Table of Contents
Advertisement
Rules for Safe Operation
To help ensure safe operation, please take a moment to learn the machine's applications and limita-
tions, as well as potential hazards. General® International disclaims any real or implied warranty and
hold itself harmless for any injury that may result from the improper use of its equipment.
1. Be sure to read, understand and follow all safety
warnings
and
instructions
Operator's Manual.
2. Do not operate the saw when tired, distracted, or
under the effects of drugs, alcohol or any medica-
tion that impairs reflexes or alertness. Stay alert!
Give your work your undivided attention.
3. Keep the work area well lit, clean and free of
debris. Cluttered areas and benches invite injuries.
4. Keep children and shop visitors at a safe distance
while operating the saw; do not permit them to
operate the scroll saw.
5. Childproof and tamper proof your shop and all
machinery with locks, master electrical switches
and switch keys, to prevent unauthorized or unsu-
pervised use.
6. Fine particulate dust is a carcinogen that can be
hazardous to health. Work in well ventilated area
and use a dust collector whenever possible.
7. Wear approved safety glasses, dust mask and non-
skid footwear. Do not wear loose clothing, gloves,
bracelets, necklaces or jewellery while operating
the saw. Keep long hair contained by wearing pro-
tective hair covering.
8. Be sure all adjustment tools, wrenches or other clut-
ter are removed from the machine and/or the
table surface before operation. When not in use,
tools should be locked-up in a dry place, out of
children's reach and away from flammable sub-
stances.
9. Keep hands well away from saw blade and all
moving parts. Use a brush, not hands, to clear away
chips and sawdust.
10. Be sure that saw blade is properly installed, and in
proper cutting direction, before operation. Always
use a clean, properly sharpened blade. Dirty or dull
blades are unsafe and can lead to accidents. Also,
be sure the blade has gained full operating speed
before beginning to cut.
11. Do not push or force stock into the blade. The saw
will perform better and more safely when working
at the rate for which it was designed. Do not use for
purposes not intended.
12. Avoid working from awkward or off balance posi-
in
the
supplied
13. Never stand or lean on the saw. Serious injury could
14. Use of parts and accessories NOT recommended
15. Never leave the machine unattended while run-
16. Always turn off and disconnect from power source
17. Make sure that switch is in the "OFF" position before
18. Make sure saw is properly grounded. If equipped
19. Repairs to the saw should only be carried out by
20. Inspect power cords and extension wires periodi-
21. This tool is for indoor use only. Do not expose to rain
tions. Do not overreach while cutting; keep both
feet on floor. Never lean over or reach behind the
blade and never pull the workpiece through the cut
from behind.
occur if the unit is tipped over or if the blade is unin-
tentionally contacted.
by General® International may result in equipment
malfunction or risk of injury.
ning or with the power "ON".
before servicing or changing accessories, blades,
bits, and cutters, or before performing any mainte-
nance or adjustments.
plugging in the power cord. Do not use the saw if
the power switch is defected, have defective switch-
es replaced by an authorized service center.
with a 3-prong plug it should be used with a three-
pole receptacle. Never remove the third prong.
Avoid body contact with grounded surfaces (e.g.
pipes, radiators, stoves, refrigerators).
qualified people using original spare parts. A
guard or other damaged part should be properly
repaired or replaced by an authorized service
center.
cally. If damaged, have them repaired by an
authorized service facility. Never yank cords and
wires and keep away from heat, oil, and sharp
edges.
or use in wet or damp locations.
5
Advertisement
Table of Contents
