Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Exmark Manuals
  4. Lawn Mower
  5. LAZER Z DS Series
  6. Setup instructions

Exmark LAZER Z DS Series Setup Instructions

Hide thumbs Also See for LAZER Z DS Series:
1
2
3
4
5
6

Advertisement

Quick Links

Download this manual
This product contains a chemical or chemicals known to the State of California to
Diesel engine exhaust and some of its constituents are known to the State of California
Loose Parts
Use the chart below to verify that all parts have been shipped. Part numbers not shown are available on the dealer
extranet.
Dealer Pack
Part #
323-6
98-5975
3290-357
103-7599-03
109-2394
104-8301
104-8301
3231-7
103-2106
1-603511
Literature Pack
Manual, Operator's
Manual, Engine Operator's
Installing the Rollover Protection
System (Roll Bar)
1. Remove sides and top of crate from the base.
2. Remove roll bar components from the crate.
3. Remove roll bar tubes from sides of crate.
© 2013—Exmark Mfg. Co., Inc.
P.O. Box 808
Beatrice, NE 68310
Proposition 65 Warning
cause cancer, birth defects, or reproductive harm.
to cause cancer, birth defects, and other reproductive harm.
Description
Cap Screw, Hex 3/8-16 x 1 inch
Washer, Spring Disc
Nut, Hex Flange 3/8-16 inch
Guard
U-Bolt
Nut-Nyloc 3/8-16 Flg
Nut-Nyloc 3/8-16 Flg
Bolt-Carriage 3/8-16 x 2 1/4
Key, Exmark Logo
Key, Standard
LAZER Z
WARNING
CALIFORNIA
Qty.
8
8
8
1
2
4
6
6
1
1
4. Remove the two brackets used to mount the bottom
of the upper roll bar tube to the crate.
5. Remove the 1/2-13 x 3 1/4 inch capscrews and
1/2-13 inch hex flange lock nuts from the two
brackets at each end of the upper roll bar tube and
retain for later use (Figure 1).
DS-SERIES
®
Setup Instructions
For Serial Nos. 314,000,000 & Higher
Use
Installing the Rollover Protection
System (Roll Bar).
Installing the air cleaner guard.
Installing the side bumpers (Rear
Discharge Units Only).
Fill out the online warranty registration
form and place keys into literature
pack.
All Rights Reserved *4501-768* A
Part No. 4501-768 Rev. A
Printed in the USA.

Advertisement

loading

Related Manuals for Exmark LAZER Z DS Series

Summary of Contents for Exmark LAZER Z DS Series

  • Page 1 (Figure 1). 3. Remove roll bar tubes from sides of crate. © 2013—Exmark Mfg. Co., Inc. All Rights Reserved *4501-768* A Part No. 4501-768 Rev. A P.O.
  • Page 2 6. Remove the four 1/4 inch lag screws holding the wheel hub brackets to the crate bottom and discard. Figure 2 1. 3/8-16 x 1 inch capscrews 3. Wheel nuts 2. Spring disc washer (cone 4. 3/8-16 inch whizlock nuts towards capscrew head) Figure 1 1.

  • Page 3: Installing The Drive Wheels

    Installing the Drive Wheels 13. Lightly oil the inside surfaces of the ear-shaped plates at the upper end of the lower roll bar tubes 1. Remove the 1/2-20 inch drive wheel nuts (installed (Figure 3). on studs of drive motors; Figure 2) and retain for 14.
  • Page 4 Note: If the positive cable is also disconnected, DANGER connect the positive (red) cable to the positive Battery electrolyte contains sulfuric acid, which is battery terminal first, then the negative (black) cable poisonous and can cause severe burns. Swallowing to the negative battery terminal. Slip insulator boot electrolyte can be fatal or if it touches skin can over the positive terminal.

  • Page 5: Servicing The Engine

    The engine is shipped with oil; check oil level and if 3. Bushing 7. Notch necessary fill to the appropriate level. Exmark 4-Cycle 4. Lock washer Premium Engine Oil is recommended. Refer to the Engine Owner’s Manual for an acceptable alternative.
  • Page 6 2. Check hydraulic reservoir and if necessary fill the reservoir to the appropriate level with Exmark Premium Hydro oil. 3. Replace hydraulic reservoir cap and tighten until snug. Do Not overtighten.