Contents 1 Sådan arbejder du med computeren....................6 Sikkerhedsinstruktioner.................................6 Før du udfører arbejde på computerens indvendige dele................... 6 Sikkerhedsforanstaltninger............................. 7 Beskyttelse mod elektrostatisk afladning (ESD)......................7 ESD-feltservicesæt................................. 8 Efter du har udført arbejde på computerens indvendige dele................... 9 2 Teknologi og komponenter......................10 USB-funktioner..................................10 USB Type-C...................................11 HDMI 2.0....................................
Page 4
WLAN-kort................................... 34 Removing the WLAN card............................34 Installing the WLAN card.............................. 35 WWAN-kort..................................36 Removing the WWAN card............................36 Installing the WWAN card............................36 Tastaturgitter..................................37 Removing the keyboard lattice............................ 37 Installing the keyboard lattice............................38 Tastatur....................................38 Removing the keyboard..............................38 Installing the keyboard..............................
Page 5
Display back cover................................95 Replacing the display cable............................95 4 Fejlfinding..........................97 Dell SupportAssist Pre-Boot System Performance Check-diagnostik................. 97 Kørsel af SupportAssist Pre-Boot System Performance Check................97 Indbygget selvtest af systemkort (M-BIST – Built-In Self-Test)................. 98 Indbygget selvtest af strømskinne til skærmpanel (L-BIST)..................98 Indbygget selvtest af skærmpanel (LCD-BIST)......................
Skade på grund af servicering, som ikke er godkendt af Dell, er ikke dækket af garantien. Læs og følg sikkerhedsinstruktionerne, der blev leveret sammen med produktet.
På grund af den øgede tæthed i de halvledere, der anvendes i nyere Dell-produkter, er følsomheden over for statisk skade nu højere end i tidligere Dell-produkter. Af denne grund gælder nogle tidligere godkendte metoder til håndtering af dele ikke længere.
Det anbefales, at alle feltserviceteknikere altid bruger det traditionelle tilsluttede ESD-antistatiske armbånd og den beskyttende antistatiske måtte ved eftersyn af Dell-produkter. Derudover er det afgørende, at teknikere holder følsomme dele adskilte fra alle isolatordele under udførsel af eftersyn, og at de bruger antistatiske poser.
Efter du har udført arbejde på computerens indvendige dele Om denne opgave Når du har udført udskiftningsprocedurer, skal du sørge for at tilslutte eksterne enheder, kort, kabler osv., før du tænder computeren. Trin 1. Tilslut telefon- eller netværkskabler til computeren. FORSIGTIG: For at tilslutte et netværkskabel skal du først sætte det i netværksenheden og derefter sætte det i computeren.
Teknologi og komponenter Dette kapitel giver detaljerede oplysninger om teknologi og komponenter, der er tilgængelige i systemet. Emner: • USB-funktioner • USB Type-C • HDMI 2.0 • NVIDIA Quadro T1000 • NVIDIA Quadro T2000 • NVIDIA Quadro RTX3000 • NVIDIA Quadro RTX4000 •...
Hastighed I øjeblikket er der fem hastighedstilstande defineret i de seneste USB 3.0/USB 3.1 Gen 1-specifikationer. Baseret på USB-dataoverførsel er de kategoriseret som Low Speed, Full Speed, High Speed (fra version 2.0 af specifikationen), SuperSpeed (fra version 3.0) og SuperSpeed+ (fra version 3.1). Den nye SuperSpeed+ tilstand har en overførselshastighed på 20 Gbps. USB 3.2-standarden er bagudkompatibel med USB 3.1/3.0 og USB 2.0.
Page 12
USB med strømforsyning USB-strømforsyningsspecifikationen er også tæt forbundet med USB Type-C. I øjeblikket anvender smartphones, tablets og andre mobilenheder ofte en USB-forbindelse, når de skal lades op. En USB 2.0-forbindelse giver op til 2,5 W strøm – nok til at oplade din telefon, men så...
Hovedfunktioner ved Thunderbolt 3 over USB Type-C 1. Thunderbolt, USB, DisplayPort og USB Type-C med strømforsyning gennem et enkelt kabel (funktioner varierer mellem forskellige produkter). 2. USB Type-C-stik og -kabler, der er kompakte og reversible. 3. Understøtter Thunderbolt Networking (*varierer mellem forskellige produkter). 4.
