Advertisement
Quick Links
Advertisement
Related Manuals for Edelbrock 1584
Summary of Contents for Edelbrock 1584
- Page 1 Edelbrock E-Force Supercharger 2011-2014 Ford F-150 5.0L Part Number 1584, 15840...
-
Page 2: Tools And Supplies Required
160° of twist for maximum flow, minimum temperature rise, quiet operation and the reliability for which Eaton is known. The rotors however, are merely the foundation of the system. The Edelbrock Supercharger is a complete system that maximizes efficiency and performance by minimizing air restriction into, and out of, the supercharger. In addition, Edelbrock inverted the supercharger and packaged it down low in the valley allowing for an incredible 15 inches of runner length to maximize part throttle low end torque. -
Page 3: Important Warnings
Due to the complexity of the Edelbrock E-Force Supercharging system, it is recommended that this system only be installed by a qualified professional with access to a service lift, pneumatic tools, and a strong familiarity with automotive service procedures. - Page 4 Check the website to ensure you have the latest version, as described in Step #108. It is also recommended that you check the Edelbrock Tech Center Website for any updates to this installation manual. Please refer to the lower right hand footer to verify that you have the latest revision of this installation manual before beginning the installation.
- Page 5 (1x) - M8 x 1.25 x 30mm Hose Clamp Hex Flange Bolt Hex Flange Bolt (2x) - Spacer, Recovery (1x) - M6 x 1.0 x 10mm Tank Hex Flange Bolt Brochure #63-1584 ©2017 Edelbrock LLC Rev. 12/11/17 - NP Page 5 Part #1584, 15840...
- Page 6 Manifold Intake Elbow Driver Side PCV Fuel Rail Crossover Water Pump to Manifold to Recovery Tank Recovery Tank To Water Pump LTR to Manifold Heater Hose Brochure #63-1584 ©2017 Edelbrock LLC Rev. 12/11/17 - NP Page 6 Part #1584, 15840...
- Page 7 (MAF Connector) ACT Harness MAF Sensor ACT Sensor Water Pump Harness Ground Strap Relay Water Pump EVAP Solenoid Fuse Engine Harness (EVAP Connector) Power Supply Wire Brochure #63-1584 ©2017 Edelbrock LLC Rev. 12/11/17 - NP Page 7 Part #1584, 15840...
- Page 8 ECU thus verifying that they are compatible. Original Equipment Manufacturers often release updates to the computer programming for your vehicle. Edelbrock highly recommends that you verify, with your new car dealer, that your vehicle is equipped with the latest software version from your vehicle manufacturer, before attempting to load the Edelbrock tune.
-
Page 9: Supercharger Installation
EVAP connector. Use an 8mm socket to remove the two (2) bolts retaining the EVAP solenoid. Set the solenoid and bolts aside as they will be reused later. Brochure #63-1584 ©2017 Edelbrock LLC Rev. 12/11/17 - NP Page 9 Part #1584, 15840... - Page 10 16. Use an 8mm socket to remove six (6) manifold bolts (there are a total of ten (10) manifold bolts, four (4) of which were removed in Step 11). Brochure #63-1584 ©2017 Edelbrock LLC Rev. 12/11/17 - NP Page 10 Part #1584, 15840...
- Page 11 If you have any questions passenger side coolant fitting. Pull the fitting out of the please contact Edelbrock’s Tech Hotline at 800-416-8628. cylinder head and set it aside for reuse later. Cover the 24. Position the A/C compressor belt behind the crankshaft cavity with masking tape to prevent debris from entering.
- Page 12 1 full rotation to verify the A/C compressor belt has correctly seated onto the crankshaft and A/C compressor pulley. Inspect the belt for any damages before proceeding. Brochure #63-1584 ©2017 Edelbrock LLC Rev. 12/11/17 - NP Page 12 Part #1584, 15840...
- Page 13 Torque to 18 ft-lbs. NOTE: 2014 Model Years will use a smaller 65mnm idler pulley. 90mm 36. Using a 15mm socket, remove the left bolt securing the alternator. Brochure #63-1584 ©2017 Edelbrock LLC Rev. 12/11/17 - NP Page 13 Part #1584, 15840...
- Page 14 NOTE: Because of the placement of the motor and the from the thermostat housing. Use an deep 10mm socket height of the Edelbrock supercharger, the supercharger with a drive extension, gently bend this fitting roughly 5° must be disassembled and installed in three parts. Please outboard so that it will clear the supercharger manifold.
- Page 15 Brochure #63-1584 ©2017 Edelbrock LLC Rev. 12/11/17 - NP Page 15 Part #1584, 15840...
- Page 16 58. Tighten the inner manifold/runner bolts to 8 ft/lbs. Then tighten the outer manifold/runner bolts to 8 ft-lbs. DO NOT Passenger Side overtighten bolts as they may strip the threads. Brochure #63-1584 ©2017 Edelbrock LLC Rev. 12/11/17 - NP Page 16 Part #1584, 15840...
- Page 17 68. Install the supplied fuel cross over hose onto the two (2) center fittings on the driver and passenger fuel rails. Brochure #63-1584 ©2017 Edelbrock LLC Rev. 12/11/17 - NP Page 17 Part #1584, 15840...
- Page 18 72. Install the supplied heater hose to the firewall fitting and connect the heater hose to the driver side coolant fitting next to the throttle body flange. Brochure #63-1584 ©2017 Edelbrock LLC Rev. 12/11/17 - NP Page 18 Part #1584, 15840...
- Page 19 78. Install the manifold to recovery tank hose using two (2) Pass Side LTR Bracket LTR Bracket 3/4” hose clamps from bag #3. Water Pump Bracket Bumper Reinforcement Bolts M6 x 10mm Crash Beam Nut Brochure #63-1584 ©2017 Edelbrock LLC Rev. 12/11/17 - NP Page 19 Part #1584, 15840...
- Page 20 LTR to manifold hose onto the outlet port of the LTR. Route mounting location. the hose under the driver side radiator shroud towards the manifold. Brochure #63-1584 ©2017 Edelbrock LLC Rev. 12/11/17 - NP Page 20 Part #1584, 15840...
- Page 21 90. Install the factory EVAP hose onto the EVAP solenoid. 94. Reinstall the actuator hose back onto the actuator and secure the actuator hose to the factory retaining clip located on the EVAP hose. Brochure #63-1584 ©2017 Edelbrock LLC Rev. 12/11/17 - NP Page 21 Part #1584, 15840...
- Page 22 Route POSITIVE (+) lead on the water pump harness over towards the positive terminal of the battery and install using a 8mm socket (10mm on some vehicles). Brochure #63-1584 ©2017 Edelbrock LLC Rev. 12/11/17 - NP Page 22 Part #1584, 15840...
- Page 23 If you have yet to flash your ECU, then proceed with steps 108 - 120, otherwise disregard them. 108. It is recommended that you check the Edelbrock website at: (http://www.edelbrock.com/automotive_new/ mc/superchargers/fuel_injected_soft-tech.shtml) to confirm that you have the latest calibration.
- Page 24 ‘Key On, Engine Run’ test. 123. Check all fluid levels before operating vehicle. Congratulations on the installation of your new Edelbrock E-Force Supercharger System. If you have any questions, please call our Technical Support hotline and one of our technicians will be happy to assist you.
- Page 25 • Open the SCT software and select the button on the lower left hand side that reads GET STOCK FILE FROM DEVICE. Follow the instructions on the screen. • Once the download is complete e-mail your stock calibration to Calibration@edelbrock.com, or call 1-800-416-8628 and our tech support staff will assist you in e-mailing the file.