Related Manuals for Uniden GPS105
Summary of Contents for Uniden GPS105
- Page 1 GPS105 Operating Manual & Quick Start Guide GPS Transceiver with an Integrated UHF Radio To bring outstanding wireless communication products to people's lives throughout the world.
-
Page 2: Warnings & Notifications
WARNINGS & NOTIFICATIONS When using the GPS105 in a motor vehicle it is the user's responsibility to ensure operating the GPS105 does not detract from the safe operation of the vehicle. For safety reasons it is not recommended that a driver change any settings while in motion. -
Page 3: Installing Your Gps105
Quick Start Guide The Quick Start Guide pages are designed to allow you to install and operate your GPS105 as quickly as possible, however it does not attempt to explain any of the advanced features of the GPS105 unit. INSTALLING YOUR GPS105 Please consider the following before installing. -
Page 4: Connecting Your Gps105
CONNECTING YOUR GPS105 BACK PANEL UHF ANTENNA CONNECTOR GPS ANTENNA CONNECTOR i. Remove fuse from fuse holder along power lead. ii. Connect 13.8V supply to the power lead making sure positive is applied to the red wire and ground to the black wire. -
Page 5: Test For A Gps Signal
TEST FOR A GPS SIGNAL Turn the GPS105 ON. ii. The Welcome display will appear. iii. After 3 seconds the initial display will switch to the UHF-CB display. iv. At the top of the display the unit will indicate it is searching for satellite information. -
Page 6: Setting User Name
SETTING USER NAME You may personalize your GPS105 by setting a User name which will appear at the top of the display. The User name also forms part of your call ID when communicating to radios using similar technology (GPS105 or GPS205) on channel 22 or 23. -
Page 7: Send Position On
SEND POSITION ON The SEND POSITION function enables the GPS105 to transmit your User name and position on channels 22 and 23. The factory setting for this feature is OFF. Current regulations permit enabling the SEND POSITION function to operate on Channels 22 and 23 only. -
Page 8: Table Of Contents
Setting User Name... Send Position ON... Contents... Introduction... Features... Controls... Indicators... Included With Your GPS105... UHF-CB Operation... Setting The Squelch... Selecting A Channel... To Transmit And Receive... To Operate In Duplex Mode (Repeaters)...9 Scanning with Priority Channel...10 Scanning - Scan Memory...10 Reply Delay...10... - Page 9 CONTENTS GPS Operation... Speed Warning... Early Warning Safety Alerts... Warning Volume... Caller Display... CALLER ID Memories...15 To Store The Caller Into MY POI...15 Mark Location...16 Quick Access Locations...16 MY POI Locations...17 Edit/Delete MY POI...18 Add Or Delete Safety Alert...19 Navigation...20 Navigate To Quick Access...21 Navigate To CALLER...21 Navigate To MY POI...22...
-
Page 10: Introduction
The Uniden GPS105 is designed to provide you with years of trouble free service. It's rugged components and materials are capable of withstanding harsh environments. We are certain that you will enjoy your GPS105. Please read this operating Manual carefully to ensure you gain the optimum performance of the unit. -
Page 11: Controls
CONTROLS GPS105 LCD Display /MEM - Scan Key/Memory Key SCAN - Navigation Key NAVI VOL/SQ - Centre Knob (Power-VOLUME): Turns the Power ON/OFF and adjusts the Volume. Outer Ring (SQUELCH): Adjusts the Squelch PTT - Push to Talk(PTT) switch Channel Instant - Instant Channel switch... -
Page 12: Indicators
INDICATORS 12 13 UHF-CB Display 11 GPS - GPS status icon 12 USER NAME - An example (MICHAEL) is shown 13 BUSY - Receive icon 14 INSTANT - Channel Instant icon 15 DUPLEX icon 16 MEMORY icon 17 CTCSS icon 18 SCAN icon 19 CTCSS Channel indicator 20 Channel indicator... -
Page 13: Included With Your Gps105
INCLUDED WITH YOUR GPS105 GPS105 Owners Manual Microphone Mounting Bracket, Knobs, Microphone Hanger Screws Rubber washer, Washer Stars and washers and Screws. DC Power Cord with fuse GPS Internal Antenna If any of these items are missing from the box, contact your dealer immediately. -
Page 14: Uhf-Cb Operation
UHF CB - OPERATION All UHF-CB functions are only available when in UHF-CB mode. SETTING THE SQUELCH 1. To turn the unit ON, rotate VOL knob clockwise. Adjust volume to a comfortable level. 2. Think of the Squelch control as a gate. If you turn SQUELCH fully clockwise it raises the "Squelch Gate"... -
Page 15: Selecting A Channel
UHF CB - OPERATION SELECTING A CHANNEL The GPS 105 uses the 40 UHF-CB Channels. For your reference a list of the available channels and corresponding frequencies is printed on page 26. To select a desired channel in UHF-CB Mode: 1. -
Page 16: To Operate In Duplex Mode (Repeaters)
UHF CB - OPERATION TO OPERATE IN DUPLEX MODE (REPEATERS) The Duplex function enables you to access local repeater stations. You can only activate Duplex from CH01-CH08. UHF CB Repeaters are used to retransmit or relay your signal. Repeaters will extend the range of your radio and overcome the shielding effect caused by solid obstructions. Contact a retailer for a list of repeaters available in your area. -
Page 17: Scanning With Priority Channel
2. Press and hold REPLY DELAY While scanning, the GPS105 stops at a busy channel and receives a transmission. When the received signal is over, the unit will wait for 3 seconds for the return of the signal, otherwise the radio... -
Page 18: Instant Channel
