Channel 4 Timer Control Output; Power On Memonry - Autopage 6876 Owner's Manual

F
Press and hold button of LCD remote until 2 beeps sound , release and re-press
LCD remote will show "CH 3" icon flash, then press
T.

CHANNEL 4 TIMER CONTROL OUTPUT

Press the transmitter and
F
Press and hold button of LCD remote until 2 beeps sound , release and re-press
LCD remote will show "CH 4" icon flash, then press
Channel 4 is user-programmable timer output. You may program the built-in timer to send a ground signal for any time
duration from 1 second to 120 seconds. For instance, this timer output may be used to turn on the headlight, power
window or sunroof. (Factory defaults setting at momentary output.)
U. POWER SAVER MODE (Default OFF)
Under Menu mode press
the power save mode, the LCD remote transceiver use "0" current to save the battery power. Press
Power save OFF
Exit: Press any button of the LCD remote transmitter to exit "Power Save Mode".
V. POWER ON MEMONRY:
This security system is equipped with circuitry that will allow the unit to remember its alarm state if the
power is lost and then reconnected.
W. SECOND VEHICLE SECURITY OPERATION:
Your 5-button remote transmitter can be utilized to control a second vehicle security system, To program the remote
control transmitter to a second vehicle, follow the instructions for Transmitter programming.
* For the standard transmitter (II) is shift button.
1. Prior to pushing any button on the transmitter. Press the Select II button first on the transmitter.
2. Once II button is pressed the LED on the transmitter will illuminate for 3 seconds to indicate the second transmitter
pin code has built-in.
3. While the LED is illuminated, press any button on the remote control transmitter to control a second vehicle security
system.
** For LCD transceiver – 2
F
a. Press and hold button of LCD remote for 1 second until 2 beeps sound, then release the
b. The text will flash on the LCD screen, press
c. Press or button to move up or down in the menu, find CAR SELECT on the menu.
d. Press button to select the option you would like to adjust CAR 1 or CAR 2 for further operation.
X. CHECK VEHICLE'S VOLTAGE:
Press button while VOLTAGE
on the LCD screen. Please note that this data is for your reference only. Please check the exact data on
vehicle.
A. TO REMOTE START THE VEHICLE:
When you want to start your vehicle,
1. Press button once on the transmitter.
2. The parking light will activate to indicate the remote start received the signal.
3. The engine will start in approximately 5 seconds.
4. Once the engine is running, after couple seconds the parking lights will turn on and the climate controls
will activate and adjust the vehicle's interior temperature to your preset setting. (While the vehicle is
running, the "minutes" digit on the LCD screen will flash and the will indicate count down timer based on
the 5, 10, 20 or 30 minute run time set up by your installation center.)
5. The vehicle will run for a programmable 5 to 30 minute cycle before shutting down. (When the unit
shuts off the count down timer will turn off and the transmitter will play a melody.)
NOTE: The Remote Start Unit will not start the vehicle if any one of the following conditions exists:
1. The hood is opened.
2. The brake pedal is pressed.
3. The optional remote start enable toggle is switched to the "OFF" position. (If installed)
4. The gear selector is in any gear other then "PARK" or "NEUTRAL"
SAFE START (Child safety mode)
Factory default is set to press the
to eliminate an accidental remote start:
1. The user presses the transmitter
2. The user presses the transmitter
NOTE: Contact your installing dealer to activate this feature.
buttons at the same time to active Channel 4 function.
button while "POWER SAVE" icon flash, press
nd
car operation :
REMOTE START OPERATION:
button once on the transmitter to start the vehicle. You can program this feature
buttons twice within 3 seconds to start the vehicle. or
and buttons at the same time to start the vehicle.
to activate channel 3 function.
button
to activate channel 4 function.
button
button to enter the menu.
icon flash (see Table 3); the vehicle's voltage will be shown
9
F
button again
or
F
button twice
button Power save ON, while
button
F
button.
the
the