Connecting A Vcr And Antenna Or Cable Tv (No Cable Box); Connecting A Camcorder - Toshiba TheaterWide 52HMX94 Owner's Manual

Connecting a VCR and antenna or Cable TV (no Cable box)

You will need:
one coaxial cable
two sets of standard A/V cables
• For better picture performance, if your VCR has S-video, use an
S-video cable (plus the audio cables) instead of the standard video
cable. However, do not connect both types of video cables to
VIDEO 1 (or VIDEO 2) at the same time or the picture
performance will be unacceptable.
• If you have a mono VCR, connect L/MONO on the TV to your
VCR's audio out jack using the white audio cable only.
To view the antenna or Cable signal:
Turn OFF the VCR.
Select the ANT 1 video input source.*
To view the VCR:
Turn ON the VCR. Select the VIDEO 1 video input source
on the TV.*
or...Turn ON the VCR. Select the ANT 1 video input source.*
Tune the TV to channel 3 or 4 (whichever channel is vacant
in your area).
To use the TV Guide On Screen recording features:
1. Connect the G-LINK cable according to the instructions
on page 25.
2. Make sure the VCR is connected to the A/V OUT jacks
on the TV (see illustration).
3. Set the VCR to the appropriate line input (refer to your
VCR owner's manual for details), and then turn OFF the
VCR.
4. See Chapter 5 for details on setting up the TV Guide
On Screen system.
5. See Chapter 7 for details on using the TV Guide
On Screen system.

Connecting a camcorder

You will need:
one set of standard A/V cables
• For better picture performance, if your camcorder has S-video, use an
S-video cable (plus the audio cables) instead of the standard video cable.
Do not connect both an S-video cable and a standard video cable to VIDEO
3 at the same time or the picture performance will be unacceptable.
To view the camcorder video:
Select the VIDEO 3 video input source.*
_____________
*
To select the video input source, press INPUT on the remote control (see page 66).
To program the TV remote control to operate other devices, see Chapter 3.
HMX94(E)012-25(2B-Cnct) 13
Chapter 2: Connecting your TV
Stereo VCR
IN from ANT
OUT to TV
TV
OUT 1
S-VIDEO
OUT 2
TheaterNet
VIDEO
L/
MONO
AUDIO
R
VIDEO 1
Note: The VIDEO/AUDIO OUT jacks output the signals from the
ANT 1, ANT 2, VIDEO 1, VIDEO 2, or VIDEO 3 jacks when the
appropriate input mode is selected.
The unauthorized recording, use, distribution, or revision of television
programs, videotapes, DVDs, and other materials is prohibited under the
Copyright Laws of the United States and other countries, and may subject
you to civil and criminal liability.
Copyright © 2004 TOSHIBA CORPORATION. All rights reserved.
VIDEO AUDIO
L R
CH 3
CH 4
L R
From Cable TV
or antenna
ANT1
(CABLE)
IN
AUDIO
R L
2
ANT2
S-VIDEO
Y Y 1
ANT (75 )
P P
B B
VIDEO
VIDEO VAR
P P
R R
AUDIO
L/
L/
MONO MONO
L L L
AUDIO AUDIO
AUDIO
AUDIO
R R
R
R
R
COLOR COLOR
VIDEO 2
STREAM STREAM
HD-1 HD-2
IN OUT
Camcorder
VIDEO AUDIO
OUT
L
R
VIDEO 3 inputs on TV right side panel
9/28/04, 1:39 PM
IN
OUT
TheaterNet CableCARD™
IEEE1394
EJECT
1
2
HDMI IN
2
1
G-LINK
DIGITAL
AUDIO OUT
13