Adskillelse og samling SD-kort Sådan fjernes SD-kortet Forudsætninger 1. Følg proceduren i Før du udfører arbejde på computerens indvendige dele. Om denne opgave Figuren angiver placeringen af SD-kortet og giver en visuel fremstilling af fjernelsesproceduren. Billeder, der skal uploades i næste gennemgangscyklus.
Steps 1. Push the SSD door towards left side to release the SSD door from the base cover. 2. Remove the SSD door from the base cover. Installing SSD door Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task The figure indicates the location of the SSD door and provides a visual representation of the installation procedure.
Steps 1. Place the SSD door into its slot on the base cover. 2. Push the SSD door towards right side to lock the SSD door. Next steps 1. Install the card. 2. Follow the procedure in after working inside your computer.
Steps 1. Slide the SSD release latch to unlock the SSD module. 2. Remove the (M2x3) screw that secures the SSD module into its slot on the computer. 3. Remove the SSD module from the computer. 4. Remove the (M2x3) screw that secures the SSD thermal pad to the SSD carrier. 5.
Steps 1. For M.2 2280 SSD: a. Place the M.2 SSD onto its slot on SSD carrier. 2. For M.2 2230 SSD: a. Place the M.2 SSD into the SSD holder. b. Replace the (M2x2) screw to secure the M.2 SSD to the holder. c.
Page 23
Steps 1. Loosen the eight captive screws that secure the base cover to the computer. 2. Using a plastic scribe, pry open the base cover starting from bottom edge of the cover. NOTE: For models shipped without SmartCard reader, pry open the base cover from the smart card reader slot. Use your fingers to pry open the base cover as the use of plastic scribe or any other sharp objects may damage the base cover.
3. Lift the base cover starting from the bottom edge and remove it from the computer. 4. Disconnect the battery cable from the connector on the system board. Installing the base cover Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task The figure indicates the location of the base cover and provides a visual representation of the installation procedure.
I den type tilfælde skal du kontakte Dells tekniske support for at få assistance. Se www.dell.com/contactdell. • Køb altid originalbatterier fra www.dell.com eller via en autoriseret Dell- partner og forhandler. Removing the battery Prerequisites 1. Follow the procedure in before working inside your computer.
Steps 1. Remove the three (M2x5) screws that secure the battery to the computer. 2. Slightly lift the battery and disconnect the battery cable from the connector on the battery. 3. Remove the battery away from the computer. Installing the battery Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure.
Steps 1. Connect the battery cable to the connector in the battery. 2. Place the battery onto its slot in the computer. 3. Replace the three (M2x5) screws to secure the battery to the computer. Next steps 1. Install the base cover.
Page 29
Steps 1. Remove the (M2x3) screw that secures the SSD thermal plate to the M.2 SSD module. 2. Remove the SSD thermal plate. 3. For M.2 2280 SSD: a. Remove the (M2x3) screw that secures the M.2 SSD to the computer. b.
Installing the primary M.2 SSD module Prerequisites NOTE: For computers shipped with M.2 2280 or 2230 SSD installed in slot 3 and/or slot 5. If you are replacing a component, remove the existing component before performing the installation procedure. About this task The figure indicates the location of the primary M.2 SSD and provides a visual representation of the installation procedure.
2. For M.2 2230 SSD: a. Place the M.2 SSD into the SSD holder. b. Replace the (M2x2) screw to secure the M.2 SSD to the holder. c. Place the M.2 SSD module onto its slot on the computer. d. Replace the (M2x3) screw to secure the M.2 SSD module to the computer. 3.
Installing the secondary memory module Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task The figure indicates the location of the secondary and provides a visual representation of the installation procedure. Steps 1.
Steps 1. Gently slide the SIM card cover towards the left side of the system to unlock the SIM card cover. CAUTION: The SIM card cover is very fragile and can be easily damaged if it is not properly unlocked before opening. 2.
Steps 1. Slide the SIM card into the SIM card slot. 2. Snap the SIM card cover down. 3. Slide the SIM card cover towards the right of the system to lock the cover. Next steps 1. Install the base cover.
Steps 1. Loosen the captive screw that secures the WLAN card bracket to the system board. 2. Remove the WLAN card bracket away from the WLAN card. 3. Disconnect the antenna cables from the WLAN card. 4. Slide at an angle and remove the WLAN card from the connector on the system board. Installing the WLAN card Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure.
