Related Manuals for Amprobe TMD-50
Summary of Contents for Amprobe TMD-50
- Page 1 TMD-50 Thermocouple Thermometer K Type Users Manual • Mode d’emploi • Bedienungshandbuch • Manual d’Uso • Manual de uso...
- Page 3 TMD-50 Thermocouple Thermometer K Type Users Manual June 2010, Rev.1 ©2010 Amprobe Test Tools. All rights reserved. Printed in Taiwan...
- Page 4 Please check the “Where to Buy” section on www.amprobe.com for a list of distributors near you. Additionally, in the United States and Canada In-Warranty repair and replacement units can also be sent to a Amprobe® Test Tools Service Center (see address below).
- Page 5 Non-Warranty Repairs and Replacement – US and Canada Non-warranty repairs in the United States and Canada should be sent to a Amprobe® Test Tools Service Center. Call Amprobe® Test Tools or inquire at your point of purchase for current repair and replacement rates.
- Page 6 TMD-50 Thermocouple Thermometer K Type 7) “T1 T2/T1-T2” Button 1) “ ” Power Button 8) “MAX/MIN” Button 2) °C /°F Button 9) “>2S APO/ENTER” 3) “ ” Button Button 4) “ADJ” Button 10) LCD Display 5) “p/REL” Button 11) T1/T2 Input...
- Page 7 Screen Display 1) Temperature display 6) Relative mode 2) Low BATT display 7) Data HOLD mode 3) K type of T/C 8) Degrees °C /°F thermocouple 9) T1/T2 thermocouple 4) Auto power off or T1-T2 differential 5) MAX/MIN reading...
-
Page 8: Table Of Contents
CONTENTS SYMBOLS ................2 UNPACKING AND INSPECTION .......... 2 INTRODUCTION ..............3 Features ................3 OPERATION INSTRUCTIONS ..........3 “ “ Power Button ............3 “°C/°F” Selecting the Temperature Scale ..... 3 “ ” Button: Display Back-Light ........3 “ADJ” Button: Adjust thermocouple offset ....4 “p/REL”... -
Page 9: Symbols
• Repeated sharp flexing can break the thermocouple leads. To prolong lead life, avoid sharp bends in the leads, especially near the connector. UNPACKING AND INSPECTION Your shipping carton should include: TMD-50 meter Manual K type Thermocouple AAA Batteries Plain white box... -
Page 10: Introduction
INTRODUCTION There are 2 sets of sockets for thermocouple plugs at the top of instrument marked with T1 and T2. Features • Highly accurate dual input thermometer with 0.1% basic accuracy. • Dual input T1, T2, T1-T2. • Thermocouple offset adjust. •... -
Page 11: Adj" Button: Adjust Thermocouple Offset
key once more to cancel the Back-Light function. Back-Light on lighter Back-Light off “ADJ” Button: Adjust thermocouple offset 1. Insert the bead wire into a known temperature (T) until the display equal to known temperature (T). exp: ice point at 0°C boiling water at 100°C (Press “ADJ”... -
Page 12: Max/Min" Button
“MAX/MIN” Button Press “MAX/MIN” key to enter the MIN MAX recording mode. (Displays the Maximum reading, Minimum reading, “MAX-MIN”, “AVG” reading stored in record mode). Press “MAX/MIN” key to cycle through the MAX, MIN, MAX-MIN, “AVG” readings. In this mode, press “HOLD”... - Page 13 Accuracy Accuracy is specified for operating temperatures over the range of 18°C to 28°C (64°F to 82°F), for 1 year, not including thermocouple error. ±(0.1%rdg+1°C) on -60°C to 1372°C ±(0.1%rdg+2°C) on -60°C to -200°C ±(0.1%rdg+2°F) on -76°F to 1999°F ±(0.1%rdg+4°F) on -76°F to -328°F Environmental Ambient 0°C to 50°C (32°F to 122°F) <80% R.H.
-
Page 14: Maintenance
� - EMC: Conforms to EN61326-1. This product complies with requirements of the following European Community Directives: 89/ 336/ EEC (Electromagnetic Compatibility) and 73/ 23/ EEC (Low Voltage) as amended by 93/ 68/ EEC (CE Marking). However, electrical noise or intense electromagnetic fields in the vicinity of the equipment may disturb the measurement circuit. - Page 15 1. Power is supplied by 4pcs 1.5V (SIZE AAA) UM-4 R03. 2. The “ ” appears on the LCD display when replacement is needed. To replace battery remove screw from back of meter and lift off the battery cover. 3. Remove the batteries from the battery compartment and replace them with new ones.