Advertisement
WMK 160 • Installation Guide (Continued)
Step 4.
Cable the Switcher
—
a.
Connect the cables from the PVT wallplates, control device (MediaLink Controller), speakers, and optional accessories
(VoiceLift
and Page Sensor Kit) to the rear ports of the switcher (see figure 7 below).
®
Refer to the PVS 407D Setup Guide for additional details.
NOTE:
If using a device other than a PVS 407D (such as a PVS 405D or PVS 305SA IP), refer to the user guide for
that device.
b.
Run an HDMI cable from the switcher to the output display device through the wall or, where fitted, the raceway.
NOTE:
It is recommended that the HDMI output cable used, should not exceed a distance of 50 feet.
c.
Connect the power supply to the switcher and plug it in to the electrical outlet.
NOTE:
If the electrical outlet is outside the WMK, pass the IEC power cable out through one of the raceway
knockouts.
1/2
3/4
SIG
LINK
SIG
LINK
POWER
12V
3A MAX
PVT IN
PVT IN
M
A
Power Connector
AUDIO IN
AUDIO IN
HDMI IN
VGA IN
e
PVT HD RGB
HDMI or RGB video/audio,
Inputs 1/2 and 3/4,
Supplied PVS
1 XTP DTP 24 cable with RJ-45 connectors
Switcher External
Power Supply
(12 VDC, 4 A, or
12 VDC, 4.2 A)
Figure 7.
Cabling the switcher (PVS 407D shown)
NOTES:
•
Use only the supplied 12 V, 4 A or 12 V, 4.2 A power supply for the PVS 407D or PVS 405D switcher.
•
Either of those power supplies can support a typical system: for example, a PVS 407D, two PVT Wallplates, two
or four speakers, an MLC Plus 100, and a VoiceLift Microphone system.
4
PVS 407D
OUTPUT
INPUTS
5
6
HDMI
HDMI
B
G
HDMI
HDMI
Connector
Connector
HDMI Input
HDMI Output to
Sources,
Display Device
Inputs 5 and 6
NOTES:
• If you use cable that has a drain wire, tie the drain wire
to ground at both ends.
• You must connect a ground wire between the MLC
and PVS.
Line Out
Audio Output
Output
to Speakers
(Audio)
Speaker
PVS terminal
wire color
(left and right)
Red
Positive (+)
Black
Negative (-)
I
AMPLIFIED AUDIO OUT
AUDIO OUT
L
R
DO NOT
GROUND
OR SHORT
4/8
SPEAKER
Ω
OUTPUTS
CLASS 2 WIRING
REMOTE
OVER PVT
RS-232
IR
Tx Rx
G
S G
E
J
K
VoiceLift
Receiver
S G
IR control
Aux Audio
Input 5
Ground (Gnd)
Transmit (Tx)
Receive (Rx)
Connect to the
Ground
+12 VDC input
same power supply
used by the PVS Switcher.
MLC Plus 100 rear panel
To PVS terminal
MLC
wire color
White
Rx on RS-232 port
Violet
Tx on RS-232 port
Drain wire
Ground (G)
Black
PVS Power Supply (–)
Red
PVS Power Supply (+)
Paging
Sensor
4-port 10/100 Ethernet Switch
Input
Connect as follows:
+V
1. TCP/IP network
2. MLC controller
3. Optional network device
4. Optional network device
L
H
F
LAN
LAN
PAGING
SENSOR
1
3
L
R
+V
INPUT 7
AUX
L
R
2
4
C
D
Aux
Input
Receive (Rx)
Transmit (Tx)
MLC Plus 100
RS-232 input
Tx Rx G
Tx Rx G
S
G
V
C
G
IN
G
POWER
COM 1
COM 2
IR
VOL
D IN
12V
x.xA MAX
1
2
C
RELAYS
Advertisement