UHF CB - OPERATION INSTANT CHANNEL The Instant Channel feature enables a chosen channel to be called at the press of a button. Only one channel at a time is designated as the Instant Channel. To register or change the Instant channel: 1. -
Page 19: Key Beep On/Off
UHF CB - OPERATION KEY BEEP ON/OFF Your radio emits a beep each time one of the keys (except for the PTT button) is pressed. To turn Key Beep ON/OFF: 1. Press & hold MENU 2. Scroll to highlight KEY BEEP . 3. -
Page 20: Gps Operation
GPS OPERATION The GPS antenna must have an unobstructed view of the sky for the GPS105 to retrieve satellite data which is used for the GPS features described on pages 13 to 25. Current regulations permit the SEND POSITION to operate on Channels 22 and 23 only. -
Page 21: Early Warning Safety Alerts
EARLY WARNING SAFETY ALERTS The GPS105 has a preprogrammed memory that will alert you of Fixed Speed Camera, Red Light Camera or Black Spot. These displays automatically pop up and an alert tone sounds when approaching within 400m and 160m of the alert location. -
Page 22: Caller Display
CALLER ID Memories The GPS105 automatically stores CALLER ID data. It will store up to 20 sets of the user name, last received GPS position and the day / month are stored. Once 20 Callers are stored the oldest data is dropped from the list when new callers are added. -
Page 23: Mark Location
GPS coordinates or adjust the coordinates to suit. OPERATION FLOW Example PRESS & HOLD HOME 1. Move the GPS105 to the location you wish to mark, or have the desired coordinates at hand. 2. Press and hold 3. Scroll to highlight desired quick access name. -
Page 24: My Poi Locations
Choose 0001_____ name/ coordinates 1. Move the GPS105 to the location you wish to mark as MY POI, or have the desired coordinates at hand. 2. Press and hold to bring up the mark location list. 3. Scroll to highlight MY POI. -
Page 25: Edit/Delete My Poi
EDIT/DELETE MY POI OPERATION FLOW PRESS & HOLD PRESS MY POI & HOLD Example AAAAAAAAAAAAAA 1. Press and hold to bring up Mark Location List. 2. Scroll to highlight MY POI. 3. Press 4. Scroll to highlight EDIT or DELETE. 5. -
Page 26: Add Or Delete Safety Alert
You can store into memory new safety alert (Fixed Speed Camera, Red Light Camera or Black Spot) locations. If the GPS105 is within 400m of a stored Safety Alert or OPTION location then you can delete this from memory. The OPTION feature is currently unavailable but may in future be pre-programmed with points of interest. -
Page 27: Navigation
When approaching within 160m and 20m of the set destination the NAVI ARRIVE Tone will sound. The compass heading (directional pointer) is referenced to the GPS105's last forward movement. When viewing the compass heading the GPS105 must be facing in the direction of the last forward movement in order to read the compass heading correctly. -
Page 28: Navigate To Quick Access
Navigate to Quick Access OPERATION FLOW Example PRESS OFFICE NAVI 1. Press NAVI 2. Scroll to highlight desired Quick Access Name. 3. Press . NAVI display appears. Press to switch between UHF-CB, NAVI & TRIP COMPUTER displays. DISP To Cancel Navigation press then press NAVI Navigate to CALLER... -
Page 29: Navigate To My Poi
Navigate to MY POI OPERATION FLOW PRESS MY POI NAVI 1. Press NAVI 2. Scroll to highlight MY POI. 3. Press 4. Scroll to find a desired name. To shortcut to the capital letter of the name: Press to highlight the capital letter on the right of the display. Scroll to the desired letter. -
Page 30: Navigate To State/City
Navigate to STATE/CITY OPERATION FLOW PRESS STATE/CITY NAVI Example ACACIA PK 1. Press NAVI 2. Scroll to highlight STATE/CITY. 3. Press The list of Australian States and NZ appears. 4. Scroll to desired state. 5. Press . The City/Suburb list appears. 6. -
Page 31: Trip Computer
TRIP COMPUTER The GPS105 can indicate COMPASS heading and the present speed, average speed, maximum speed and the distance travelled through the TRIP COMPUTER. Press to switch between UHF-CB, NAVI (if navigating) & TRIP COMPUTER displays. DISP The TRIP displays alternate automatically as follows:... -
Page 32: My Position
MY POSITION OPERATION FLOW Press & hold MY POSITION MENU Your current GPS coordinates can be viewed with this selection. 1. Press & hold to bring up the menu list. MENU MENU MY POSITION appears as the first highlighted selection. 2. -
Page 33: Uhf Channels & Frequencies
UHF CHANNELS & FREQUENCIES UHF CHANNELS & FREQUENCIES Simplex Mode Transmit / Receive Frequency (MHz) Frequency (MHz) 476.425 477.175 CH31 476.450 477.200 CH32 477.225 CH33 476.475 477.250 CH34 476.500 476.525 477.275 CH35 476.550 477.300 CH36 477.325 CH37 476.575 477.350 CH38 476.600 476.625 476.650... -
Page 34: Troubleshooting
TROUBLESHOOTING If your GPS105 does not perform to your expectations, try the suggestions listed below. Unit does not operate. No GPS Detection. Cannot send or receive Caller ID. Does not operate in Duplex mode. Check the 2 Amp fuse in the power lead. -
Page 35: Warranty
Uniden, (C) Improperly installed, (D) Repaired by someone other than an authorised Uniden Repair Agent for a defect or malfunction covered by this warranty, (E) Used in conjunction with any equipment or parts or as part of a system not manufactured by Uniden, (F) Installed, programmed or serviced by anyone other than an authorised Uniden Repair Agent, or (G) Where the Serial Number label of the product has been removed or damaged beyond recognition. - Page 36 © 2004 Uniden Australia Pty Limited Uniden New Zealand Limited Printed in China UTZZ01926ZZ...