Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Viper 64602210 150.2
Summary of Contents for Viper 64602210 150.2
- Page 1 model 150.2...
- Page 2 © 2002 Directed Electronics, Inc...
-
Page 3: Table Of Contents
Featuring high-efficiency MOSFET power supplies, flexible on-board crossovers, and state of the art audio design, Viper Audio power amplifiers will excite and TABLE OF CONTENTS Limited Two-Year Consumer Warranty ......4 Features . -
Page 4: Limited Two-Year Consumer Warranty
LIMITED TWO-YEAR CONSUMER WARRANTY Directed Electronics, Inc. promises to the original purchaser, to replace this product should it prove to be defective in workman- ship or material under normal use, for a period of two years from the date of purchase by the dealer as indicated by the date code marking of the product PROVIDED the product was installed by an... -
Page 5: Features
LED. Rugged one-piece extruded heat sink finished with injection-molded mounting feet. The Viper logo and Viper badge are four-way adjustable for a custom look. They may also impair a driver’s ability to hear traffic sounds or emergency vehi- cles. -
Page 6: Installation Guidelines
INSTALLATION GUIDELINES 1. Please read this owner’s manual carefully before installing this ampli- fier. 2. Disconnect the battery ground terminal prior to making any elec- trical connections. 3. Check for any hazards or obstruc- tions such as gas tanks, fuel or brake lines, and wiring harnesses before mounting the amplifier. -
Page 7: Wire Connector Plugs
10. Due to the high-frequency MOSFET WIRE CONNECTOR PLUGS Power and speaker wire connections on Viper Audio power amplifiers are performed with the use of specially designed connectors that allow for ease of wire termination and installation convenience. -
Page 8: Front Panel Connections/Controls
FRONT PANEL CONNECTIONS/CONTROLS 1. R R C C A A O O u u t t p p u u t t J J a a c c k k s s - These pass through RCA jacks can be used to send a signal to a second amplifier. -
Page 9: Rear Panel Connections
REAR PANEL CONNECTIONS 1. S S p p e e a a k k e e r r O O u u t t T T e e r r m m i i n n a a l l s s - Connect the speakers to these terminals. -
Page 10: Top Panel Features
Viper Badge Mounting The Viper Badge can be rotated in 90- degree increments to accommodate the amplifier’s final mounting position. 1. Determine the final mounting posi- tion of the amplifier. -
Page 11: Speaker Wiring Diagrams
SPEAKER WIRING DIAGRAMS Stereo operation (bottom view) Mono operation (bottom view) Simultaneous stereo/mono operation (bottom view) © 2002 Directed Electronics, Inc... -
Page 12: Crossover Settings And Gain Adjustment
CROSSOVER SETTINGS AND GAIN ADJUSTMENT Your Viper Audio power amplifier needs to be adjusted carefully to achieve maximum performance. These are some guidelines to follow when fine-tuning the amplifier. For full-range and simultaneous stereo/mono bass applications, the crossover selection switch should be set to FLAT. If the amplifier is driving your subwoofers, set the switch to LPF, and for mid-bass/midrange output, set to HPF. -
Page 13: Specifications
Output Impedance Supply Voltage Fusing and Power Minimum Cable Requirements (AWG) (Per amp, trunk mounted) © 2002 Directed Electronics, Inc Viper model 150.2 50 watts 75 watts 150 watts 200 watts Greater than 95 dB 20-20,000 Hz ± 0.5 dB... - Page 16 Directed Electronics, Inc. Vista, California 92083 www.directed.com Quality Directed products are sold and serviced throughout North America and around the world Call 800 274 0200 for more information about our products and services © 2002 Directed Electronics, Inc. - All rights reserved - G46022 02/02 The company behind this system is Directed Electronics, Inc.