Summary of Contents for Newco AKPA-3 DB-T HW
- Page 1 Issued August 2013 INSTALLATION and OPERATION MANUAL For MODEL AKPA-3 DB-T HW TEA BREWER & HOT WATER FAUCET MACHINE...
- Page 2 Issued August 2013...
- Page 3 Issued August 2013 AKPA DB T-3 HW Combin nation ot Water/T ea Brewer...
- Page 4 Issued Aug ust 2013 AKPA DBT-3 3 HW PECIFICAT TIONS Brewer Spec ectrical: 600 240V 30 Amps Sing gle Phase Hot Water Tank: 2.2 G Gallon Cap Independ dent Hot W Water System m with Pow wer Switch Indep endent Tea a Brewer w ith Power Switch...
- Page 5 Issued August 2013...
-
Page 6: Electrical Hook-Up
Issued August 2013 BREWER SETUP PLUMBER'S INSTALLATION INSTRUCTIONS CAUTION: Power to brewer must be OFF before proceeding with plumbing installation. 1) Flush water line before installing brewer. Brewer should be connected to COLD WATER LINE for best operation. 2) Water pressure should be at least 20 lbs. For less than a 25 ft run, use 1/4" copper tubing and connect to 1/2" or larger water line. -
Page 7: Quality Check
Issued August 2013 3) Place a suitable container in place below the brew basket to catch water. Depress one of the brew start/stop switches. If the brewer is up to temperature the brew cycle will begin immediately, if not the brewer will go into autoarm mode. In autoarm mode the heating light will begin to flash but the fill portion of the brew cycle will not begin until the optimum (preset) temperature has been reached. - Page 8 Issued August 2013 TEA BREWER FEATURE DESCRIPTIONS The AKPA brewer incorporates the latest features in brewer control technology. Although providing for enhanced functionality brewer controls remain intuitive and setup of key operating parameters couldn’t be easier. Multiple brew volumes, visa-brew delay, tank temperature set point, brew mode, filter parameters and more are all set from the front control panel using a digital display for precise control.
-
Page 9: Control Panel Layout
Issued August 2013 Filtering Flow Rate – This is the flow rate of incoming water and is used to calculate the volume of water that has been filtered. The flow rates may be turned off or set for .25, .50, .75 or 1.00 gallon per minute (gpm) flow rates. The PDS valve on the rear of the unit should be calibrated to match the recommended flow rate of .25 gpm to properly display the brew volume in the quality check mode and to deliver the programmed brew volume. -
Page 10: Error Messages
Issued August 2013 PROGRAMMING SEQUENCE OF PROGRAMMING STEPS FOR THE DIGI-BREW CONTROLLER ∗ Depress and hold QUALITY button until display lights up (Approx. 10 seconds). ∗ You are now in the Program Mode. Functions to be programmed appear in the order in which they are shown in the following table. -
Page 11: Warranty
No warranty expressed or implied other than the aforesaid is made or authorized by Newco Enterprises, Inc. Prompt disposition will be made if item proves to be defective, within warranty. Before returning any item, write or call Newco, or the dealer from whom the product was purchased, giving model number, serial number, and date of purchase, and... - Page 12 Parts List for AKPA-DBT3 HW (Tea function) Electrical Components Cabinet Parts and Assemblies 119895 Faceplate Ass'y With Boards, AKPA-3 DB-T HW 119911 3 Station Cover Assembly, AKP 119924 Faceplate Ass'y Without Boards, AKPA-3 DB-T HW 110625 Pour-In Grid and Cover Assembly...
- Page 13 Issued August 2013 TEA BREWER FUNCTION WIRING DIAGRAM...
- Page 14 Issued August 2013 INSTRUCTION SHEET FOR AKPA-HW HOT WATER FAUCET FUNCTION Follow the installation instructions using the main manual. Be sure proper waterline is connected to the brewer and the water is turned on. Also, be sure when plugging in the unit that it is connected to the proper size, voltage and amperage receptacle.
- Page 15 Issued August 2013...
- Page 16 Issued August 2013 PARTS LIST-HOT WATER TANK ASSY ITEM # PART # DESCRIPTION 781468 FITTING, FAUCET 800244 GASKET, NYLON-.671 X .937 X .062 119879 NUT,FAUCET,3/8-18, CHROME PLATED 100190 NUT, ½-20, JAM, BRASS 100409 GASKET, BRASS .520ID, TIN PLATE 100269 BRACKET, HIGH LIMIT THERMOSTAT 111593 THERMOSTAT, MANUAL RESET 110978...
- Page 17 Issued Aug ust 2013...
- Page 18 Issued August 2013 PARTS LIST-HOT WATER/ TEA MISC. ITEM PART # DESCRIPTION 119911 COVER ASSY, AKPA,HW 119904 COVER,REAR, AKPA, HW 111719 BOARD, HOT WATER DISPENSE 110958 RELAY, 12V DC, SPST, 30 AMP 120805 VALVE, ASSY, AKPA 119894 ASSY, TUBE, INLET, HW, ¼ COPPER 119889 ASSY, TUBE, DISCHARGE, AKPAHW 119909...
- Page 19 Issued August 2013 HOT WATER FAUCET TROUBLESHOOTING GUIDE PROBLEM PROBABLE CAUSE REMEDY 1. No Water a.) Water turned off a.) Turn on – open shutoff valve b.) Water line not connected b.) Ensure water line is connected c.) Faulty water inlet valve c.) Check valve and connections –...
- Page 20 Issued August 2013...
- Page 21 Issued Aug ust 2013 Identif fying the w ater probes s on the bre ewer’s tank k lid assemb page 14 to o the hot wa ater wiring diagram on n page 19. Liquid Lev vel Probe 2 Left-hand lo ong probe o page 14 item m # 13 [13A...
- Page 22 Issued Aug ust 2013 ANK LID ASSEM BLY AK KPA DBT T-3 HW 3 3500W [ [119853] ITEM PART # ESCRIPTION 100190 am Nut, 1/2-20 0 Brass 100212 6 Lock Washe er, External T Tooth SS 100243 ut, 4-40 Hex S 100409 asket, Brass .520 ID Tin P...
- Page 23 Issued Aug ust 2013...
- Page 24 Issued August 2013...