2. Install the card. 3. Follow the procedure in after working inside your computer. WWAN-kort Removing the WWAN card Prerequisites 1. Follow the procedure in before working inside your computer. 2. Remove the card. 3. Remove the base cover. About this task The figure indicates the location of the WWAN card and provides a visual representation of the removal procedure.
2. Connect the antenna cables to the connectors on the WWAN card. 3. Place the WWAN card bracket above the WWAN card to secure the antenna cables. 4. Tighten the (M2x3) screw to secure the WWAN card bracket to the system board. Next steps 1.
Installing the keyboard lattice Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task The figure indicates the location of the M.2 SSD and provides a visual representation of the installation procedure. Steps 1.
About this task The figure indicates the location of the keyboard and provides a visual representation of the removal procedure. Steps 1. Lift the latch and disconnect the keyboard cable and the keyboard backlight cable from the connectors on the touchpad module. 2.
Page 40
Steps 1. Align the keyboard to its slot on the palmrest 2. Route the keyboard cable and the keyboard backlight cable through the bottom of the palmrest. 3. Replace the seven (M2x2) screws to secure the keyboard to the palmrest. 4.
Primære hukommelsesmodul Removing the primary memory module Prerequisites 1. Follow the procedure in before working inside your computer. 2. Remove the card. 3. Remove the base cover. 4. Remove the battery. 5. Remove the keyboard lattice. 6. Remove the keyboard. About this task The figure indicates the location of the primary memory module and provides a visual representation of the removal procedure.
2. Lift the memory shield from the memory module to remove it from the computer. 3. Pry the securing clips from both side of the memory module until the memory module pops up. 4. Remove the memory module from the memory-module slot. NOTE: Repeat the above steps if there are other memory installed.
4. Place the memory shield above the memory module. 5. Replace the (M2x3) screw to secure the memory shield to the memory module. Next steps 1. Install the keyboard. 2. Install the keyboard lattice. 3. Install the battery. 4. Install the base cover.
4. Lift the heat-sink assembly to remove it from the computer. Installing the heat sink assembly Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task The figure indicates the location of the keyboard and provides a visual representation of the installation procedure. Steps 1.
Strømadapterport Removing the power-adapter port Prerequisites 1. Follow the procedure in before working inside your computer. 2. Remove the card. 3. Remove the base cover. 4. Remove the battery. 5. Remove the heat-sink assembly. About this task The figure indicates the location of the power-adapter port and provides a visual representation of the removal procedure. Steps 1.
Steps 1. Align and place the power-adapter cable on the computer. 2. Place the power-adapter port into its slot on the plamrest. 3. Replace the power-adapter cable bracket on the power-adapter port. 4. Replace the (M2x3) screw to secure the power-adapter cable bracket to the computer. 5.
Steps 1. Disconnect the power button board cable from the connector on the system board. 2. Peel the power button board cable from the palmrest. 3. Remove the (M2x3) screw that secures the power button board to the computer. 4. Remove the power button board with the power button board cable from the computer. 5.
Steps 1. Connect the power button board cable to the power button board. 2. Align and place the power button board with power button cable into its slot on the computer. 3. Replace the (M2x3) screw to secure the power button board. 4.
Steps 1. Remove the (M2.5x2.5) screw that secures the power button assembly with fingerprint reader cable bracket to the power button board. 2. Remove the power button assembly with fingerprint reader cable bracket from the power button board. 3. Disconnect the power button assembly with fingerprint reader cable from the power button board. 4.
About this task The figure indicates the location of the inner frame and provides a visual representation of the removal procedure. Steps 1. Unroute the WLAN and WWAN antenna cables from the routing guide. 2. Remove the eight (M2x5) and the ten (M2x2.5) screws that secure the inner frame to the computer chassis. 3.
Steps 1. Align and place the inner frame in the computer chassis. 2. Replace the eight (M2x5) and the ten (M2x2.5) screws to secure the inner frame in place. 3. Route the WLAN and WWAN antenna cables through the routing guide. Next steps 1.
About this task The figure indicates the location of the smart-card reader and provides a visual representation of the removal procedure. Steps 1. Disconnect the touchpad buttons cable from the touchpad. 2. Disconnect the smart-card reader cable from the connector on the USH daughter board. 3.
