Related Manuals for Neodrives Z20 RS
Summary of Contents for Neodrives Z20 RS
- Page 1 w w w . n e o d r i v e s . d e D E R H E C K M O T O R Z 2 0 R S | U S E R M A N U A L Alber GmbH Vor dem Weißen Stein 14 72461 Albstadt...
-
Page 2: Table Of Contents
Installation and removal of the rear wheel ............38 02.1.2 LCD and control unit ....................12 05.2 Recuperation ......................41 02.1.3 Battery V8 Z20 RS ......................13 05.3 Thermal management .................... 42 02.1.4 Total system .......................14 02.1.5 Factors influencing the remaining range .............. 15 N O T E S A N D T R O U B L E S H O O T I N G 02.2... -
Page 3: 1 I N T R O D U C T I O N
– no other system should give a smoother, more agile ride than the neodrives hub motor. So just pedal away and enjoy your ride to the max! We hope your ride with the neodrives Z20 RS hub motor is a real pleasure! - Page 4 This user manual describes exclu- CONDITIONS / LOCATIONS FOR USE sively the use of the neodrives components attached to your S-Pedelec and is state-of-the-art at the time of printing. The manufacturer reserves the right to make changes resulting...
-
Page 5: 2 S C O P E O F D E L I V E R Y
H A R N E S S The mounting of the neoNode Z20 RS depends on the bicycle model. It is integrated in the frame. The neodrives Z20 RS drive system has only a few individual components. NOTE : Example, the battery and its positioning may vary depending on the bike. -
Page 6: Technical Data
Hub motor Z20 RS with stub axle Speed 45 km/h neoMMI Z20 RS Power rating peak 1200 Watt neoTwistlock Z20 RS – with neoRemote Z20 RS Operating voltage 48 Volt Torque receiver Nominal torque 12 Nm Z20 RS Cable harness, available in different lengths Peak torque 40 Nm... -
Page 7: Neoremote Z20Rs
( n e o R E M O T E Z 2 0 R S A N D n e o T W I S T L O C K Z 2 0 R S ) The neodrives Z20 RS hub motor is available in combination with the battery V8 Z20 RS, please observe the separate user n e o R E M O T E Z 2 0 R S ( C O N T R O L E L E M E N T ) manual for the battery. - Page 8 0 2 . 1 . 5 | F A C T O R S I N F L U E N C I N G T H E R E M A I N I N G R A N G E N O T E S The neodrives motor was designed for high performance and achieves an efficiency factor of approx. 87 %. As this is a direct -10 °C to +60°...
- Page 9 L C D F I X I N G B R A C K O N T H E n e o T W I S T L O C K Z 2 0 R S W I S T L O C K Z 2 0 R S If required, you can attach the LCD to the neoTwistlock Z20 RS. Use a 1.5 mm Allen key to do this.
-
Page 10: Neonode Z20 Rs
3 seconds If you have to open the two plugs of the cable leading from • Activate recuperation the neoTwistlock Z20 RS mounting plate to the frame, it is es- sential to observe the following instructions when assembling. NOTES: The male plug of the mounting plate (see illustra-... -
Page 11: 3 N E O M M I
0 3 | n e o M M I 0 3 .1 | S O F T K E Y S The neoMMI Z20 RS is equipped with a 2-inch colour TFT LCD with 3 softkeys (keys on touch LCD). This LCD can be operated with the rocker arm unit neoRemote Z20 RS (→... -
Page 12: Display Types
The LCD has 3 display modes: the main display, the power display and the trip display. Use the "Set" button on the neo- Remote Z20 RS rocker arm control → see chapter 2, to toggle To access the menu, please press the "Menu" button briefly. - Page 13 →siehe Seite 22. Battery Units Language Time & date Update A software update temporarily stored on the neoMMI Z20 RS can be installed by tapping "Update". This will be uploaded to the S-Pedelec once the display is ope- ned.
- Page 14 Do not turn the LCD from the neoTwistlock Z20 RS, do Touchscreen Inactive not switch it off via the neoRemote Z20 RS or the battery and do not remove the battery. Always active You can select and tap one of the 5 menus displayed. This Select the desired menu item.
- Page 15 U N I T S M E N U I T E M T I M E & D A T E M E N U I T E M In this menu, you can set whether you prefer metric units (kilo- In this menu, you can set the time and date shown in the metres per hour (km/h) and a 24-hour clock) or imperial units display.
- Page 16 When the walk assist is activated, the symbol appears in the LCD. To activate the walk assist, start moving the bike and hold the "+" button on the neoRemote Z20 RS for three seconds. Keep the "+" button pressed for as long as you wish to be assisted by the motor.
-
Page 17: 4 B A T T E R Y
Pressing the ON/Off button on the neoRemo- After switching off the S-Pedelec and removing the charging te Z20 RS is sufficient (siehe Seite 18). The system powers plug, the battery goes into "Deep sleep" mode to reduce the up after a few seconds (5 seconds), the light switches on and standby power to a minimum. - Page 18 0 4 . 3 | C H A R G I N G A N D S TO R I N G T H E B AT T E R Y The battery can remain in the S-Pedelec while it is being When the battery is fully charged, the battery charger charged.
- Page 19 Insert the battery and press down until you hear and feel it click into place. Integrated battery V8 Z20 RS K E Y N U M B E R Prior to delivery of the S-Pedelec, please note the key num- bers and the manufacturer, e.g.
-
Page 20: 5 M O T O R
0 5 | M O T O R 0 5 .1 | I N S TA L L AT I O N A N D M O U N T I N G T H E D R I V E W H E E L R E M O VA L O F T H E R E A R W H E E L Ensure that all components attached to the wheel have been assembled in accordance with the manufacturer's... -
Page 21: Recuperation
0 5 . 2 | R E C U P E R AT I O N S A F E T Y P R E C AU T I O N S In recuperation mode, the motor acts as a generator. Power is Before inserting the motor plug into the motor, check generated, and this is used to charge the battery. -
Page 22: Thermal Management
This reduces the range, and the heat has to be dissipated. In neodrives motors, this heat dissipation is achieved via a large contact surface of the motor interior (stator carrier) to the dropout or rear end of the bicycle frame. In addition, cooling fins inside and outside the drive housing ensure the greatest possible heat exchange with the environment. -
Page 23: Maximum Axle Load
0 6 | N O T E S A N D T R O U B L E S H O O T I N G 0 6 .1 | M A X I M U M A X L E LOA D The maximum axle load of the motor is 120 kg. -
Page 24: Transport
C L E A N I N G T H E M O T O R • Always transport the battery and the LCD inside your car. • The LCD and battery should also be removed during trans- The motor of your S-Pedelec should be regularly cleaned of port inside the vehicle (e.g. - Page 25 If just one of these factors is not optimal, the range can be significant- • Check the setting of the assistance levels via your neodrives app ly less. Example: At an outdoor temperature of 0°C, the range can be reduced by 30-40%.
- Page 26 w w w . n e o d r i v e s . d e Alber GmbH Vor dem Weißen Stein 14 72461 Albstadt Phone 07432 2006-0 Fax 07432 2006-299 info@alber.de...