Yamaha Clavinova CVP-96 Service Manual page 72

CVP-96/CVP-98
• PAN POT changes the value for the melody voice arid rhythm voice in
relation to the preset value.
• Portamento time is fixed to O when the PORTAMENTO CONTROL is
used.
• HARMONIC CONTENT applies adjustment to the resonance value that
is set by the voice. This parameter specifies relative change with the
value of 64 producing 0 adjustment. As values get higher the sound
becomes increasingly eccentric. Note tliat for some voices the effective
parameter range is narrower than the legal parameter ran_ge.
• RELEASE TIME applies adjustment to the envelope release time set by
the voice. This parameter specifies relative change with the value of 64
producing O adjustment.
• ATTACK TIME appttes adjustment to the envelope attack time set by the
voice. This parameter specifies relative change with the value of 64
producing O adjustment.
• BRIGHTNESS applies adjustment to the cut-off frequency set by the
voice. This parameternpecifies relative change with the value of 64
producing O adjustment. Lower voices produce a softer sound. For
some voices the effective parameter range is narrower than the legal
parameter range.
(3-2) CHANNEL MODE MESSAGES
STATUS 101 lnnnn(BnH)
CONTROL NUMBER 0ccccccc
CONTROL VALUE 0vvvvvvv
(3-2-1) ALL SOUND OFF (Recive only)
n = 0 - 15 VOICE CHANNEL NUMBER
c = CONTROL NUMBER
v = DATA VALUE
(CONTROL NUMBER = 78H , DATA VALUE = 0)
Switches off all sound from the channel. Does not reset Note On and Hold On
conditions established by Channel Messages.
(3-2-2) RESET ALL CONTROLLERS (Recive only)
(CONTROL NUMBER = 79H , DATA VALUE = 0)
Resets controllers as follows.
PITCH BEND CHANGE
AFfERTOUCH
MODULATION
EXPRESSION
SUSTAIN
SOSTENUTO
SOFf PEDAL
NRPN
RPN
PORTAMENT CONTROL
PORTAMENTO
O(Center)
0(min.)
0(min.)
127 (max.)
0 (off)
0 (off) ·
0 (off)
Sets number to null. (Internal data remains unchanged)
Sets nuinber to null. (Internal data remains unchanged)
Rese~ portamento source note number
0(off)
(3-2-3) ALL NOTES
OFF
(Recive only)
(CONTROL NUMBER = 7BH , DATA VALUE = 0)
Switches off all of the channel's "on" notes. However, any notes being held by SUSTAIN
or SOSTENUTO continue to sound_ uritil.SUSTAIN/SOSTENUTO goes off.
(3-2-4) OMNI OFF (Recive only) (CONTROL NUMBER= ?CH, DATA VALUE= 0)
Same processing as for All Notes Off.
(3-2-5) OMNI ON (Recive only) (CONTROL NUMBER = ?DH , DATA VALUE= 0)
Same processing as for All Notes Off. Omni On is not executed.
(3-2-6) MONO (Recive only) (CONTROL NUMBER = 7EH , DATA VALUE = 0)
Same processing as for All Notes Off,
If
the 3rd byte is in a range of 0-16 the
corresponding channel wiHbe changed to Mode 4 (rn=l).
(3~2-7) POLY (Recive only) (CONTROL NUMBER= 7FH , DATA VALUE= 0)
Same processing as for All Sounds Off and the corresponding channel will be
chang~ to Mode 3.
(3-3) REGISTERED PARAMETER NUMBER(RPN}
89
STATUS
IO!
lnnnn(BnH) n =
0 -
15 VOICE CHANNEL NUMBER
RPN LSB 01100100(64Hj
RPN LSB NUMBER Oppppppp
p
=
RPN
LSB(refer to the list below)
RPN MSB 0110010!(65H)
RPN MSB NUMBER Oqqqqqqq q = RPN MSB(refer to the list below)
DATA ENTRY MSB 000001 I0(06H)
DATA VALUE
DATA ENTRY LSB
DATA VALUE
Ommmmmmm
OOIO0I I0(26H)
Olllllll
m = Data Value
l = Data Value
First appoints the parameter for RPN MSB/I.,SB, then _sets the parameter value for
data entry MSB/I.,SB.
RPN D.ENTRY
LSB MSB MSB LSB PARAMETER NAME
DATA RANGE
OOH OOH mmH - PITCH BEND SENSITIVITY OOH - 18H (0 - 24 semitones)
0IH OOH mmH llH FINE TUNE lmmH,IIHJ = !OOH.OOH) - i40H,OOHJ · 17FH.JFHJ
(-8192*100/8192). 0 -(+8192*100/8192)
02H OOH mmH - COARSE TUNE
28H -40H - 58H (-24 -0- +24 semitones)
7FH 7FH NULL
Clears the current RPN number setting. Does rn;,t change the internal parameter settings.
