Autopage 6876 Owner's Manual
  1. Manuals
  2. Brands
  3. Autopage Manuals
  4. Controller
  5. 6876
  6. Owner's manual
Autopage 6876 Owner's Manual

Autopage 6876 Owner's Manual

Remote engine starter with alarm system
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
A. BATTERY REPLACEMENT:
This system needs no specific maintenance beyond remote control battery replacement. The 2-way
remote is powered by a 1.5V AAA battery. The 1-way remote is powered by a pair of 3V, CR2032 battery
Battery Level Indicator (2-way remote)
The Battery Level indicator has three level indicators that serve as a visual indication of battery charge.
When the battery reaches a low charge level that requires replacement, the remote control will generate
a single notification chirp, and the Battery Level indicator
Gently pull the end of the battery door away from the top of the remote control then slide the door up to
expose the battery and remove the expired battery. Place the new battery into the remote. When power is
returned the remote control will display all icons in the LCD and generate all beeper tones once. Press
any button on the remote to terminate the beeper tone review.
B. STANDARD LCD ICON CONFIGURATIONS:
The lock icon will be displayed when
the door locked.
Sensor Bypass
Sensor 1bypass under Arm mode
Valet Mode
Remote start and alarm functions shall
be temporarily on hold.
Hood Trigger
Hood is illegally opened (Zone 1)
Door Open Warning
Doors are illegally opened (Zone 3)
REMOTE ENGINE STARTER
WITH ALARM SYSTEM
OWNER'S MANUAL
LCD REMOTE CONTROL TRANSCEIVER
will flash continuously.
The unlock icon will be displayed
when the door unlock
Hidden Alarm Mode
The security system arm with hidden
alarm function
Trunk Trigger
Trunk is illegally opened (Zone 2)
Sensor Trigger
Trigger on Sensor 1 (Zone 4)
1
:

Advertisement

Table of Contents
loading

Summary of Contents for Autopage 6876

  • Page 1 REMOTE ENGINE STARTER WITH ALARM SYSTEM OWNER’S MANUAL LCD REMOTE CONTROL TRANSCEIVER A. BATTERY REPLACEMENT: This system needs no specific maintenance beyond remote control battery replacement. The 2-way remote is powered by a 1.5V AAA battery. The 1-way remote is powered by a pair of 3V, CR2032 battery Battery Level Indicator (2-way remote) The Battery Level indicator has three level indicators that serve as a visual indication of battery charge.

  • Page 2: Hidden Alarm

    Ignition Trigger Ignition switch is illegally turned on System trigger (Zone 5) Remote Transmission In – Range Indicator You are transmitting the signal to Your are within the remote control range. control unit Icon flash under check mode Anti Car-Jack Mode Activate the anti car-jacking mode Engine Cranking Engine Running...
  • Page 3 until 2 beeps sounded Press three times Press button to activate channel CH 3 within 5 seconds flashing 4 functions. CH 4 Press four times within flashing Press button to activate channel 5 seconds 5 function Table 3: three beeps to confirm Button LCD display Button...
  • Page 4 - Toggle - Enables parking countdown. Parking There is a beep 5 min. before the Parking countdown countdown reaches 0. - Disables parking countdown. Illumination Default is Menu 3 SEC. - Toggle Basic operation with backlight 5 SEC . or Illumination Illumination 3 SEC.

  • Page 5: Remote Transmitter Operation

    - Toggle power - While the power save mode, the LCD save remote transceiver uses “0” current to save the battery power. - Power save OFF Exit: Press any button of the LCD remote transmitter to exit the “Power Save Mode”. Daily Start Timer Daily Start Time Adjust Only (ex.

  • Page 6: Passive Arming

    5. Panic Alarming Flashes Flashes 6. Car-Jacking Alarming Flashes Disable Flashes 7. Car Locator 6 Chirps 12 Flashes Locking E. ACTIVE ARMING – LOCK & ARM: button 1. Press on the transmitter. The siren will chirp once and parking light will flash once indicating that the system is now armed. The vehicle’s doors will lock upon arming if interfaced with the security system.

  • Page 7: Valet Mode

    above procedures, system's siren will stop alarming, lights will stop flashing, but the vehicle can’t be started.) 3. Within 15 seconds of the last digit code enter (the 1st code), then turn the Ignition Switch “OFF” and then “ON”. Within 15 seconds, enter your chosen second digit code by pressing and releasing the Valet Switch. 5.
  • Page 8 “Noise Abatement Circuit” covers doors (Hood/Trunk) differently: If the alarm is triggered by an open door for six full cycles, the doors will be bypassed until the trigger ceases. M. ANTI CAR- JACKING Warning: If you don't need the car jacking function in this alarm system, be sure to set car jacking feature “OFF”.

  • Page 9: Channel 4 Timer Control Output

    Press and hold button of LCD remote until 2 beeps sound , release and re-press button again LCD remote will show “CH 3” icon flash, then press to activate channel 3 function. button CHANNEL 4 TIMER CONTROL OUTPUT Press the transmitter buttons at the same time to active Channel 4 function.

  • Page 10: Temporary Stop Feature

    B. OPERATE THE VEHICLE WHILE RUNNING FROM THE REMOTE START: To operate the vehicle while engine running from the remote start, 1. Insert the ignition key and turn it to “ON” (not the start) position. 2. Press the brake pedal. Note: If the brake pedal is pressed before the key is in the ON position, the engine will shut down.

  • Page 11: To Turn Off The Remote Start

    F” Press the transmitter “ buttons first, within 3 seconds press button; the in-door temperature will be shown on the LCD screen. This reading may be higher than actual ambient temperature due to the greenhouse and is relative only the inside vehicle temperature. G.

Table of Contents