Summary of Contents for John Lewis Napoli 80310606
Page 1
Please check the pack contents before attempting to assemble this product.A full checklist of compo- nents is given in this leaflet. If any components are missing, please contact the John Lewis Helpline. This product is HEAVY, it should be assembled as near as possible to the point of use. TAKE CARE WHEN LIFTING to avoid personal injury and (or) damage to the product.
Page 2
Fittings checklist Metal dowel x 27 Long cam lock x 23 Short cam lock x 4 30mm 30mm 40mm Wooden dowel x 8 Wooden dowel x 16 Wooden dowel x 4 Conformat x 4 11mm Euroscrew x 8 16mm Screw x 8 Support foot x 4 30mm Screw x 4 Arm x 2...
Page 4
Step by step assembly instructions Step One Place the cam lock (B) into the holes on panels (3) (4), arrow pointing towards the bolt. ttach 8x wooden dowels (E) into the pre-drilled holes as shown. Step Two ttach 8x metal dowels ( ) into the pre-drilled holes on side panels (1) (2) as shown. Use a screwdriver to turn fitting ( ) clockwise to fix.
Page 5
Step by step assembly instructions Step Three ttach panels (3) (4) onto side panels (1) as shown. Ensure metal dowels ( ) and wooden dowels (E) are aligned correctly with the holes of matching parts before attaching. Secure panels using a screwdriver to turn fitting (B) clockwise to fix. Step Four ttach side panels (2) onto panels (3) (4) as shown.
Page 6
Step by step assembly instructions Step Five ttach 4x wooden dowels (E) into the pre-drilled holes of panels (14)(15) as shown. ttach 8x wooden dowels (D) into the pre-drilled holes of panels (16)(17) as shown. Place the cam lock (B) into the holes on panels (14) (15) arrow pointing towards the bolt.
Page 7
Step by step assembly instructions Step Seven ttach panel (16) onto panel (3) Ensure wooden dowels (D) are aligned correctly with the holes of match- ing parts before attaching. Step Eight ttach panel (17) onto panel (16) as shown. Ensure wooden dowels (D are aligned correctly with the holes of matching parts before attaching.
Page 8
Step by step assembly instructions Step Nine Fix panel (15) onto bottom panel (4) using 2x conformat screws (G) and allen key (R). Step Ten ttach 5x metal dowels ( ) into the pre-drilled holes on panel(13). Use a screwdriver to turn fitting ( ) clockwise to fix, repeat for all drawers.
Page 9
Step by step assembly instructions Step Twelve Fix runner parts (O1) (O2) to the panels (14) (15) through holes shown in the detail view using 4x euroscrews (H). Step Thirteen ttach 10x metal dowels ( ) into the pre-drilled holes on panels. Use a screwdriver to turn fitting ( ) clockwise to fix.
Page 10
Step by step assembly instructions Step Fourteen ttach panels as shown. Ensure wooden dowels are aligned correctly with the holes of matching parts before attaching. Step Fifteen Position panels as shown, turn locking nuts (B) clockwise to lock. Page 10 NAN 04/14...
Page 11
Step by step assembly instructions Step Sixteen Fix plastic hinge (P) to mirror panel (8) using screw (Q) Fix mirror panel (8) to desk using plastic hinge (P) and screw (Q) Step Seventeen Fix the two rms (N) using 8x screws (I) ttach bumpers (S) LIFT STAY ASSEMBLY Make sure triangle plate is positioned as...
Page 12
Step by step assembly instructions Step Eighteen ttach 2x wooden dowels (E) into the pre-drilled holes on drawer backs (11) as shown. Place the cam lock (C) into the holes on drawer sides (9) (10) as shown, arrow pointing towards the bolt. ttach 2x metal dowels ( ) into the pre-drilled holes on drawer front (12).
Page 13
Step by step assembly instructions Step Twenty Slide drawer bottom panel (18) into the drawer box grooves. Position drawer front (12) onto drawer box, turn locking nuts (C) clockwise to lock. Repeat for all drawers. Step Twenty-one Pull out the runners, then ensure plastic securing pegs are to the OUT position. Page 13 NAN 04/14...
Page 14
Step by step assembly instructions Step Twenty-two Slide the drawer box tilted until the stop. ttach the drawer box leaning on the runners. Push the plastic securing pegs in the IN position Page 14 NAN 04/14...
Page 15
Step by step assembly instructions Step Twenty-three Use the small plastic knob of the runners to align the drawers if needed. Step Twenty-four To prevent possible overbalancing we recommend that this unit is secured to a suitable wall by using appropriate wall plug and screw (not included) and the two holes into back panel (3). See wall fixings guide at the end of booklet.
It must under no circumstances be used free-standing. No liability will be accepted for damage or injury caused by inadequate fixing or use without fixing. PLEASE KEEPTHESE INSTRUCTIONS FOR FUTURE REFERENCE John Lewis Partnership 171Victoria Street London SWIE 5NN www.johnlewis.com Page 16...