(3•4) NON-REGISTERED PARAMETER NUMBER(NRPN) (Reclve only)
STATUS 101 !nnnn(BnH) n = 0 - 15 VOICE CHANNEL NUMBER
NRPN LSB 01 !000l0(62H)
NRPN LSB NUMBER Oppppppp p = NRPN LSB(refer to the list below)
NRPN MSB 011000_11(63H)
NRPN MSB NUMBER Oqqqqqqq q = NRPN MSB(refer to the
list
below)
DATA ENTRY MSB 00000ll0(06H)
DATA VALUE Ommmmmmm
m ·
=
Data Value
First appoints the parameter for NRPN MSB/LSB. then sets the parameter value for data entry
MSB/LSB.
NRPN D.ENTRY
MSBLSB MSBLSB PARAMETER NAME
DATA RANGE
0IH 08H mmH-
VIBRATO RATE
OOH - 40H -7FH (-64- 0- +63)
0IH 09H mmH- VIBRATO DEPTH
OOH-40H - 7FH (-64-0 · +63)
0IH 0AH mmH-
VIBRATO DELAY OOH -40H - 7FH (-64 • 0 - +63)
0IH 20H
mmH- FILTER CUTOFF FREQUENCY OOH - 40H - 7FH (-64 - 0 - +63)
0IH 21H mmH- FILTER RESONANCE
OOH - 40H- 7FH (-64 - 0 · +63)
0IH 63H mmH- EG ATTACK TIME
OOH - 40H - 7FH (-64 - 0 · +63)
0IH 64H mmH-
EG DECAY TIME 00H-40H - 7FH (-64 - 0- +63)
DlH.66H mmH- EGRELEASE
OOH -40H - 7FH (-64 - 0 - +63)
14H rrH mmH-
DRUM FILTER CUTOFF FREQ. OOH - 40H - 7FH (-64 - 0 - +63)
15H rrH mmH-
DRUM FILTER RESONANCE OOH - 40H - 7FH (-64 - 0 · +63)
16H rrH mmH-
DRUM AEG ATTACK RATE OOH - 40H · 7FH (-64 - 0 - +63)
17H rrH mmH- DRUM AEG DECAY RATE
OOH-40H - 7FH (-64 - 0- +63)
18H rrH mmH- DRUM PITCH COARSE
OOH. - 40H - 7FH (-64 - 0 - +63)
19H rrH mmH- DRUM PITCH FINE
OOH - 40H - 7FH (-64 - 0 · +63)
lAHrrH mmH-
DRUM LEVEL OOH - 7FH (0 - max.)
!CHrrH mmH- DRUM _PANPOT
OOH ,0IH -40H -7FH
(ranp.om,left - center - rig_ht)
!DH rrH mmH - DRUM REVERB SEND LEVEL OOH - 7FH (0 - max.)
!EH rrH mmH - DRUM CHORUS SEND LEVEL OOH - 7PH (0 - max.)
lFH rrH mmH - DRUM VARIATION SEND LEVEL OOH - 7PH (0 - max.)
The MSG 14H-1FH (for drums) message is accepted as long as the channel is set with a drum
voice.
rrH : drum
instrument note number
(3-5) SYSTEM REALTIME MESSAGES
(3-5-1) MIDI CLOCK
STATUS 11111000 (FSH)
Transmission:
96 clocks per measure
are
transmitted.
Reception: If
the instrument's clock is set to external, after FAH is received from the
external device the instrument's clock will sync with the
96
beats per measure
received from the external device.
Decides whethe~ the internal clock, or Timirig Clocks received via the MIDI IN will
be used.
(3-5-2) START
STATUS 11111010 (FAH)
Transmission: Transmitted when instrument's Rhythm or Song playback is started.
Reception:
Depending upon the condition, Rhythm, Song Playback, or Song Rec will
start.
(3-5-3) STOP
STATUS 11111100 (FCH)
Transmission:
Transmitted when instrument's Rhythm or Song playback is stopped.
Reception: Depending· upon the condition, Rhythm, Song Playback, or Song Rec will
stop.
(3-5-4) ACTIVE SENSING
STATUS 11 ll 1110 (FEH)
Transmission:
Transmitted approximately once every 200msec.
Reception:
Sensing is started once this Code is received.
If
Status or Data is not
received within 400ms, the MIDI Receive Buffer will be cleared, ·and all notes;
including those being sustained, will be cut OFF. Also, al) control values will be reset
to their factory defaults.