Steps 1. Align and place the smart-card reader into its slot on the computer. 2. Replace the two (M2x2.5) screws to secure the smart-card reader in place. 3. Adhere the smart-card reader cable to the touchpad. 4. Connect the smart-card reader cable to the connector on the USH daughter board. 5.
Steps 1. Disconnect the touchpad buttons cable from the connector on the touchpad. 2. Remove the two (M2x2.5) screws that secure the touchpad buttons to the palmrest. 3. Remove the touchpad buttons from the palmrest. Installing the Touchpad buttons Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure.
Steps 1. Place the touchpad buttons into its slot in the palmrest. 2. Replace the two (M2x2.5) screws to secure the touchpad buttons to the palmrest 3. Connect the touchpad buttons cable to the connector in the touchpad. Next steps 1.
2. Disconnect the LED board cable from the SD card reader on the bottom side of the computer. 3. Remove the (M2x2) screw that secures the SD card reader in place. 4. Slide and remove the SD card reader with its cable out of the computer. Installing SD card reader Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure.
Tænd/sluk-knap Removing the power button Prerequisites 1. Follow the procedure in before working inside your computer. 2. Remove the card. 3. Remove the base cover. 4. Remove the battery. 5. Remove the heat-sink assembly. 6. Remove the power button board. About this task The figure indicates the location of the power button and provides a visual representation of the removal procedure.
Steps 1. Place the power button into its slot on the computer. 2. Replace the two (M2x3) screws to secure the power button in place. Next steps 1. Install the power button board. 2. Install the heat-sink assembly. 3. Install the battery. 4.
Steps 1. Remove the two (M2x3) screws that secure the power button assembly with fingerprint reader in its slot on the computer. 2. Remove the power button assembly with fingerprint reader from the computer. Installing the power button assembly with fingerprint reader Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure.
Steps 1. Place the power button assembly with fingerprint reader into its slot on the computer. 2. Replace the two (M2x3) screws to secure the power button assembly with fingerprint reader in place. Next steps 1. Install the power button board assembly with fingerprint reader.
2. Slightly slide the GPU power cable connector outwards to disconnect the GPU power cable from the GPU card. 3. Repeat the above steps to disconnect the GPU power cable from the system board. 4. Peel the GPU power cable from the computer. Installing the GPU power cable Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure.
Systemkort Removing the system board Prerequisites 1. Follow the procedure in before working inside your computer. 2. Remove the card. 3. Remove the door. 4. Remove the secondary M.2 SSD. 5. Remove the base cover. 6. Remove the battery. 7. Remove the primary M.2 SSD.
Page 63
Steps 1. Carefully pry the GPU power cable connector outside the end of the connector head to unlock the GPU power cable connector from the system board on top side of the system. 2. Slightly slide the GPU power cable connector outwards to disconnect the GPU power cable from the connector on the system board. 3.
NOTE: For UMA models, remove the two (M2x3) screws that secure the single beam connector in place on the bottom of the system. 10. Remove the beam connectors from the computer. 11. Remove the (M2x5) screw that secures the display cable bracket in place. 12.
Page 66
Steps 1. Adhere the coin-cell battery to the palmrest and then place the system board on its slot on the palmrest. 2. Replace the three (M2x5) screws to secure the system board to the palmrest. 3. Connect the display cable, touch screen cable (for models shipped with a touch screen) or IR camera cable (for models shipped with an IR camera), power adapter cable, touchpad cable, USH daughter board FFC (for models shipped with a USH daughter board), and power button board cable to the connectors on the system board.
4. Install the keyboard. 5. Install the keyboard lattice. 6. Install the WLAN card. 7. Install the WWAN card. 8. Install the secondary memory. 9. Install the card. 10. Install the primary M.2 SSD. 11. Install the inner frame. 12. Install the battery. 13.
Sådan monteres GPU-kortet Forudsætninger Hvis du genmonterer en komponent, skal du fjerne den eksisterende komponent, før installationsproceduren foretages. Om denne opgave Figuren angiver placeringen af GPU-kortet og giver en visuel fremstilling af installationsproceduren. Billeder, der skal uploades i næste gennemgangscyklus Trin 1.
