Advertisement
Quick Links
Grass Basket Kit
For Reelmaster
Model No. 03662
Installation
Loose Parts
Use the chart below to verify that all parts have been shipped.
Procedure
1
2
3
4
5
6
7
Important: To gain additional clearance for the rear baskets when raising the cutting units, install the Rear Lift
Cylinder Limit Kit.
© 2015—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
5010 Series Cutting Units with 5in and 7in Reels
Description
Cylinder collar
Bolt
Flanged locknut
Spacer
Stop bracket
Carriage bolt
Basket guide
Basket bracket
Roll pin
Washer
Left-hand torsion-spring (gold)
Right-hand torsion-spring (black)
Basket collar
Flat washer (0.344 x 0.875)
Bolt (5/16 x 1–1/4 inch)
Bolt (5/16 x 1/2 inch)
Plastic washer
Cut-off bar
Bolt (1/4 x 1–3/4 inches)
Locknut (1/4 inch)
No parts required
Flanged locknut
Basket assembly
No parts required
Register at www.Toro.com.
Form No. 3386-464 Rev B
Installation Instructions
Qty.
4
4
8
Install the rear lift cylinder limit kit
(ordered separately).
2
2
4
1
1
1
1
1
1
Install the basket guides and brackets.
1
2
1
1
1
1
4
Install the cut-off bar.
4
–
Remove the 4 grass deflectors.
Remove the support tube (for 5–inch
2
diameter reels only).
Mount the basket assembly to the
1
cutting unit.
–
Adjust the basket position.
Original Instructions (EN)
All Rights Reserved *3386-464* B
Printed in the USA
Use
Advertisement
Related Manuals for Toro 03662
Summary of Contents for Toro 03662
- Page 1 Form No. 3386-464 Rev B Grass Basket Kit For Reelmaster ® 5010 Series Cutting Units with 5in and 7in Reels Model No. 03662 Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped.
- Page 2 Stop bracket Carriage bolt For 7-inch Diameter Reels Note: The Rear Lift Cylinder Limit Kit (Toro part no. 110–9604) is ordered separately. Contact an Authorized Toro Dealer to order the kit. 1. Position the traction unit on a level surface, lower the lift arms/cutting units, and stop the machine.
- Page 3 1/2 inch) and flat washer (0.344 x 0.875). Position the components as shown in Figure Installing the Basket Guides and Brackets Parts needed for this procedure: Basket guide Basket bracket Roll pin Figure 3 Washer 1. Carrier frame 3. Flat washer (0.344 x Left-hand torsion-spring (gold) 0.875) Right-hand torsion-spring (black)
- Page 4 and the shorter, rear leg of the spring is to be inserted into the hole in the basket bracket. 6. Check if the bracket basket rotates freely. Important: The plastic washer must be installed Removing the 4 Grass onto the basket collar to prevent binding. Deflectors No Parts Required Procedure...
- Page 5 Mounting the Basket Assembly to the Cutting Unit Parts needed for this procedure: Basket assembly Procedure Figure 6 1. Support tube 3. Flange-head bolt Mount a basket to each cutting-unit carrier-frame by inserting 2. Carrier frame 4. Flanged locknut (3/8 inch) the basket-mounting pin into the basket-guide bracket and depressing the opposite mounting pin into the pivoting-basket bracket...
- Page 6 Adjusting the Basket Position No Parts Required Procedure Make sure that the basket is parallel to the cutting unit with a minimum clearance of 6 mm (0.250 inches) between the lip of the basket and the reel. If an adjustment to the basket position is required, proceed as follows: 1.
- Page 7 Notes:...