JVC D-ILA DLA-M2000LU Instructions Manual page 42

I
Quick Reference Guide for PC Menu Mode
Main Menu in PC Menu Mode (While receiving computer-related signals)
Image adj. → (Refer to page 47)
Brightness:
Contrast:
Sharpness:
All reset:
Setting
Tracking:
Phase:
Position:
Resize:
Clamp:
Color temp.
Color temp.:
R-Gain:
G-Gain:
B-Gain:
All-reset:
Options → (Refer to page 52)
Options 1
Menu display: 15sec* (Menu disappears in 15 seconds.) / ON (Menu stays on.)
Line display:
Keystone:
PC2 (BNC):
Options 2:
Language
Japanese / English* / German / Spanish / Italian / French
Information → (Refer to page 54)
Input:
Switcher:
Resolution:
Frequency H: Shows the horizontal frequency of the input signal being received. (
Frequency V: Shows the vertical frequency of the input signal being received. (
Lamp time:
* : Factory set value.
Brightness of the picture image being projected can be adjusted. (–30 to +30, 0*)
Contrast of the picture image being projected can be adjusted. (–30 to +30, 0*)
Adjust the outline of letters etc. (1 / 2 / 3 / 4 / 5, 3*)
Resets above items to the factory set values.
Yes / No
The lateral size and display area of picture image can be adjusted. (–128 to +127)
→ (Refer to page 46)
Flickering or dim picture image can be adjusted. (0 to 31) → (Refer to page 46)
Video screen position and menu position can be adjusted. → (Refer to page 49)
Disp. Posi. / Menu
The relationship between the number of pixels (resolution) and the screen can be selected.
→ (Refer to page 51)
"1:1": Picture image is projected with its original size.
Panel: Picture image is enlarged to the full size.
Aspect*: Picture image is enlarged while maintaining the original aspect ratio.
Selectable clamp position. Normally, set to "BP". ST / FP / BP*
Adjustable color temperature, Low/Middle* /High.
Will be adjusted to correct reddish or blueish image.
Adjusts the red level. (o to 255, the adjustable range varies depending on signals)
Adjusts the green level. (o to 255, the adjustable range varies depending on signals)
Adjusts the blue level. (o to 255, the adjustable range varies depending on signals)
Reset above items to the factory set values.
Yes/No
5sec* (Line display such as "PC1" or "PC2" appears on top right of the screen for 5 seconds
when the VIDEO or PC button is pressed.) / OFF (Line display does not appear.)
Press ENTER to enter the Keystone submenu.
Keystone: Adjust to correct the trapezoidal distortion of the projected image.
(–80 to +128, 0*)
RGB* or YP P . Set to RGB when a computer device with analog RGB, V, H/Cs signals is
B R
connected to the PC2 terminals. Set to YP
Y, R-Y) or DTV-format signals (Y, P
Press ENTER to enter the "Option 2" submenu.
Right Left rev.: OFF* / ON (Select for upside-down hanging on the ceiling.)
Top Bottom inv.: OFF* / ON (Select for upside-down hanging on the ceiling.)
RS-232C [bps]: Selectable baud rate (transmission speed). 9600 / 19200*
Sleep time [min:] Selectable sleep times. If no-signal condition continues for the period
of selected time (Unite: Minutes), the projector enters the stand-by
mode. 15 / 30 / 60 / OFF*
Options 1: Press ENTER to return to the "Option 1" submenu.
Language for on-screen display. → (Refer to page 45)
Shows the terminal name selected by the PC button. (PC1or PC2)
This display currently has no meaning. ("CH.0" is usually displayed to indicate that it is not being used.)
Shows the resolution of the input signal being received. (Horizontal × Vertical)
It may not be displayed correctly with some input signals.
Accumulated used hours of the light-source lamp.
P when a device with component signals (Y, B-
B R
, P ) are connected to the PC2 terminals.
B R
Menu Operations
kHz)
Hz)
41