Semi-Flush Fixing Kit; Technical Data - Honeywell GENT S-Quad Data And Installation

Data and Installation
S-Quad Semi-flush
fixing kit (S4-FLUSH)
An S-Quad device can be semi-flush mounted to a ceiling tile to
an approximate depth of 20mm, which is slightly deeper than the
base assembly. To semi-flush mount a special housing must be
used, which consists of a main assembly and a trim ring.
"
There is an enhanced volume output of sound
and speech from a flush mounted S-Quad.
Clamp
Cut a 140mm
diameter hole in the
ceiling tile.
( If required use a Bi-Metal Holesaw
140mm or 146mm, from
www.shop4tools.co.uk
Insert the flush shroud
assembly into the hole
in the ceiling tile.
Hold the flush shroud
to the ceiling tile and tighten
the three screws to splay the
clamps to secure the shroud to the tile.
Fit the metal box onto the back
of the flush shroud using the
appropriate fixing screws to secure
the box to the flush shroud.
Locate the S-Quad Base into
the flush shroud, such that the
two locating pillars on the
shroud feeds through the two
elongated holes on the Base.
Push the Base into the shroud
until the Base click locks into
the shroud.
Make the cable connections.
Offer the trim ring to the shroud
and slowly rotate ring clockwise until it
clicks and goes no further. This will
lock the ring in position.
Offer the S-Quad to the Base
and rotate the S-Quad clockwise
until it moves upwards into Base,
and then rotate the S-Quad again
until it clicks and goes no further.
WEEE Directive:
At the end of their useful life, the packaging,
product and batteries should be
disposed of via a suitable recycling centre.
Do not dispose of with your normal household waste.
Do not burn.
At the end of their useful life, the packaging,
product and batteries should be disposed of
via a suitable recycling centre and in
accordance with national or local legislation.
Gent by Honeywell reserves the right to revise this publication from time to time and make changes to the content hereof without
obligation to notify any person of such revisions of changes.
4
)
Do not over tighten the clamping
screws as this will cause the
clamps to cut into the ceiling tile.
Hamilton Industrial Park, Waterside Road, Leicester LE5 1TN, UK
Telephone +44 (0) 116 246 2000

Technical data

Weight
Dimensions
Enclosure
Colour
Storage Temperature -20°C to +70°C
Ambient temperature -10°C to +50°C
Relative Humidity
Metal back box
Cross section
of Ceiling Tile
Flush shroud
S-Quad Base
Trim ring
S-Quad
Further
information about
these products
S4-715 (EN54-7, 17 & 18)
can be found in
S4-710 (EN54-5, 7, 17 & 18)
S4-720 (EN54-5, 17 & 18)
Part 2 of this S4-770 (EN54-3, 5, 7,17 & 18)
S4-711 (EN54-5, 7, 17 & 18)
document
available on Gent
Expert website.
Technical support: www.gentexpert.co.uk
164g with trim ring
174mm diameter by 50mm depth
ABS
RAL 9010
95% non condensing
(+5 to +45°C)
0832
Gent by Honeywell (Novar Systems Limited)
Manufactured by: Honeywell Life Safety Systems,
140 Waterside Road, Hamilton Industrial Park,
Leicester, LE5 1TN, United Kingdom
13
DoP Product No. DoP
017-CPR-2013
001-CPR-2013 S4-715
001-CPR-2013 S4-710 017-CPR-2013
001-CPR-2013 S4-720 017-CPR-2013
001-CPR-2013 S4-770 017-CPR-2013
001-CPR-2013 S4-711 017-CPR-2013
017-CPR-2013
017-CPR-2013
017-CPR-2013
EN54-3:2001, A1: 2002, A2:2006, EN54-5:2002,A1:2002,
EN54-7:2000, A1:2002, A2:2006, EN54-17:2005, EN54-18:2005
S4-911-ST-VO (EN54-3, 5, 7,17 & 18)
S4-911
S4-711-ST
S4-711-ST-VO (EN54-3, 5, 7, 17 & 18)
S4-711-VO
S4-720-ST-VO (EN54-3, 5, 17 & 18)
S4-771
S4-780
Intended for use in fire detection and fire alarm systems
in and around buildings
Refer to DOP 001-CPR-2013 and 017-CPR-2013 for level or
class of performance declared, for details see website ww w.gent.co.uk
Website: www.gent.co.uk
Fax (UK): +44 (0)116 246 2300
4188-779 issue 10_12/13_S-Quad _Part 1
S-Quad
Product No.
S4-911-ST-VO
S4-911
S4-711-ST
S4-711-ST-VO
S4-711-VO
S4-771
S4-720-ST-VO
S4-780
(EN54-5, 7, 17 & 18)
(EN54-5, 7, 17 & 18)
(EN54-3, 5, 7, 17 & 18)
(EN54-3, 5, 7,17 & 18)
(EN54-3, 5,17 & 18)