14. Remove the primary memory. 15. Remove the heat-sink assembly. 16. Remove the inner frame. 17. Remove the GPU power cable. 18. Remove the card. 19. Remove the system board. About this task The figure indicates the location of the speaker and provides a visual representation of the removal procedure. Images to be uploaded in the next review cycle.
Page 70
Steps 1. Align and place the speaker module into its slot on the top edge of the palmrest. 2. Adhere the three piece adhesive tape to secure the speaker cable in place on the palmrest. Next steps 1. Install the system board.
Midterhætte Removing the middle cap Prerequisites 1. Follow the procedure in before working inside your computer. 2. Remove the card. 3. Remove the door. 4. Remove the secondary M.2 SSD. 5. Remove the base cover. 6. Remove the battery. 7. Remove the primary M.2 SSD.
2. Remove the middle cap from the computer. Installing the middle cap Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task The figure indicates the location of the middle cap and provides a visual representation of the installation procedure. Steps 1.
15. Install the base cover. 16. Install the secondary M.2 SSD. 17. Install the door. 18. Install the card. 19. Follow the procedure in after working inside your computer. Skærmmodul Removing the display assembly Prerequisites 1. Follow the procedure in before working inside your computer.
8. Remove the display assembly from the palmrest. NOTE: The touch display assembly for Precision 7550 is a Hinge-Up Design (HUD) assembly and cannot be further disassembled once it is removed from the bottom chassis. If any components in the touch display assembly are malfunctioning and need to be replaced, replace the entire touch display assembly.
Page 77
Steps NOTE: Before installing the display assembly, ensure that the display hinges are opened to a 140-degree angle against the display assembly, to fit the display assembly to the palmrest. Align the screw holes on the hinges on the display assembly to the screw holes on the palmrest. 2.
12. Install the secondary M.2 SSD. 13. Install the door. 14. Install the card. 15. Follow the procedure in after working inside your computer. Håndfladestøtte Removing the palmrest Prerequisites 1. Follow the procedure in before working inside your computer. 2. Remove the card.
Installing the palmrest Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task The figure indicates the palmrest and before performing the pre-installation parts procedures for any palmrest installation procedure. Next steps 1.
2. Install the middle cap. 3. Install the speaker. 4. Install the system board. 5. Install the card. 6. Install the GPU power cable. 7. Install the inner frame. 8. Install the heat-sink assembly. 9. Install the power button power button assembly with fingerprint reader.
22. Remove the display assembly. About this task The figure indicates the location of the display bezel and provides a visual representation of the removal procedure. Images to be uploaded in the next review cycle. Steps 1. Using a flat head tool or a plastic scribe, pry open the display bezel from the two recess points on the bottom edge of the display bezel.
Page 82
Steps 1. Place the display bezel on the display assembly. 2. Press the edges of the display bezel until it clicks onto the display assembly. Next steps 1. Install the display assembly. 2. Install the middle cap. 3. Install the speaker. 4.
21. Install the card. 22. Follow the procedure in after working inside your computer. Skærmpanel Removing the display panel (non-touch) Prerequisites 1. Follow the procedure in before working inside your computer. 2. Remove the card. 3. Remove the door. 4. Remove the secondary M.2 SSD.
Page 84
Steps 1. Remove the two (M2.5x2.5) screws and the two (M2x2.5) screws that secures the display panel to the display assembly. 2. Lift the display panel and turn the display panel over to access the display cable 3. Peel the conductive tape covering the display cable. 4.
Installing the display panel (non-touch) Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task The figure indicates the display panel and provides a visual representation of the installation procedure. Steps 1.
5. Replace the two (M2.5X2.5) and two (M2x2.5) screws to secure the display panel to the display assembly. Next steps 1. Install the display bezel. 2. Install the display assembly. 3. Install the middle cap. 4. Install the speaker. 5. Install the display assembly.
22. Remove the display bezel. 23. Remove the display panel. About this task The figure indicates the location of the display hinge and provides a visual representation of the removal procedure. Images to be uploaded in the next review cycle. Steps 1.
Page 88
Steps 1. Place the display hinge in its slot on the display assembly. 2. Replace the eight (M2.5x2.5) screws to secure the display hinge to the display assembly. Next steps 1. Install the display panel. 2. Install the display bezel. 3.
