Page 1
UH7760NB Remote Speaker MIC UHF CB Transceiver For more exciting new products please visit our website: Australia: www.uniden.com.au New Zealand: www.uniden.co.nz...
Contents Introduction Controls & Connectors Indicators Included with your UH7760NB Transceiver Connecting the Microphone Mounting the MIC Hanger Operation Turning on the Power Setting the Auto Squelch Monitor Selecting a Channel Programming the Instant Priority Channel Recalling the Instant Channel...
Introduction The Uniden UH7760NB is designed to provide you with years of trouble free service. Its rugged components and materials are capable of withstanding harsh environments. Please read this Operating Manual carefully to ensure you gain the optimum performance of the unit.
ÀDW EODGH RI D VFUHZGULYHU RU VLPLODU REMHFW FDUHIXOO\ SXVK WKH ORFN WDE RI the MIC plug towards the MIC cord and at the same time tug on the MIC cord to draw back the MIC plug. UNIDEN UH7760NB UHF CB Transceiver...
MIC hanger will determine which parts to use. Conventional Mounting with Screws Use the front part of the MIC Hanger only. Locate a suitable mounting position and mark and drill two 3mm holes. Fix the MIC Hanger into place with screws. UNIDEN UH7760NB UHF CB Transceiver...
Page 10
MIC Hanger mounted over MIC Cable The curly cord of the Remote SPK/MIC can extend up to 1.5m. For practical installation of the MIC Hanger mounted NOTE over MIC Cable use this method with the Extension Cable. UNIDEN UH7760NB UHF CB Transceiver...
Page 11
3. Thread the microphone plug through the hole and connect with the extension cable. 4. Mount the MIC Hanger over the hole and cable. $W WKH 5DGLR &RQQHFW WKH H[WHQVLRQ FDEOH SOXJ WR WKH 0,& -DFN Fit the rubber bushing over the MIC jack. UNIDEN UH7760NB UHF CB Transceiver...
,I WKH LQSXW YROWDJH IDOOV EHORZ 9'& LO DC ÀDVKHV IRU seconds. The power turns off automatically if voltage falls EHORZ 9'& Switch your UH7760NB OFF and disconnect it from the power source, before locating the cause of the power supply problem. UNIDEN UH7760NB...
3 - min sensitivity (max/tight squelch) It requires no adjustment. 1. Press [SQL/MON] 7KH VTXHOFK VHWWLQJ ÀDVKHV 2. Press to change the setting. If tight squelch is selected SQT icon ZLOO DOVR ÀDVK 3. Press [MENU/ENTER] to store the setting. UNIDEN UH7760NB UHF CB Transceiver...
For your reference a list of the available channels, corresponding frequencies and guidelines for their use is printed on p.27 - p.29. For Australia, Channels 05 and 35 NOTE are reserved for Emergency Calls. UNIDEN UH7760NB UHF CB Transceiver...
You may select from 5 types of tones (see p.21). Current regulations require calling tones to be restricted to one transmission per minute. If a second transmission is NOTE attempted within one minute then an error tone will sound. UNIDEN UH7760NB UHF CB Transceiver...
If there is a barrier that partially blocks your transmitted signal, the probability of another radio receiving the signal is very slim. Hills, tall buildings, metallic structures,...etc tend to act as a screen between radios. Standard Operation without the aid of a Repeater station. UNIDEN UH7760NB UHF CB Transceiver...
ON (“ r ” for repeater channels 01 - 08 or “ n “ for repeater channels 41 - 48) or OFF (standard channel numbering). 3. Press [MENU/ENTER] to store the setting. UNIDEN UH7760NB UHF CB Transceiver...
3 seconds for the signal to return, otherwise scanning resumes. After transmission in scan mode, the unit will wait 20 seconds for the signal to return, otherwise scanning resumes. To skip the active channel, press momentarily. To deactivate SCAN, press [SCAN/OS/GS]. UNIDEN UH7760NB UHF CB Transceiver...
If scanning stops on a channel which is not a Priority Channel, UHF CB Radio will continue monitoring the Priority Channel for activity while listening to the active one. To deactivate SCAN, press the [SCAN/OS/GS] button. UNIDEN UH7760NB UHF CB Transceiver...
- OS or GS. Select the channel you want to store. Press to [MEM] store. MEM icon appears and a short tone beep is heard. To remove the channel from SCAN memory, press [MEM] once more. The MEM icon disappears. UNIDEN UH7760NB UHF CB Transceiver...
3. Press [MENU/ENTER] to store the setting. 4. Press and hold [MENU/ENTER] to save & exit from the menu mode. If a button is not pressed within 10 seconds the UHF CB Radio will automatically exit the Menu Mode. NOTE UNIDEN UH7760NB UHF CB Transceiver...
&7&66 LFRQ ÀDVKHV Press on the Remote SPK/MIC to select the desired CTCSS code 01 - 38. Press [DCS/CTCSS] once to store the new setting. To turn off CTCSS (or DCS) select the oFF code during setting. UNIDEN UH7760NB UHF CB Transceiver...
1. Press [MENU/ENTER] six times. 7KH %HHS VHWWLQJ ÀDVKHV 2. Press to change the setting between ON or OFF. 3. Press [MENU/ENTER] to store the setting. 4. Press and hold [MENU/ENTER] to save & exit from the menu mode. UNIDEN UH7760NB UHF CB Transceiver...
/&' &RQWUDVW VHWWLQJ ÀDVKHV 2. Press to change the setting between 01 (low contrast) to 10 (high contrast). 3. Press [MENU/ENTER] to store the setting. 4. Press and hold [MENU/ENTER] to save & exit from the menu mode. UNIDEN UH7760NB UHF CB Transceiver...
The above situations are not a fault of the radio but a symptom of mixed wideband and narrowband radios in current use. It is expected that as older wideband radios are phased out this issue will be eliminated. UNIDEN UH7760NB UHF CB Transceiver...
Terms of Warranty: Uniden Aust/NZ warrants to the original retail purchaser only that the UH7760NB (“the Product”), will be free from defects in materials and craftsmanship for the duration of the warranty period, subject to the limitations and exclusions set out below.
Page 31
Product, together with satisfactory evidence of your original purchase (such as a legible copy of the sales docket) to Uniden at the addresses shown below. You should contact Uniden regarding any compensation that may be payable for your expenses incurred in making a warranty claim.