Panasonic KX-TDA200BX Service Manual page 51

11.4.2. List of Errors and Solutions
The tables below list the errors and their solutions.
When an error whose error code is indicated with "*" occurs in the main unit (Hybrid IP-PBX), the ALARM indicator on the front
of the cabinet turns on red, and the system logs the error information.
When the error conditions indicated by the error codes "021", "091", "230", and "510" are recovered, the ALARM indicator will
turn off automatically, indicating successful troubleshooting. When other errors are logged, the ALARM indicator will turn off
only when the log for major or minor errors is cleared from the KX-TDA Maintenance Console.
In other words, the ALARM indicator will turn off under the following conditions:
· When the errors "021", "091", "230", and "510" are logged: when the error conditions are recovered
· When other errors are logged: when the log for major or minor errors is cleared from the KX-TDA Maintenance Console
Error Code Error Message
100 SRAM readwrite error
101 Flash write error
102 Flash boot check error
103 SDRAM eadwrite error
104 ASIC local bus register
access error
105 ASIC CT bus HW NG
106 ASIC Local HW0 NG
108 SD card not mounted
109 ASIC HDLC error
110 ASIC DMAC error
Error Code Error Message
210 ASIC local bus register
access error
211 Speech path loop-back
check error
212 Echo cancellor access
error
213 CSINF frame
error
214 DSP Boot check error
215 Framer IC access error
216 MSG card DSP error
217 MSG card data error
218 LANC register access
error
All manuals and user guides at all-guides.com
MPR Card Initial Self Diagnosis
PROBABLE CAUSE
· MPR card malfunction
· SD Memory Card not installed
· Defective data in SD Memory Card
· MPR card malfunction
· MPR card malfunction
LPR (Optional Service Card with Local Processor) Initial Self Diagnosis
PROBABLE CAUSE
· Optional service card malfunction:
DHLC, DLC, CSIF, T1, PRI, OPB3,
CTI-LINK, E&M, IP-GW
· Optional service card malfunction:
DHLC, DLC, SLC, CSIF, LCOT,
T1, PRI, OPB3, CTI-LINK, E&M,
IP-GW
· Optional service card malfunction:
CSIF, ECHO
sync.
· Optional service card malfunction:
T1
· Optional service card malfunction:
T1, PRI
· Optional service card malfunction:
MSG, OPB3
· Optional service card malfunction:
MSG, OPB3
· Erroneous recording of messages
· Optional service card malfunction:
CTI-LINK
· See if the MPR card is installed properly
· Press the Reset Button
· Replace the MPR card (be sure to turn off the main unit
(Hybrid IP-PBX) when replacing)
· See if the SD Memory Card is installed properly
· Replace the SD Memory Card
· Replace the MPR card (be sure to turn off the main unit
(Hybrid IP-PBX) when replacing)
· See if the MPR card is installed properly
· Press the Reset Button
· Replace the MPR card (be sure to turn off the main unit
(Hybrid IP-PBX) when replacing)
· See if the corresponding optional service card is installed
properly
· Pull out and re-insert the corresponding optional service
card
· Press the Reset Button
· Replace the corresponding optional service card
· See if the corresponding optional service card is installed
properly
· Pull out and re-insert the corresponding optional service
card
· Press the Reset Button
· Re-record the messages
· Replace the corresponding optional service card
· See if the corresponding optional service card is installed
properly
· Pull out and re-insert the corresponding optional service
card
· Press the Reset Button
· Replace the corresponding optional service card
51
KX-TDA200BX
SOLUTION
SOLUTION