Kamera Removing the camera (non-touch) Prerequisites 1. Follow the procedure in before working inside your computer. 2. Remove the card. 3. Remove the door. 4. Remove the secondary M.2 SSD. 5. Remove the base cover. 6. Remove the battery. 7. Remove the primary M.2 SSD.
Steps 1. Peel the adhesive tape that covers the camera module. 2. Disconnect the display cable from the camera module. 3. Gently pry the camera shutter cap from the top edge of the camera shutter and remove it from the display back cover. 4.
13. Install the WLAN card. 14. Install the WWAN card. 15. Install the secondary memory. 16. Install the card. 17. Install the primary M.2 SSD. 18. Install the battery. 19. Install the base cover. 20. Install the secondary M.2 SSD. 21.
Sådan monteres P-sensorkortet Forudsætninger Hvis du genmonterer en komponent, skal du fjerne den eksisterende komponent, før installationsproceduren foretages. Om denne opgave Figuren angiver placeringen af P-sensorkortet og giver en visuel fremstilling af installationsproceduren. Billeder, der skal uploades i næste gennemgangscyklus Trin 1.
Page 93
9. Remove the secondary memory. 10. Remove the WWAN card. 11. Remove the WLAN card. 12. Remove the keyboard lattice. 13. Remove the keyboard. 14. Remove the primary memory. 15. Remove the heat-sink assembly. 16. Remove the inner frame. 17. Remove the GPU power cable.
4. Remove the display cable from the display back cover. Installing the display cable Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task The figure indicates the display cable and provides a visual representation of the installation procedure. Steps 1.
8. Install the GPU power cable. 9. Install the inner frame. 10. Install the heat-sink assembly. 11. Install the primary memory. 12. Install the keyboard. 13. Install the keyboard lattice. 14. Install the WLAN card. 15. Install the WWAN card. 16.
Page 96
For installing the components, place the display back cover on a flat surface. 1. Install the display cable. 2. Install the camera. 3. Install the display hinges. 4. Install the P-sensor board. 5. Install the display panel. 6. Install the display bezel.
Check-diagnostik Om denne opgave SupportAssist-diagnostik (også kendt som systemdiagnostik) udfører et fulstændigt tjek af din hardware. Dell SupportAssist Pre-Boot System Performance Check-diagnostik er integreret i BIOS og opstartes internt i BIOS. Den indlejrede systemdiagnostik leverer en række muligheder til særlige enheder eller enhedsgrupper, der tillader dig at: •...
Indbygget selvtest af systemkort (M-BIST – Built- In Self-Test) Om denne opgave Trin 1. Tryk på både M-tasten og tænd/sluk-knappen, og hold dem nede for at starte M-BIST. 2. Batteristatusindikatoren lyser ravgult, når der er en fejl på systemkortet. 3. Udskift systemkortet for at løse problemet. BEMÆRK: Batteristatus-LED'en lyser ikke, hvis systemkortet fungerer korrekt.
Indbygget selvtest af skærmpanel (LCD-BIST) Om denne opgave Trin 1. Hold tasten D nede, og tryk på tænd/sluk-knappen. 2. Slip både tasten D og tænd/sluk-knappen, når computeren starter POST. 3. Skærmpanelet begynder at vise en enkelt farve eller skifte mellem forskellige farver. BEMÆRK: Farvesekvensen kan variere afhængigt af producenten af skærmpanelet.
Table 7. LED codes(continued) Diagnostic light codes Problem description Recommended Solution Unrecoverable SPI Flash Failure Replace System Board 1, 5 EC unable to program i-Fuse Replace System Board 1, 6 Generic catch-all for ungraceful EC code flow Disconnect all power source (AC, battery, coin cell) and errors drain flea power by pressing &...
Page 101
BEMÆRK: Nogle ISP'er (Internet Service Providers) har en kombineret modem/router-enhed. Trin 1. Sluk for computeren. 2. Sluk for modemmet. 3. Sluk for den trådløse router. 4. Vent i 30 sekunder. 5. Tænd den trådløse router. 6. Tænd for modemmet. 7. Tænd computeren. Fejlfinding...
Om denne opgave Dell giver flere muligheder for online- og telefonbaseret support og service. Tilgængeligheden varierer for de enkelte lande og produkter, og nogle tjenester findes muligvis ikke i dit område. Sådan kontakter du Dell omkring salg, teknisk support eller kundeservice: Trin 1.