TP-Link RE210 Quick Installation Manual

Quick
Installation
Guide
AC750 WiFi Range Extender
RE210
Two easy setup options:
ONE: Using a Web Browser
TWO: Using WPS (Wi-Fi Protected Setup)
1
Using a Web Browser
1 Power On
Plug the Range Extender into a wall outlet
close to your router, and wait until the Power
LED is lit and solid green.
Con gure
4
Follow the Quick Setup Wizard to manually con gure the Range Extender.
A. On the Start screen, click Next.
Start Choose Region
Main Router/AP WiFi Network Name(SSID):
Wi-Fi Network Name_2.4GHz:
Wi-Fi Network Name_5GHz:
Connection Status:
Please click Next to set up the Range Extender or click Exit to go to the Device Management Page.
D. Enter the main router's Wi-Fi password and
either choose Copy from Main Router/AP
or Customize to create a new network
name for the Extender. Click Next.
Start Choose Region
Main Router/AP Network (2.4GHz)
Main Router/AP WiFi Network Name(SSID):
Main Router/AP MAC Address(BSSID):
WiFi Security Option:
Fill in the WiFi Password of your Main
Range Extender Network (XXGHz)
Range Extender WiFi Network Name(SSID):
5 Relocate
In general, place your WiFi Range Extender about
halfway between your wireless router/AP and
wireless devices.
After moving to a new location, the Extender will
automatically reconnect to your router in
approximately one minute. If possible, try to
place your Range Extender in a location where
the LED is Green.
2
B. Choose your region from the Region drop-down
Wireless Settings Review Settings
N/A
N/A
Disconnected
Exit Next
E. Select your router's 5GHz wireless network. Click
Wireless Settings Review Settings
TP-LINK_2.4GHz_XXX
00-0A-EB-74-06-06
Most Secure(WPA-PSK/WPA2-PSK)
123456789
Router/AP:
Copy from Main Router/AP TP-LINK_2.4GHz_XXX
Customize TP-LINK_2.4GHz_XXX_EXT
Back Next
LEDs
(WPS)
Flashing green: The Range Extender is
establishing a secure connection or being
con gured via web page.
Solid green: The Range Extender has established
a secure connection, and the signal strength is
adequate.
Solid orange: The Range Extender has established
a secure connection, but the signal strength is
too strong.
Solid red: The Range Extender has established a
secure connection, but the signal strength is too
weak.
O : No active connection.
Connect
Disconnect your Ethernet connection. Click the
Wi-Fi icon on the system tray, select the
Extender's default wireless network name (e.g.
TP-LINK_Extender_XXGHz). No password is
required to connect the rst time.
Not connected
Connection are available
Wireless Network Connection
TP-LINK_Extender_XXGHz
Connect automatically Connect
√
list, and click Next.
Note: Per FCC regulations, all Wi-Fi products marketed in
the U.S. must be xed to the U.S. region only.
Start Choose Region Wireless Settings
Region: Please Select Your Region
Please select your own region to prevent illegal usage against the local law.
Exit Next
Next and repeat step D. Click Next to continue.
Start Choose Region Wireless Settings
Main Router/AP Network (5GHz)
Main Router/AP WiFi Network Name(SSID): TP-LINK_5GHz_XXX
Main Router/AP MAC Address(BSSID):
00-0A-EB-74-06-06
WiFi Security Option:
Most Secure(WPA-PSK/WPA2-PSK)
Fill in the WiFi Password of your Main
123456789
Router/AP:
Range Extender Network (XXGHz)
Range Extender WiFi Network Name(SSID): Copy from Main Router/AP
Customize
Back Next
YourNetworkName
and password
The Range Extender shares your router's Wi-Fi password for both 2.4GHz and 5GHz networks, but
may have di erent wireless network names if you customize the names during the con guration.
On: The Range Extender is connected to the 2.4G
wireless network of your main Router/AP.
O : The Range Extender isn't connected to your
main Router/AP.
On: The Range Extender is connected to the 5G
wireless network of your main Router/AP.
O : The Range Extender isn't connected to your
main Router/AP.
On: The Range Extender is on.
O : The Range Extender is o .
Flashing: The Range Extender is initializing.
Login
3
Launch a web browser and type
http://tplinkrepeater.net
Use admin (all lowercase) for both Username
and Password to login.
http://tplinkrepeater.net
Username:
Password:
C. Select your router's 2.4G wireless network
name (SSID) and click Next. If the SSID is
hidden, select the Set SSID and MAC
manually option.
Review Settings
Start
Available Wireless Networks (2.4GHz): 24
Choose SSID
TP-LINK_2.4GHz_XXX
√
TP-LINK_XXX
Set SSID and MAC Manually
F. Verify your Wireless Settings and click Finish.
Both 2.4G and 5G LEDs should turn on and stay
solid green.
Review Settings
Start
Wireless Setting
Main Router/AP WiFi Network Name (2.4GHz):
Main Router/AP WiFi Network Name (5GHz):
Range Extender WiFi Network Name (2.4GHz):
Range Extender WiFi Network Name (5GHz):
TP-LINK_5GHz_XXX
TP-LINK_5GHz_XXX_EXT
Export Settings
YourNetworkName or
YourNetworkName_EXT
and password
5G
2.4G
Ideal Range Extender Placement
(2.4G)
(5G)
(Power)
in the address eld.
admin
admin
Login Cancel
Choose Region Wireless Settings Review Settings
Signal MAC Channel Security
00-0A-EB-74-06-06 1 WPA-PSK
0C-72-2C-B3-A5-2C 1 WPA-PSK
Back Rescan Next
Choose Region Wireless Settings Review Settings
TP-LINK_2.4GHz_XXX
TP-LINK_5GHz_XXX
TP-LINK_2.4GHz_XXX_EXT
WiFi Security Option: Most Secure (WPA/WPA2-PSK)
WiFi Password: 123456789
TP-LINK_5GHz_XXX_EXT
WiFi Security Option: Most Secure (WPA/WPA2-PSK)
WiFi Password: 123456789
Back Finish