 5. Tighten the nuts. sors to the cylinder through the small apertures in the thermal insulation mat. 6. Depending on where the sensor is being fitted: Insert the thermometer sensors and cylinder 2. -
Page 11: Fitting The Thermal Insulation
Installation sequence Fitting the thermal insulation Fitting the thermal insulation jacket sections Please note The thermal insulation must not come into con- tact with naked flames. Exercise caution when welding and brazing Note 2 people are required for the following work. ■... -
Page 12: Fitting The Cover
Fitting the cover Fig. 6 Type plate Connections on the heating water side Any number of Vitocell 050-E can be connected either Note in series or in parallel. Connection pipes and air vent For location of connections, see page 7. - Page 13 Commissioning/service reports Commissioning/service reports Commissioning Maintenance/service Maintenance/service Date: Maintenance/service Maintenance/service Maintenance/service Date: Maintenance/service Maintenance/service Maintenance/service Date: Maintenance/service Maintenance/service Maintenance/service Date: Maintenance/service Maintenance/service Maintenance/service Date:...
-
Page 14: Product Characteristics
Specification Product characteristics Vitocell 050-E Cylinder capacity Standby heat loss kWh/24 h 2.90 3.15 3.47 To EN 12897: 2016 with 45 K temperature differential Energy efficiency class Dimensions Length ( With thermal insulation ■ Excl. thermal insulation ■ Width excl. thermal insulation... -
Page 15: Final Decommissioning And Disposal
Disposal Final decommissioning and disposal Viessmann products can be recycled. Components For decommissioning the system, isolate the system and substances from the system are not part of ordi- from the power supply and allow components to cool nary household waste. - Page 16 Viessmann Werke GmbH & Co. KG Viessmann Limited D-35107 Allendorf Hortonwood 30, Telford Telephone: +49 6452 70-0 Shropshire, TF1 7YP, GB Fax: +49 6452 70-2780 Telephone: +44 1952 675000 www.viessmann.com Fax: +44 1952 675040 E-mail: info-uk@viessmann.com...